HEATROD Elements AESTB 3xx Domestic Immersion Heaters Instruction Manual
- June 17, 2024
- HEATROD Elements
Table of Contents
AESTB 3xx Domestic Immersion Heaters
For further information on the HWA Charter
Membership, please refer to the HWA website
hotwater.org.uk
Fitting Instructions for Immersion Heater Types :
AESTB 3xx, BESTB 3xx, CESTB 3xx, DESTB 3xx, EESTB 3xx,
CKSTF 3xx, CKSTF -340 REW & CETSB 3xx.. ( “xx” denotes immersed length in cm)
3kW Heaters conform to EN 60335-2-73:2003 + A1:06 + A2:09 and are NEMKO
approved.
-
Check that the heater rating label shows the voltage that conforms to your mains supply.
-
Install the heater into the water tank or cylinder using the O-ring or gasket supplied. Use a shaped immersion heater spanner- Stillsons should not be used. The heater may be installed into a tank of any size, suitable to take this heater
when installed in a horizontal manner, the heater must operate below water level, such as a cistern-fed or mains regu- lated tank, if applicable. -
It is essential that the installer checks that the water level within the tank or cylinder is such that the water will al- ways fully cover the heating element by a depth of at least 100mm. Under NO circumstances must the heater be al- lowed to run dry — serious damage may result to the heater in addition to danger of personal injury and damage to property.
-
Check the heater for possible water leakage before moving on to the wiring stage.
See overleaf for schematic wiring diagram.
-
The heater is to be wired with cable having a minimum size of 1.5 sq mm., 909C elastomer insulated HOSBN4-F sheathed cable to BS6500. The heater MUST be fully earthed and wired through a double pole switch having a contact
separation of at least 3mm in accordance with the wiring rules. Ensure all terminal connections are securely made and there are no loose strands. Do not use excessive force when tightening terminals. -
NEMKO approval will only apply to Approved Heaters if the following thermal controls are used :
Thermowatt type : R.T.S-3,, Cotherm TSE. The heater conforms to the EEC Directive BS EN 55014-1:2006+A2:2011 for Electromagnetic compatibility.
Warning : Before making any adjustments within the heater terminal cover, isolate the heater from the mains elec- tricity supply. DO NOT COVER the heater cap.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capa- bilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with this appliance. -
In the event of the manually resettable cut-out within the thermostat operating range, isolate the heater from the mains supply before removing the terminal cover. Investigate and identify the cause for the operation of the cutout, and rectify if possible before manually resetting the device by pressing the small button located on the top of the ther- mostat housing. At the same time, to prevent re-occurrence, it is advisable to turn down the temperature setting on the thermostat to around 55°C. Refer to FAQ’s website.
It must be noted that if the cylinder is also heated by a secondary source such as solar-energy, or by an oil or coal fired boiler producing heat higher than the cut-out pre-set temperature, this can also cause the cut-out to operate. It is not recommended that the thermostat is set higher than 60°C. -
Important : It is not necessary for the heater to be removed to rectify any problems with the thermostat/cut-out. If the fault persists, the device can be replaced. Replacement thermostats can be obtained from the immersion heater manufacture using the details overleaf.
-
Schematic Wiring Diagram, Earth Assembly Diagram and Cable Grip Fitment Details.
COTHERM TSE00187—1 = 10°C, 2 = 25°C, 3 = 40°C, 4 = 55°C, 5 = 70°C (Set just under 5)
Manufactured in the UK.
PLEASE RETAIN THIS LEAFLET FOR FUTURE REFERENCE
IT IS THE INSTALLERS RESPONSIBILITY TO CHECK ALL CONNECTIONS, INCLUDING
FACTORY MADE CONNECTIONS.
Warranty Information
All products carry a standard 12 month parts only warranty. Products that are
deemed faulty can be returned for replacement or credit at any time within
this warranty period. PLEASE SEE OUR WEBSITE FOR FURTHER DETAILS.
For Technical Help or Assistance—Refer to FAQ’s website
www.heatrod.com or
www.heatrodshop.com
Tel: 0161 727 3713 Fax: 0161 727 3733 Email:
technicalsupport@heatrod.com
Environmental Information
Please note this product can be recycled at the end of its life cycle.
If required this product can be returned to Heatrod Elements Limited for
disposal.
Heatrod Elements Ltd. Unit 10 Top Deck, Smethurst lane, Farnworth, Bolton BL4
0AN
Document Ref. MS-014
References
- Hot Water Association: Developing Hot Water
- Heatrod Elements - Heatrod
- Immersion Heaters & Replacement Heating Elements Direct | Heatrod
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>