HAM PARTS OLI IP 16 Universal Controller User Manual

: June 17, 2024
: HAM PARTS

Table of Contents

Front panel description
Rear panel description
Parameters
Connection and connectors description
Jumper settings
Remote Control
QUICK setup
Product details
Documents / Resources

OLI IP 16 MANUAL HAM PARTS OLI IP 16 Universal
Controller manual
CTRL

This is manual page for OLI IP 16 controller. This box is directly designed for our K9AY++/4-WAY beverage system and also 7ANT switch controller.

Front panel description

HAM PARTS OLI IP 16 Universal Controller - Figure 1

QRO.cz | hamparts.shop

LED – Status LED
– PTT – PTT information
– ON – controller is ON

Rear panel description

HAM PARTS OLI IP 16 Universal Controller - Figure 2 1 – LAN
2 – USB
3 – DB25 female
QRO.cz | hamparts.shop

LAN
– 10/100 Mbit LAN with DHCP
USB
– USB port for FW upload
DB25 female
– outputs + PTT + DC input

Parameters

Universal 16 outputs with + voltage or GND outputs
DEFAULT CONFIGURATION with + voltage outputs (TBD drivers)
Output current: max. 500mA per output, 700 mA total
Input voltage max. 24 V DC, 1 A
Voltage drop for TBD driver typ. 0.2 V for +12 V input and 0.7 V including fuse
Voltage drop for ULN driver typ. 0.8 V fro +12 V input
Output voltage for positive driver is input voltage minus abt 0.7 V
LED indication: ON and PTT
LAN 10/100 MBit with ﬁlter and protection
ONLY DHCP IP address – not static.

Connection and connectors description

There is DB25 female connector with PTT in, power supply and output pins. This controller could have positive or negative output drivers. It means when PIN is switched remotely ON, the supply voltage is switched to this output PIN (for positive driver TBD) or switched to ground (for negative driver ULN). There is also internal electronic fuse (short protection).
You can directly connect any of your devices, relays, preamp etc. Output pins could work as simply ON/OFF switch and also could be grouped together in 1-of-X. PTT IN could work as a hot switch protection – disable switching while PTT is in transmitting mode. PIN description
OLI IP 16

D-SUB25 PIN	PIN .
1	+ DC IN*
14	+ DC IN*
2	OUT1
15	OUT 2
3	OUT 3
16	OUT 4
4	OUT 5
17	OUT 6
5	OUT 7
18	OUT 8
6	OUT 9
19	OUT 10
7	OUT 11
20	OUT 12
8	OUT 13
21	OUT 14
9	OUT 15
22	OUT 16
10	GND
23	GND
11	GND
24	GND
12	+ DC IN*
25	+ DC IN*
13	PTT IN
shield	GND

remote connector D-SUB 25 female *+ DC IN – supply voltage
– up to 26V DC, max. 1A
OUT – jumper set
– output depends on driver
– Max. 0.5A/PIN, max. 0.7/ALL, max. 26V DC
– see jumpers settings
QRO.cz | hamparts.shop

Jumper settings

There is one group of jumpers. These jumpers must be set to right position. This depends on output drivers. Could be positive TBD (DEFAULT conﬁguration) or negative ULN.
OLI IP 16
jumper for output drivers QRO.cz | hamparts.shop
RELAY CONNECTION vs OUTPUT DRIVER![HAM PARTS OLI IP 16 Universal Controller

Figure 5](https://manuals.plus/wp-content/uploads/2024/02/HAM-PARTS-OLI- IP-16-Universal-Controller-Figure-5.png) QRO.cz | hamparts.shop

Remote Control

OLI IP 16 could be controlled by the three basic ways. If you want to know more about REMOTE SYSTEM, please read our technical articles.
REMOTE CONTROL OPTIONS HAM PARTS OLI IP 16 Universal Controller - Figure
6 QRO.cz | hamparts.shop

CLASSIC User Interface (UI)
– There are UI with the similar look as the HW controllers. You can use this web page UI to control outputs by clicking on buttons, you can change labels, colour, font size etc.
BEAM MAP UI
– This is UI with automatically generated beam map from your location. There are preconﬁgured templates for different HW (K9AY, 7ANT, 4SQ, 8 Circle etc.). You can change antenna (port) direction, antenna beam width, colours etc.
OTHER
– You can use your own code, NodeRed, Stream Deck etc. Please, contact us for API details.

UI examples
BEAM MAP example UI HAM PARTS OLI IP 16 Universal Controller - Figure
7 QRO.cz | hamparts.shop
16 OUTPUT example UI QRO.cz | hamparts.shop

QUICK setup

Mike DM5XX has prepared Entry Point and Easy Assistant pages. This is the best way to go, see all possibilities of our UIs.
Please, start with ENTRY POINT manual page
QUICK UI setup link is there: EASY ASSIST
Please, follow our YouTube channel
IMPORTANT NOTE: We recommend a VPN while using remote access from outside your network in general.

Product details

Included in package
Controller assembled and tested
DB25 male connector with cover
2pcs ULN drivers – image

Box dimensions (mm)	75x85x48 mm – al box
Weight brutto (kg)	0.25 kg

Manufacturer:
Ing. Jan Sustr
ID 05476356, VAT CZ8407024780
Palachova 1777/7, 591 01 Žďár nad Sázavou, Czech republic, Europe
General instructions:
Please also read general instructions before handling the product.
European Union Declaration of Conformity
Manufacturer Ing. Jan Šustr (QRO.cz): ID 05476356, VAT CZ8407024780
Palachova 1777/7, 591 01 Žďár nad Sázavou, Czech republic, Europe
declares that the assembled product: OLI IP 16
is compatible with the relevant Union harmonisation legislation directives: EMC Directive 2014/30/EU
ČSN EN 61000-6-3 ed. 2
ČSN EN 61000-6-1 ed. 2 (333432)
On behalf of Ing. Jan Šustr (QRO.cz)
Ing. Jan Šustr, CEO
14th June 2023

Tag: manual, controller, oli ip, remote, oli ip 16, oli ip16
Previous article

Next article
RELATED ARTICLES
Remote Controllers by QRO.cz with code by DM5XX
Remote Controllers by QRO.cz with code by DM5XX
RELATED PRODUCTS
OLI IP 12
2021 – 2023 © hamparts.shop. All Rights Reserved.
Designed by Lucino

Documents / Resources

| HAM PARTS OLI IP 16 Universal Controller [pdf] User Manual
OLI IP 16 Universal Controller, OLI IP 16, OLI IP 16 Controller, Universal Controller, Controller
---|---