Benito H6006 Control Panel User Manual

Benito H6006 Control Panel

Product Information

Specifications

• Power Supply: 230V / 50Hz (Models 230V), 120V / 60Hz (Models 120V)
• Maximum Motor Load: 700W
• Maximum Accessories Load: 3W
• Working Temperature: Not specified
• Protection: IP55
• Fuse: F1 = 5A delayed (Models 230V), F1 = 8A delayed (Models 120V)
• Dimensions: 170 x 185 x 70 mm
• Weight: 800g

Electrical Connections

• L1: Central Antenna
• L2: Antenna Shielding
• L3: START1 – Activation input 1 for traditional devices with normally open contact (opening/closing)
• L4: START2 – Activation input 2 for traditional devices with normally open contact (closing/timer)
• L5: STOP Command. Normally closed contact
• L6: Photocell. Normally closed contact
• L7: Edge. Normally closed contact or resistive edge
• L8: Common (-) commands
• L9 – L10: 24VAC power output for RX photocells and accessories
• L10 – L11: TX photocell power supply for functional test
• C1: Motor Opening
• C2: Motor Common
• C3: Motor Closing
• D1 – D2: Contact to activate the courtesy light timer
• D3 – D4: Flashing light 230V 40W / 120V 40W
• N: Power Neutral 230V / 120V
• L: Power Phase 230V / 120V
• J1: NOT USED

Product Usage Instructions

Regulation of Working Times

WARNING: The adjustment of times must be done with the roller shutter at rest.
PAUSE: Pause time before automatic reclosing.

Receiver Work and Pause Settings
Use the diagram provided to set the receiver work and pause times.

Indicator LEDs on the Unit

• START: LED on when START1 input is closed, LED off when START1 input is open
• IN2: LED on when START2 input is closed, LED off when START2 input is open
• STOP: LED on when STOP input is closed, LED off when STOP input is open
• PHOTO: LED on when PHOTO input is closed, LED off when PHOTO input is open

Frequently Asked Questions (FAQ)

• What are the maximum motor load and maximum accessories load of the unit?
  The maximum motor load is 700W, and the maximum accessories load is 3W.

• What is the working temperature range of the unit?
  The working temperature range is not specified in the manual.

• What are the dimensions and weight of the unit?
  The dimensions of the unit are 170 x 185 x 70 mm, and it weighs 800g.

IMPORTANT REMARKS

• For any installation problem please contact our Customer Service at the number +39-0172.812411 operating Monday to Friday from 8:30 to 12:30 and from 14:00 to 18:00.

• V2 has the right to modify the product without previous notice; it also declines any responsibility to damage or injury to people or things caused by improper use or wrong installation.
  Please read this instruction manual very carefully before installing and programming your control unit.

  • This instruction manual is only for qualified technicians, who specialize in installations and automations.
  • The contents of this instruction manual do not concern the end user.
  • Every programming and/or every maintenance service should be done only by qualified technicians.

• AUTOMATION MUST BE IMPLEMENTED IN COMPLIANCE WITH THE EUROPEAN REGULATIONS IN FORCE:

  • EN 60204-1 (Machinery safety. electrical equipment of machines, part 1: general rules)
  • EN 12445 (Safe use of automated locking devices, test methods)
  • EN 12453 (Safe use of automated locking devices, requirements)

• The installer must provide for a device (es. magnetotermical switch) ensuring the omnipolar sectioning of the equipment from the power supply. The standards require a separation of the contacts of at least 3 mm in each pole (EN 60335-1).

• After making connections on the terminal board, use one hose clamp to fix dangerous voltage wires near the terminal board and another hose clamp to fix safety low voltage wires used for accessories connection; this way, in case of accidental detachment of a conducting wire, dangerous voltage parts will not come into contact with safety low voltage ones.

• The plastic case has an IP55 insulation; to connect flexible or rigid pipes, use pipefittings having the same insulation level.

• Installation requires mechanical and electrical skills, therefore it shall be carried out by qualified personnel only, who can issuethe Compliance Certificate concerning the whole installation (EEC Machine Directive 89/392, Annex IIA).

• The automated vehicular gates shall comply with the following rules: EN 12453, EN 12445, EN 12978 as well as any local rule in force.

• Also the automation upstream electric system shall comply with the laws and rules in force and be carried out workmanlike.

• The door thrust force adjustment shall be measured by means of a proper tool and adjusted according to the max. limits, which EN 12453 allows.

• Connect the earthing lead of the motors to the electricity grid earth system.

• Observe all necessary precautions (e.g. anti-static bracelet) for handling parts sensitive to electrostatic discharges.

EU DECLARATION OF CONFORMITY

• The manufacturer V2 S.p.A., headquarters in Corso Principi di Piemonte 65, 12035, Racconigi (CN), Italy
• Under its sole responsibility hereby declares that the products: EASY2 comply with the following directives:
  • 2014/30/EU (EMC Directive )
  • 2014/35/EU (Low Voltage Directive)
  • ROHS-3 2015/863/EU

DISPOSAL

• As for the installation operations, even at the end of this product’s life span, the dismantling operations must be carried out by qualified experts.
• This product is made up of various types of materials: some can be recycled while others need to be disposed of.
• Find out about the recycling or disposal systems envisaged by your local regulations for this product category.
• Important! – Parts of the product could contain pollutants or hazardous substances which, if released into the environment, could cause harmful effects to the environment itself as well as to human health.
• As indicated by the symbol opposite, throwing away this product as domestic waste is strictly forbidden. So dispose of it as differentiated waste, in accordance with your local regulations, or return the product to the retailer when you purchase a new equivalent product.
• Important! – the local applicable regulations may envisage heavy sanctions in the event of illegal disposal of this product.

DESCRIPTION OF THE CONTROL UNIT

• 230V – 50Hz or 120V – 60Hz power supplies, depending on the model, for 1 x 700 W max. single phase motor.
• 2 inputs for key selector switch or button activation.
• Input for safety photocell.
• Input for safety edge, capable of handling standard edges with switch normally closed, optical edges and conductive rubber edges with nominal resistance of 8.2 kOhms.
• Output for blinking light, 120/230V – 40W
• Pre-opening safety device testing.
• Dip-switch programmable operational logic.
• Adjustment of the operation time by means of a trimmer.
• Quick plug-in connector for inserting a MR series receiver.
• LED monitoring of inputs.
• Courtesy light output.
• IP55 casing.

TECHNICAL SPECIFICATIONS

ELECTRICAL CONNECTION TABLE

ADJUSTMENT OF OPERATING TIMES

The operating times can be adjusted using two trimmers on the controller:

• WORK: Operating time for the motor (2 to 120 seconds)
  WARNING: The times must be adjusted with the shutter in standby

• PAUSE: Pause time that precedes automatic closure (2 to 180 seconds)

PLEASE NOTE : If not used, the normally closed inputs (STOP, PHOTO, EDGE) must be jumpered with the commands common line COM (-). Disable the functional test for photocells and safety devices (Dip 9 and 12 in the OFF position)

CONTROL UNIT INDICATORS (LEDS)

The highlighted boxes indicate the state of the LEDs when the roller shutter is resting.

CABLE GLAND ASSEMBLY

The casing can accept 4 cable glands in the special easy-break housings. The type of cable gland is indicated in the figure.
PLEASE NOTE:

• Remove the electronic circuit board before drill the casing.
• Drill the container using a suitably sized cutter, according to the dimensions of the cable gland.
• Fix the cable glands using the special nuts

INSTALLATION

Installation of the control unit, the safety devices and accessories must be performed with the power supply disconnected.

POWER SUPPLY

• The control unit must be powered by means of a 230 V – 50 Hz or 120 V – 60 Hz power line, depending on the model, protected by a differential magnetothermal switch in compliance with legal regulations.
• Connect the power cables to the control unit L and N terminals.

