Ideal Lux Bergen-1 SP1 Pendant Light Instruction Manual
- June 17, 2024
- ideal lux
Table of Contents
Ideal Lux Bergen-1 SP1 Pendant Light
Product Information
Specifications
- Model: Bergen-1 SP1
- Manufacturer: IDEAL LUX s.r.l.
- Country of Origin: Italy
- Website: www.ideal-lux.com
Product Usage Instructions
Important Safety Instructions
Before proceeding with the installation and usage of this lighting fixture,
please read and follow these important safety instructions
- The installation of this appliance must be carried out by qualified personnel.
- Always disconnect the power supply before starting any installation or maintenance work.
- Avoid looking directly at the light source.
- Do not attempt to replace the LED light source as they are not user-replaceable.
- If the lamp does not turn on, replace the fuse.
Installation Process
- Follow the assembly instructions in the numerical order provided in the manual.
- Ensure that the lighting fixture is installed by a qualified electrician only.
- Use appropriate fixing accessories for different materials and ensure compliance with regulations.
- Check for any damage to the external electrical cable and replace it only with parts approved by the manufacturer or a qualified electrician.
Electrical Safety Classes
The product is classified into different electrical safety classes. Please
refer to the following for guidance:
- Class I: Requires mandatory grounding for electrical safety.
- Class II: Does not require grounding due to double insulation or reinforced insulation.
- Class III: Operates at very low voltage (<50V) and does not require grounding.
Protection Ratings
The product has protection ratings against solid particles and moisture.
Here are the details:
- Protected against solid particles larger than 50 mm, 12 mm, 2.5 mm, and 1 mm based on specified ratings.
- Fully protected against dust ingress.
FAQ
Q: Can I replace the LED light source myself?
A: No, the LED light source is non-replaceable and should not be
disassembled. If the light is not working, consider replacing the fuse.
Q: Do I need to ground the lighting fixture during installation?
A: Yes, for Class I fixtures, grounding is mandatory to ensure electrical
safety.
Q: What should I do if I notice damage to the external electrical cable?
A: If you observe any damage to the external cable, it should only be
replaced with approved parts by the manufacturer or a qualified electrician.
Electrical Safety Instruction
ASSEMBLY INSTRUCTION
FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION. THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN.
SAFETY INSTRUCTIONS
- This fitting is produced and tested in accordance with the strictest European safety standards (EN 60.598-1).
- This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
- As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
- If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
- Always isolate power before commencing installation, maintenance or repair.
- The luminaire contains certain parts which can be very hot.
- Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
- Always tighten the screws firmly to avoid contact problems.
- This fitting should only be installed indoors.
- Luminaires are not suitable for recessed on normally flammable surfaces.
- Luminaire is not suitable for direct mounting on normal flammable surfaces.
- This fitting is only suitable for fixing to the ceiling.
- This fitting is only suitable for fixing to the wall.
- The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
- Only use lamps that do not exceed the maximum specified wattage.
- Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
- Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing them.
- Cracked or broken safety glass has to be replaced immediately. Use only manufacturer-approved parts complying with regulations.
- Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
- This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
- Class I Electrical safety is guaranteed by the main insulation and an additional protective conductor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
- Class Il Electrical safety is guaranteed by the main insulation and double or reinforced insulation. Earthing not necessary.
- Class Ill Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
- Not protected.
- Protected against solid objects greater than 50 mm.
- Protected against solid objects greater than 12 mm.
- Protected against solid objects greater than 2,5 mm.
- Protected against solid objects greater than 1mm.
- Dust protected.
- Totally protected against dust infiltration.
- Not protected.
- Protected against vertically falling water drops.
- Protected against water drops falling with a maximum angle of 15° to the vertical axis.
- Protected against rain.
- Protected against splashing water.
- Protected against water jets.
- Protected against strong water jets.
- Protected against temporary immersion.
- Protected against prolonged immersion.
- Luminaire is not suitable for covering with thermally insulating material.
- Caution, risk of electric shock.
- Do not stare at the operating light source.
IDEAL LUX s.r.l. Via Taglio Destro 32 30035 Mirano (VE) Italy www.ideal-
lux.com
IDEAL LUX Warehouse Via delle Industrie, 8/D 30036 Santa Maria di Sala
(Venezia) 8.00 – 12.00 / 13.30 – 17.00
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>