IRONTON 58643 Wireless Driveway Alert Owner’s Manual

IRONTON 58643 Wireless Driveway Alert Owner’s Manual

WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.

Thank you very much for choosing an Ironton™ product!

For future reference, please complete the owner’s record below:

Serial Number/Lot Date Code: __
Purchase Date: __

Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it.

This wireless driveway alert is designed for certain applications only.
Northern Tool and Equipment is not responsible for issues arising from modification or improper use of this product such as an application for which it was not designed. We strongly recommend that this product not be modified and/or used for any application other than that for which it was designed.

For technical questions, please call 1-800-222-5381

Intended Use

The Ironton wireless driveway alert system gives you protection and peace of mind by notifying you audibly as soon as anyone enters your driveway. This system operates conveniently on batteries, so no electricity is required to install it. It includes an outdoor motion sensor and an indoor alarm. When motion is detected, the indoor receiver sounds an alert.

Packaging Contents

• Part A (3)
• Part B (2)
• Part C (6)
• Receiver (1)
• Sensor (1)
• Hardware bag (1)

Technical Specifications

• This alarm system complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired operation.

FCC ID: 2AA9QJR-178

Important Safety Information

WARNING

• Read and understand all instructions. Failure to follow all instructions may result in serious injury or property damage.
• The warnings, cautions, and instructions in this manual cannot cover all possible conditions or situations that could occur. Exercise common sense and caution when using this product. Always be aware of the environment and ensure that the product is used in a safe and responsible manner.
• Do not allow persons to operate or assemble the product until they have read this manual and have developed a thorough understanding of how it works.
• Do not modify this product in any way. Unauthorized modification may impair the function and/or safety and could affect the life of the product. There are specific applications for which the product was designed.
• Use the right tool for the job. DO NOT attempt to force small equipment to do the work of larger industrial equipment. There are certain applications for which this equipment was designed. This product will be safer and do a better job at the capacity for which it was intended. DO NOT use this equipment for a purpose for which it was not intended.
• Industrial or commercial applications must follow OSHA requirements.

WARNING

WORK AREA SAFETY

• Inspect the work area before each use. Keep work area clean, dry, free of clutter, and well-lit.
  Cluttered, wet, or dark work areas can result in injury. Using the product in confined work areas may put you dangerously close to cutting tools and rotating parts.

• Do not use the product where there is a risk of causing a fire or an explosion; e.g., in the presence of flammable liquids, gases, or dust. The product can create sparks, which may ignite the flammable liquids, gases, or dust.

• Do not allow the product to come into contact with an electrical source. The product is not insulated and contact will cause electrical shock.

• Keep children and bystanders away from the work area while operating the tool. Do not allow children to handle the product.

• Be aware of all power lines, electrical circuits, water pipes, and other mechanical hazards in your work area. Some of these hazards may be hidden from your view and may cause personal injury and/or property damage if contacted.

CAUTION

ALARM SYSTEM USE AND CARE

• Do not force the alarm system. Products are safer and do a better job when used in the manner for which they are designed. Plan your work, and use the correct product for the job.
• Check for damaged parts before each use. Carefully check that the product will operate properly and perform its intended function. Replace damaged or worn parts immediately. Never operate the product with a damaged part.
• Do not use a product with a malfunctioning switch. Any power tool that cannot be controlled with the power switch is dangerous and must be repaired by an authorized service representative before using.
• Disconnect the power/air supply from the product and place the switch in the locked or off position before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally.
• Store the product when it is not in use. Store it in a dry, secure place out of the reach of children. Inspect the tool for good working condition prior to storage and before re-use.
• Use only accessories that are recommended by the manufacturer for use with your product. Accessories that may be suitable for one product may create a risk of injury when used with another tool. Never use an accessory that has a lower operating speed or operating pressure than the tool itself.

Specific Operation Warnings

WARNING

• Position batteries in proper polarity and do not install batteries of different types, charge levels, or capacities together.
• Verify that the installation surface has no hidden utility lines before drilling or driving screws.
• Do not install the receiver in a location that will get wet or directly exposed to the elements.
• The receiver is not intended to be weather-resistant.

Main Parts of Alarm System

Installing Instructions

WARNING

• Position batteries in proper polarity and do not install batteries of different types, charge levels, or capacities together.
• Verify that the installation surface has no hidden utility lines before drilling or driving screws.
• Do not install the receiver in a location that will get wet or directly exposed to the elements.
• The receiver is not intended to be weather-resistant.

