HITEC HS-7966HB Series Micro Digital Servos Instruction Manual

June 17, 2024
HiTEC

www.hitecrcd.com
HS-7966HB Series Micro Digital Servos
Instruction Manual

HS-7966HB Series Micro Digital Servos

Servo Programming Instruction for
New Hitec HS-SOXX Series Micro Digital Servos
Thank you for purchasing Hitec HS-50XX series micro digital servos!
Please peruse the nformation below for proper programming of the servos.
For Programming HS-50XX Digital Feather/Micro Servos
(HS-50XX series : Currently HS-5055MG, 5056MG, 5065MG, 5082MG and 5085MG)

  1. New programming function(Over oad protect on setting) has been added to Hitec’s new digital feather / micro servos stated above.
  2. The new function is NOT available n conventional HS-5XXX and HS-6XXX digital servos.
  3. The new function can be programmed by Hitec Servo Programmer(HFP-20) and Hitec PC Link Programmer(HPP-21).
  4. For more detailed informat on, please refer to the manual of HFP-20 and HPP-21.
  5. Important Note: This new function (Overload protection setting) CANNOT be programmed by HFP-10, prev ous version of Hitec Servo Programmer.

Programmer| Function| Conventional
HS-5xxx / 6xxx
Digital Servos| HS-50xx
Digital Micro
Servos
---|---|---|---
HFP – 20 User| HFP – 10 User| Servo Test| Yes| Yes
RX Pulse & Voltage Measure| Yes| Yes
Reset| Yes| Yes
Dead Band setting| Yes| Yes
Change Rotation (CW / CCW)| Yes| Yes
Servo Speed| Yes| Yes
Fail Safe(On/Off)| Yes| Yes
EPA / Fail Safe Position| Yes| Yes
| Overload Protection*| No| Yes

*Overload protection : This funct on is to protect the servo(HS-50XX servos) from the overload condition. Once the servo is overloaded for a certain period of time, the motor output will be reduced to the evel that the user programmed to the servo. Please note that this function s deactivated (off) in factory setting.

Servo Programming Instruction for
New Hitec HS-7XXX Series Digital Servos
Thank you for purchasing Hitec HS-?XXX series digital servos!
Please peruse the information below for proper programming of the servos.
For Programming HS-7XXX Digital Servos
(HS-?XXX series: Current y, HS-7955TG, HS-7985MG, HS-7965MG, HS-7966HB and HS- 7975HB)

  1. New programming funct ons(Resolution mode setting and Overload protection sett ng) have been added to Hitec HS-?XXX series.
  2. These new functions are NOT available in Hitec HS-5XXX and HS-6XXX digital servos.
  3. These new functions can be programmed by Hitec Servo Programmer(HFP-20) and Hitec PC Link Programmer(HPP-21) as well.
  4. For more detailed information, please refer to the manual of HFP-20 and HPP-21.
  5. Important Note: These two new functions(Resolution mode setting and Overload protection sett ng) CANNOT be programmed by HFP-10, previous version of Hitec Servo Programmer.

Programmer| Function| Conventional
HS-5xxx / 6xxx
Digital Servos| HS-7xxx
Digital
Servos
---|---|---|---
HFP – 20 User| HFP – 10 User| Servo Test| Yes| Yes
RX Pulse & Voltage Measure| Yes| Yes
Reset| Yes| Yes
Dead Band setting| Yes| Yes
Change Rotation (CW / CCW)| Yes| Yes
Servo Speed| Yes| Yes
Fail Safe(On/Off)| Yes| Yes
EPA / Fail Safe Position| Yes| Yes
| Overload Protection*| No| Yes
Resolution Mode Setting”| No| Yes

*Overload protection:* This function is to protect the servo(HS-?XXX servos) from the overload condition. Once the servo s over oaded for a certain per od of time, the motor output will be reduced to the level that the user programmed to the servo. Please note that this function is deact vated (off) n factory setting.
Resolution mode setting:** There are two resolution modes(High and Normal) in HS-?XXX servos. Factory default is set at “High” resolution, and servo travel will be 120 degrees.
If the user needs to widen the servo travel, the user may select “Norma ” resolut on so that the servo travel can be widened to the maximum of 180 degrees.

www.hitecrcd.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals