GoKWh 48V 100Ah LiFePO4 Battery User Manual
- June 16, 2024
- GoKWh
Table of Contents
- 48V 100Ah LiFePO4 Battery
- Important Safety Instructions
- SCOPE OF APPLICATION
- TECHNICAL PARAMETER
- APPEARANCE AND STRUCTURAL DIMENSIONS
- RS485-A、RS485-B Description
- LED DISPLAY
- DESCRIPTION OF COMMUNICATION AND PC SOFTWARE
- DIAL SWITCH ADDRESS SETTING
- STORAGE ANDOTHERS
- WARRANTY
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
USER MANUAL
48V 100Ah
LiFePO4 Battery
48V 100Ah LiFePO4 Battery
Dongguan GoKWh Technology Co., Ltd.
Version – 2023
Important Safety Instructions
Please save these instructions.
DISCLAIMER
Please read all specifications, usage, storage conditions, and warnings on this
document before use. Always adhere to our handling and usage directions for
this battery pack. Misuse of batteries can cause the battery to malfunction,
degrade and reduce its capacity or life expectancy, overheat, explode, or
become a fire hazard. Customers are responsible for the proper use and storage
of this battery pack which is outlined on this document. If at any point, the
battery excessively overheats, leaks, etc, or does not function as stated, or
is visibly damaged; DO NOT USE. Please contact our support team for further
assistance.
Note (1) :
The customer is requested to contact GoKWh Technology Co.,Ltd. in advance, if
and when the customer needs other applications or operating conditions than
those described in this document. Additional experimentation may be required
to verify performance and safety under such conditions
Note (2) :
GoKWh Technology Co.,Ltd. will take no responsibility for any accident when
the cell is used under other conditions than those described in this Document.
Note (3):
GoKWh Technology Co.,Ltd. will inform, in a written form, the customer of
improvement(s) regarding proper use and handling of the cell, if it is deemed
necessary.
WARNINGS
- DO NOT immerse the battery in water or allow it to get wet.
- DO NOT use or store the battery near sources of heat such as a fire or heater.
- DO NOT reverse the positive (+) and negative (-) terminals.
- DO NOT connect the battery directly to wall outlets or car cigarette-lighter sockets without proper charging equipment. DO NOT allow exposed ends of cables connected to opposite terminals to touch.
- DO NOT put the battery into a fire or apply direct heat.
- DO NOT use the battery if the battery casing has been pierced, broken, cracked, or otherwise visibly damaged. DO NOT forcibly open the battery casing for any reason.
- Avoid severe physical shock. Do not throw the battery or heavily strike the battery in any way. Do not put excessive pressure or step on the battery.
- Never solder anything directly to the battery terminals.
- DO NOT attempt to disassemble or modify the battery in any way.
- DO NOT place the battery in a microwave oven or pressurized container.
- DO NOT use the battery in combination with primary batteries(such as dry-cell batteries) or batteries of different capacity, type or brand.
- DO NOT use the battery if it gives off an odor, generates heat, becomes discolored or deformed, or appears abnormal in any way. If the battery is in use or being recharged, remove it from the device or charger immediately and discontinue use.
- DO NOT use or store the battery where is exposed to extremely hot, such as under window of a car in direct sunlight in a hot day. Otherwise, the battery may be overheated. This can also reduce battery performance and/or shorten service life.
- If the battery leaks and electrolyte gets in your eyes, do not rub them. Instead, rinse them with clean running water and immediately seek medical attention. If left as is, electrolyte can cause eye injury.
SCOPE OF APPLICATION
This product specification describes the product performance index, maintenance and danger warning of the energy storage battery pack produced by Dongguan GoKWh Technology Co., Ltd. This User Manual is applicable to 48V 100Ah/200Ah/300Ah Battery. If users need more technical support or any other requirements, they can contact the customer service center or technical center of GoKWh Technology Co., Ltd.
TECHNICAL PARAMETER
Model | 48100 | Remark |
---|
Basial
Cell Type| LiFePO4 Prismatic|
Dimensions| 44O43O222mm|
Combination Method| 16S1P|
Weight| 48kg|
Case Material| Cold Rolled Steel(SPCC)|
Electrical| |
Typical Capacity| 1OOAH| at25℃,O.2C Discharging
Minimum Capacity| ≥95Ah
Nominal Voltage| 51.2V|
Nominal Energy| 512OWh|
Discharge Cut-off Voltage| ≥4OV|
Charging Cut-off Voltage| ≤58.4V|
Internal Impedance| ≤6OmΩ| Under 2O±5℃ Environment Tempera- ture , the Usage
Frequency of Fully Charge( 1KHz) , Use AC Internal Imped-ance test machine to
test
Recommend Max Charging Current| ≤5OA| Ampere-meter ,Maximum allowable charging
current of the battery pack
Max Discharging Current| ≤1OOA| Maximum discharge current allowed by the
battery pack
Standard Charge Current| 2OA|
Standard Discharge Current| 4OA|
Internal Resistance| ≤3O mΩ|
Performance
Cycle Life| ≥6OOO Cycles|
Service Life| 1O Years|
Protection| IP2O, Built-in BMS|
Temperature Range
Charge| O~45°C (32~113°F)|
Discharge| -2O~6O°C (-4~14O°F)|
Storage| -2O~25°C (-4~77°F)| Recommend(25±3℃);≤9O%RH storage moisture range.
APPEARANCE AND STRUCTURAL DIMENSIONS
There shall be no such defect as scratch, bur and other mechanical scratch, and the connector should be no rust dirt. The structure and dimensions see attached drawing of the product.