1. Take the following factors into consideration when choosing the install location of the sensor:
   A. The passive infrared sensor detects heat. Avoid aiming it toward areas that produce heat (heater vents, windows where the sun hits, or outdoor spotlights).
   B. The sensor needs to be mounted at least 3 feet above the ground. If placing under garage eaves, be sure that the sensor is not blocked by the roof facial board.
   C. If placing more than 8 feet high, the sensor should be aimed downward so that it is pointed toward the area being monitored.
   D. Obstructions may reduce the receiving range.

2. Mount the sensor to a flat surface with the hardware (3).

3. Place the receiver within 400 feet of the sensor.

4. An optional 6 volt, 200mA power adapter (not included) can be used to power the receiver instead of batteries.

Before Each Use

WARNING

• Inspect the general condition of the alarm system.
• Check for leaking, swollen, or cracked batteries.
• Check for loose hardware.

Operating Instructions

1. The power switch has three settings:

   • OFF: Power is off.
   • HI: A loud beep (92dB) and the LED will flash when motion is detected.
   • LOW: A short beep (80dB) and the LED will flash when motion is detected.

2. Slide the power switch on the receiver to the HI setting. Allow 30 seconds for a warm-up. Two short beeps will sound, indicating the alarm is working.

3. Once the alarm is working properly, choose the HI setting or the LOW setting, as needed.

After Each Use

• Wipe the external surfaces of the product with a clean cloth.
• Replace the batteries in the receiver and/or sensor when the low battery LED indicator lights.

Troubleshooting

sensor or the receiver.
There are obstacles between the sensor and the receiver.| Check for any possible obstructions and remove them.

Parts Diagram

Parts List

Replacement Parts

• For replacement parts and technical questions, please call Customer Service at 1-800-222-5381.
• Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequence.
• When ordering parts, the following information will be required: item description, item model number, item serial number/item lot date code, and the replacement part reference number.
• The distributor reserves the rights to make design changes and improvements to product lines and manuals without notice.

Limited Warranty

Northern Tool and Equipment Company, Inc. (“We” or ”Us”) warrants to the original purchaser only (”You” or ”Your”) that the Ironton product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions. There are no other warranties, express or implied, including the warranty of merchantability or fitness for a particular purpose. If the product does not comply with this limited warranty, Your sole and exclusive remedy is that We will, at our sole option and within a commercially reasonable time, either replace the product or product component without charge to You or refund the purchase price (less shipping). This limited warranty is not transferable.

Limitations on the Warranty

This limited warranty does not cover: (a) normal wear and tear; (b) damage through abuse, neglect, misuse, or as a result of any accident or in any other manner; (c) damage from misapplication, overloading, or improper installation; (d) improper maintenance and repair; and (e) product alteration in any manner by anyone other than Us, with the sole exception of alterations made pursuant to product instructions and in a workmanlike manner.

Obligations of Purchaser

You must retain Your product purchase receipt to verify date of purchase and that You are the original purchaser. To make a warranty claim, contact Us at 1-800-222-5381, identify the product by make and model number, and follow the claim instructions that will be provided. The product and the purchase receipt must be provided to Us in order to process Your warranty claim. Any returned product that is replaced or refunded by Us becomes our property. You will be responsible for return shipping costs or costs related to Your return visit to a retail store.

Remedy Limits

Product replacement or a refund of the purchase price is Your sole remedy under this limited warranty or any other warranty related to the product. We shall not be liable for: service or labor charges or damage to Your property incurred in removing or replacing the product; any damages, including, without limitation, damages to tangible personal property or personal injury, related to Your improper use, installation, or maintenance of the product or product component; or any indirect, incidental or consequential damages of any kind for any reason.

Assumption of Risk

You acknowledge and agree that any use of the product for any purpose other than the specified use(s) stated in the product instructions is at Your own risk.

Governing Law

This limited warranty gives You specific legal rights, and You also may have other rights which vary from state to state. Some states do not allow limitations or exclusions on implied warranties or incidental or consequential damages, so the above limitations may not apply to You. This limited warranty is governed by the laws of the State of Minnesota, without regard to rules pertaining to conflicts of law. The state courts located in Dakota County, Minnesota shall have exclusive jurisdiction for any disputes relating to this warranty.

Distributed by:
Northern Tool & Equipment Company, Inc.
Burnsville, Minnesota 55306
www.northerntool.com
Made in China

References

• northerntool.com
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>