Zhizun International KUS600 Series Ultrasonic Distance Sensor Instructions
- June 17, 2024
- Zhizun International
Table of Contents
Zhizun International KUS600 Series Ultrasonic Distance Sensor Instructions
Features
- Non-contact measurement
- PVDF casing forcorrosion environment
- Low power consumption solution
- Various output options, wide voltage power supply
Drawings of the sensor
Sensor picture
Drawing of the sensor (unit mm)
Electrical connections
| Cable color | PIN No | Definition | Note |
|---|---|---|---|
| Red | 1 | Power supply | 3.3V~24V |
| Black | 2 | GND | |
| Yellow | 3 | Analogue output | Low power version hasn’t analog output |
| Blue | 4 | RS485A+ | |
| Green | 5 | RS485B- |
Parameter
| General parameters | Mechanical Properties | |
|---|---|---|
| Model No | KUS600 | Connection |
| Detection Range1 | 0.6~5m | **** IP grade |
| Blind zone | 0～0.6m, | |
| Ranging resolution | 1mm | Weight |
| Measurement accuracy | ≤1%F.S | Single package |
| Transducer frequency | 220 kHz | Single gross weight |
| Response Time | approx. 10 ms | |
| Beam Angle | 7°±2 | |
| Temp. Compensation | inside/outside/fixtemp |
Electrical Parameters
Operating Voltage| 3.3~24VDC ripple 10 %SS
Power consumption| ≤ 20mA active period, ≤0.3mA during sleep time,≤5mA
detection status
Circuit Protection| short-circuit protection, overload protection
**** Output| Digital Output| RS485
Analogue Output| 4～20mA/ 0～3.3V/ 0～5V
Switch Output| NPN/PNP
Ambient Environment
Operating Temp.| -25℃-+70℃(-40~85℃, -55~125℃, etc, customizable)
Storage Temperature| -40℃-+85℃
Description of Sensor Functions
Analogue output
Liner output and Program diagrams
The analog output can be set through RS485 interface, the setting procedure is as follows,
Step 1: connect the sensor to the computer through serial port debugging
assistant or Modbus debugging assistant.
Step 2: set a near distance point through RS485
Step 3: set a far distance point through RS485
Step 4: set the output voltage or current of the near distance point
Step 5: set the output voltage or current of the far distance point
Step 6: set the analog output to the switch characteristic option
Step 7: set the analog output to a linear output or switch output option
Step 8: reset the sensor to make the new parameters take effect
Switch output
There are 8 different functions
- Default window mode normally open
- Default window mode normally closed
- Default single point switch mode normally open
- Default single point switch mode normally closed
- Default single point hysteresis mode normally open
- Default single point hysteresis mode normally closed
- Default object detection mode normally open
- Default object detection mode normally closed
8 output logic diagrams of switch output
Digital output: RS485
Communication protocol is Modus-RTU.
For more information please contact us for the software engineering guide.
Installation conditions
If the sensor is installed at the environment temperature fall below 0℃, it
should do well on the protective measures.
In case of direct mounting of the sensor in a through hole using the nuts, it
has to be fixed at the middle of the housing thread
Order information
| Model No. | Output | Max range | Description |
|---|---|---|---|
| KUS600 | Switch output | 5m | 1.2m connection cable |
| Analog output | 5m | 1.2 connection cable | |
| RS485 | 5m | 1.2 connection cable |
Contact us
Xi’an Zhizun International Trade CO., Ltd.
Tel: +86-29-87858956
E-mail: contact@top1sensor.com
Getting more info & supports from http://www.top1sensor.com
Tel: 0086-029-87858956
Email: contact@top1sensor.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>