1 | Positive Terminal | 7 | On-off Switch |
---|---|---|---|
2 | Negative Terminal | 8 | Main Box |
3 | Handle | 9 | Front Cover |
4 | Dial Switch | 1O | Box Cover |
5 | Battery Indicator Light | 11 | LED Display |
6 | Communication Interface RS485/CAN |
RS485-A、RS485-B Description
Communication with host computer
RS485- using 8P8C vertical RJ45 socket
RJ45 Pin| Definition Description
1、8| RS485-B
2、7| RS485-A
3、4、5、6| GND
LED DISPLAY
Start running: LED starts from 16.66% power lamp
Table 1 LED working status indication
Table 2 Description of capacity indication
Description of LED flashing: Flashing 1, on for 0.3s, off for 3.7s; Flashing 2,
on for 0.5s, off for 0.5s; Flashing 3, on for 0.5s, off for 1.5s.
6 SET THE RS485 AND CANBUS PROTOCOLS OF THE BMS TO THE INVERTER THROUGH
THEUPLCD DISP LAYSCREEN
Select Pack Set option
Select the protocol type that needs to be set, namely RS485 or CANBUS
Set the corresponding protocol type
Select the corresponding protocol using the DOWN button
Click the Enter button to select
DESCRIPTION OF COMMUNICATION AND PC SOFTWARE
Communication description RS485 1 communication, RS485 2 communication
The BMS uses RS485 communication to communicate with the designated upper
computer through a special communication box. The baud rate is 19200 bps by
default. Thus, various information of the battery can be viewed at the upper
computer terminal, including battery voltage, current, temperature, status,
SOC, SOH and battery production information.
Parameter settings and corresponding control operations can be carried out to
support the program upgrade function. Support the customer protocol (This
upper computer is applicable to the PC of Windows series platform.)
DIAL SWITCH ADDRESS SETTING
When the battery pack is used in parallel, different PACKs can be distinguished by hardware address, and the hardware address of each PACK in the whole battery stack is unique. The hardware address can be set in turn through the dial switch on the board, with 1, 2, 3, 4, dials. Refer to the following table for the definition of switches.
Address | Setting &Explain |
---|---|
1 | 2 |
OOOO(O) | OFF |
“MASTER (OOOO)”, act as the host during parallel communication
OOO1(1)| ON| OFF| OFF| OFF| Select “SLAVE1 (OOO1)” for single 485
communication
OO1O(2)| OFF| OFF| ON| OFF| Select “SLAVE2(OO1O)” for single 485 communication
OO11(3)| ON| OFF| ON| ON| Select “SLAVE3(OO11)” for single 485 communication
O1OO(4)| OFF| ON| OFF| OFF| Select “SLAVE4(O1OO)” for single 485 communication
O1O1(5)| ON| ON| OFF| ON| Select “SLAVE4(O1O1)” for single 485 communication
O11O(6)| OFF| ON| ON| OFF| Select “SLAVE4(O11O)” for single 485 communication
O111(7)| ON| ON| ON| ON| Select “SLAVE4(O111)” for single 485 communication
1OOO(8)| ON| OFF| OFF| OFF| Select “SLAVE4(1OOO)” for single 485 communication
1OO1(9)| ON| OFF| OFF| ON| Select “SLAVE4(1OO1)” for single 485 communication
1O1O(1O)| ON| OFF| ON| OFF| Select “SLAVE4(1O1O)” for single 485 communication
1O11(11)| ON| OFF| ON| ON| Select “SLAVE4(1O11)” for single 485 communication
11OO(12)| ON| ON| OFF| OFF| Select “SLAVE4(11OO)” for single 485 communication
11O1(13)| ON| ON| OFF| ON| Select “SLAVE4(11O1)” for single 485 communication
111O(14)| ON| ON| ON| OFF| Select “SLAVE4(111O)” for single 485 communication
1111(15)| ON| ON| ON| ON| Select “SLAVE15(1111)” for single 485 communication
STORAGE ANDOTHERS
Long Time Storage
If stored for a long time(don’t used, exceed three months), the cell should be
stored in drying and cooling place. The PACK is to be stored in a condition
that the tempera- ture of 23±2℃ and the humidity 0f 45%- 75%. Long-term use
of unused batteries to recharge every 3 months. Ensure that the battery
voltage is within the above range。
WARRANTY
10 Year Warranty for After-Sales
The LiFePO4 batteries come with 10-year manufacturer’s defect warranty from
the date of battery purchase.
*Note: All batteries are fully tested before being shipped. Warranty is a guarantee against manufacturer defects only.
GoKWh warrants this battery to be free from manufacturer defects for 10 years.
lf for some improbable circumstance the battery is defective, we will replace
the battery. The following situation is not covered by the warranty: Batteries
that have been poorly maintained, incorrectly charged, reversed polarity,
improperly installed, stored and used in excessive heat, physical damage,
fifire, freezing, water damage, tampering, damage to terminals, failure to
maintain proper battery charge or use in excess of rated charge/discharge
cycles. Loss or damage due to force majeure or external causes, misuse,
accident, negligence, unauthorized modifification or repair.
Warranties apply only to the original owner and are not transferable. We will
verify your purchase before processing any warranty claims or returns. The
buyer intentionally conceals or fails to cooperate in providing usage
information.
GoKWh has a team of technicians to provide technical support if needed. Proof
of purchase and your usage will be requested. The customer is responsible for
shipping costs. If we deem the product manufacturer defective, we will cover
the replacement shipping costs.
Make Your Daily Power Up.
hi@gokwh.com
+86-18566184618
gokwh.com
Pugin Road, Tangxia Town, Dongguan, Guangdong, China
Dongguan GoKWh Technology Co , Ltd .
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>