HURRAN SB1208BZUS-HR-8LT-BLACK Matte Black Bathroom Sink Faucet Installation Guide
- June 17, 2024
- HURRAN
Table of Contents
FAUCET INSTRUCTION
SB1208BZUS-HR-8LT-BLACK Matte Black Bathroom Sink Faucet
*Scan the QR code or search HURRAN on YouTube to watch the installation video.
https://www.youtube.com/channel/UCcYA2P844ugiaSMDYocc3JA
If you need installation assistance, replacement parts or have questions regarding our limited lifetime warranty, please email our 24h customer service team: hurranserviceteam@gmail.com
To ensure that your installation proceeds smoothly, please read all instructions carefully.
Please inspect the product if there is any damage during transport.
Thank you for choosing HURRAN.
Parts List
① Faucet Body
② Handle Assembly (x2)
③ Rubber Washer (x3)
④ Metal Washer (x3)
⑤ Drain Assembly| ⑥ Mounting Nut (x3)
⑦ Screw (x6)
⑧ Quick Connect Hose
⑨ Hose (x2)
---|---
HELPFUL TOOLS
Cleaning and Care
- Simply wipe gently with a damp cloth and blot dry with a soft towel.
- Do not use abrasive cleaners, steel wool, or harsh chemicals when cleaning this faucet.
Safety notes
Wear safety goggles and gloves during installation in case any crushing or
cutting injuries.
The pressure of hot and cold supplies should be the same.
Installation Instructions
- Prior to installation: Shut off water supply. Remove old faucet. Clean the mounting surface.
- Cover the sink drain to avoid losing any parts.
- The drain valve must only be used as intended. It is not allowed to attach other objects to the drain valve, for example a semi-pedestal.
- Observe all local plumbing and building codes.
Technical Data
| Operating pressure: | max. 1 MPa |
|---|---|
| Recommended operating pressure: | 0,1 – 0,5 MPa |
| Test pressure: | 1,6 MPa |
(1 MPa = 10 bar = 147 PSI)
Recommended hot water temperature:| max. 65°C
Thermal disinfection:| max. 70°C / 4 min
- SHUT OFF WATER SUPPLIES. Remove the old faucet.Remove the mounting nut and washer from the handles.
- Remove the mounting nut and washer from the faucet.
- Place the hot and cold water handles through the mounting holes.
- Secure the handles to the sink using the washer and mounting nut. Leave at least 0.2 inch gap between the mounting nut and sink.
- Securely tighten the screws on the mounting nut with the screwdriver. Before final tightening, be sure that both handles rotate correctly.
- Place the faucet through the center mounting hole.
- Secure the faucet to the sink using the washer and mounting nut. Leave at least 0.2 inch gap between the mounting nut and sink.
- Securely tighten the screws on the mounting nut with the screwdriver.
- Push the middle quick connect hose connection onto the faucet connection. Push until the connections snap together.
- Push the quick connect hose connections onto the handle connections. Push until the connections snap together.Pull down moderately to ensure the connections have been made. Cross mounting ensures water flow.
- Connect the hot and cold water line to the hot and cold water inlet of the faucet. Use wrench to tighten. Do not overtighten.
- Do not twist the hose ensures water flow.
Pop-up Drain Installation
-
Preparing the pop-up assembly
Remove the bottom gasket (N)and nut(O)}from the top gasket(L)and pop-up body (M)
Attach these pieces together by pushing the bottom gasket( N) down into the top of the nut (O)and twisting together. -
Installing the pop-up body
Insert the pop-up body (M)into the sink. Ensure that the top gasket(L)rests securely between the top of the sink and the top of the pop-up body (M). -
Securing the pop-up body
From underneath the sink, screw the bottom gasket(N)and nut(O) assembly onto the pop-up body (M) by twisting clockwise until secure .
-
Close the drain and fill the sink with water.
Then check for leaks. If water is leaking from the drain,double check the “N” &“O” components .