0808 e-commerce DC402 4K Digital Camera User Manual

0808 e-commerce DC402 4K Digital Camera

Product Specifications

• Video Resolution: 4K/2.7K/1080P FULL HD/720P HD/480PVGA

• Image Resolution: 48M/44M/36M/24M/20M/16M/12M/10M/7M-Wide/5M/3M/2M-Wide

• Memory Card: Support Micro SD card (4GB to 256GB Class10 is recommended)

• File Format: JPG, AVI

• Taking Photos: Single/Continuous shooting/2s timer/5s timer
  /10s timer

• Electronic Zoom: 16X

• USB Port: Type-C

• Display: 2.8 inch Screen

• Battery: Rechargeable Li-Ion Battery

• Focal Length: f=7.36mm

• Aperture: F/3.2

• Power Save: Auto power off in 1Min/3Mins /5Mins

• Operating System Requirements: Windows XP, Windows Vista,
  Windows 7, Windows 8, Windows 10, Mac 10.2

How to Insert and Remove the Battery

1. Open the battery cover.
2. Insert the end with electrical contacts until it locks into place.
3. Close the battery cover.
4. To remove the battery, push the battery lock.

How to Charge the Camera

1. Use the Type-C cable and charger included in the package to charge.
2. When the camera indicator light is red, it means the camera is charging.
3. When the camera light goes out, it means the camera is fully charged.
4. Note: For the first time, please use it after fully charged.

How to Insert and Remove Micro SD Card

1. Open the battery cover.
2. As shown by the illustration, face the card’s metal contacts side toward you and insert it until it locks in place.
3. Close the battery cover.
4. Caution: The camera supports 4-256GB Micro SD card, Class10 isrecommended. We do not recommend using U3 level card.
5. When the Micro SD card is used for the first time, please format it in the camera.

Important Battery Safety Tips

For your better experience with this product, please pay attention to the following safety tips
If the battery pack is mishandled, the battery pack can burst, cause a fire or even chemical burns.Observe the following cautions.

• Do not disassemble.
• Do not crush and do not expose the battery pack to any shock or force such as hammering,dropping or stepping on it.
• Do not short circuit and do not allow metal objects to come into contact with the battery terminals.
• Do not expose to high temperature above 60°C(140°F)such as in direct sunlight or in a car parked in the sun.
• Do not incinerate or dispose of in fire.
• Do not handle damaged or leaking lithium ion batteries.
• Be sure to charge the battery pack using a genuine battery charger or a device that can charge the battery pack.
• Keep the battery pack out of the reach of small children.
• Keep the battery pack dry.
• Replace only with the same or equivalent type recommended by seller.
• Dispose of used battery packs promptly as described in the instructions.

Introduction of Camera Parts

Product Specifications

How to Insert and Remove the Battery

1. Open the battery cover
   

2. Insert the end with electrical contacts until it locks into place

3. Close the battery cover
   

4. Please push the battery lock to remove the battery

How to Charge the Camera

1. .Please use the Type-C cable and charger included in the package to charge.
   

2. When the camera indicator light is red,it means the camera is charging.

3. When the camera light goes out,it means the camera is fully charged.

4. Please note:For the first time,please use it after fully charged.

How to Insert and Remove Micro SD Card

1. Open the battery cover

2. As shown by the illustration, face the card’s metal contacts side toward you and insert it until it locks in place

3. Close the battery cover

4. Please caution: The camera supports 4-256Gb Micro SD card, Class10 is recommended,we do not recommend using U3 level card. 5.When the Micro SD card is used for the first time,please format it in the camera.

How to Format a Memory Card

1. In the still image mode,press the “Mode” button 3 times to enter the system setting interface and select the“Format”option.
2. Press “OK” to confirm formatting.
3. Press the mode button again to exit the system settings page.

Introduction to Camera System Settings

1. Press the mode button 3 times in the still image mode to enter the still image system settings.
2. After the setting is completed, please press the Mode button to exit the system setting.

Introduction of still image mode

How to Take Still Image

1. Please make sure the camera is in still image mode
   (The camera defaults to still image mode when turned on)

2. Press the shutter button halfway down to focus, When the image is in focus, The focus frame in the screen will turn green.

3. Press the shutter button fully down to shoot an image.

How to play back and delete still image that have been taken

1. Press the mode button 2 times in the still image mode to enter the playback mode
2. Select an image by pressing Left and right keys
3. If you want to delete the photo,please press the down button, this is the shortcut delete key
4. After viewing the photos,please press the mode button twice to exit the playback mode

Introduction to the Still Image mode menu settings

1. Press the menu button in still image mode to enter the image menu settings.
2. .After the setting is completed,please press the menu button to exit the image menu setting.

Introduction to video recording mode

How to shoot video

1. Please make sure the camera is in video recording mode (After turn on camera please press the mode button once to enter video recording mode)
2. Press the shutter button to start/end video recording
3. Press OK button to pause/resume video recording

How to Play Back and Delete Recorded Videos

1. Please press the MODE button once to enter playback mode (when the camera is in video recording mode)
2. Select an video by pressing left and right keys.
3. If you want to delete the video, please press the down button, this is the shortcut delete key.
4. After viewing the video, please press the mode button twice to exit the playback mode.

Video recording mode menu settings introduction

1. Press the MENU button in video recording mode to enter the video menu settings.
2. After the setting is completed,please press the MENU button to exit the video menu setting.

How to download still image/video files to computer

1. When the camera is turned on, use the Type-C cable (in the package) to connect the computer
2. After the connection is completed, a dialog box will pop up randomly on the camera screen
3. Please select MSDC, then you can download the files from the camera to your computer
4. After downloading, please remove the Type-C cable and the camera will exit MSDC mode

How to use camera as webcam

1. Please use the Type-C cable (in the package) to connect the computer with the camera when the camera is turned on.
2. After the connection is completed, a dialog box will pop up randomly on the camera screen.
3. Please select “PC camera” , then you can use the camera as webcam on the computer.
4. After using, please remove the Type-C cable and the camera will exit webcam mode.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>