MOTOR

• The controller can drive an alternating current asynchronous motor equipped with limit switch.
• Connect the cables for motor as follows:
  • Opening cable to terminal C1
  • Closing cable to terminal C3
  • Common return cable to terminal C2

BLINKER

The control unit provides for the use of a 230 V – 40 W or 120 V – 40 W blinker with built-in intermittence. Connect the cables to terminals D3 and D4

COURTESY LIGHT

• This output has a normally-open clean contact relay which closes for approx. 1 second at the start of an opening phase. This switch may be used to activate a courtesy light timer (max. load: 230V – 4A).
  PLEASE NOTE: If there is no timer, the courtesy light can be controlled using channel 4 of receiver MR: bistable or timer programmable channel (read the instructions for the receiver MR thoroughly).

• The switch is on terminals D1 and D2

PHOTOCELLS

• The control unit has a 24VAC power supply for photocells with
  switch normally closed, and can perform an operational test
  before starting the roller shutter opening procedure.

• The photocell can be used with two settings:

Photocell always active:

• Intervention of the photocell during opening or closing causes the roller shutter to stop.
• When the photocell restores, the roller shutter re-opens completely.

Photocell NOT active during opening:

• Intervention of the photocell during opening is ignored. Intervention of the photocell during closing causes the gate to re-open completely.
• Independently of the setting selected, when the gate is paused while opening, the time count for any automatic re-closure will only start after the photocell restores.
  • Connect the photocell transmitter power cables between terminals L10 (GND) and L11 (+) on the control unit.
  • Connect the photocell receiver power cables between terminals L10 (GND) and L9 (+) on the control unit.
  • Connect the photocell receiver output between terminals L6 and L8 on the control unit.

SAFETY EDGES

The control unit has an input for controlling safety edges; this input is capable of controlling standard edges with switch normally closed and conductive rubber edges with nominal resistance of 8.2 kOhms.
Edges can be used with two settings:

1. Edge always active:
   Intervention of the photocell during opening or closing causes the roller shutter to stop.

2. Edge NOT active during opening:
   Intervention of the edge during opening is ignored. Intervention of the edge during closing causes the roller shutter re-open completely.

   • NOTE: Independently of the settings selected, any subsequent automatic re-closure will be cancelled.
   • Standard edge with switch normally closed: connect the edge cables between terminals L7 and L8 on the control unit. In order to satisfy the requirements of standard EN12978, it is necessary to install safety edges with a control unit which constantly monitors correct operation. If control units are used with the option of running tests by means of interrupting the power supply, connect the control unit power supply cables between terminals L10 (GND) and L11 (+).
   • Conductive rubber edge: connect the edge cables between terminals L7 and L8 on the control unit.
   • PLEASE NOTE: operational testing on edges is reserved for optical edges and standard edges (only if equipped with suitable control units).
   • DO NOT enable testing if conductive rubber edges are used or standard edges used without a suitable control unit for controlling function.
   • NOTE: use the special interface (code 35A024) for connection of the optical bars, de-activating the operational test on the bars

START INPUTS

The START1 and START2 inputs are factory set for connection to devices with normally open (NO) contacts. Their operation depends on the operating mode set on dipswitches 1, 2, 3, 4, 5, and 6.

DEAD MAN function (Dip 1 ON)
The user opens (START1) and closes (START2) maintaining this command active.
WARNING: The settings of Dips 2, 4, 5, and 6 are ignored

WARNING: with the DEAD MAN function on, the intervention of the photocell or of the safety edge during the closure phase always makes the rolling shutter to stop.

CLOCK Function (Dip 2 ON)
WARNING: Set Dip 1 to OFF

• START1 Input: Normal impulse input, able to manage opening and closing, even if the CLOCK function is active.
• START2 Input: Timer input. When the START2 input is activated, the shutter opens and closes automatically only after the input is deactivated.
  If automatic closure is activated (Dip 4 ON), when the timer is deactivated the shutter does not close immediately; it closes after the set pause time.

Standard Function (Dip 1 OFF / DIP 2 OFF)
The following options are available:

• Up-Down Operation (Dip 3 ON)

  • START1 controls opening (open-stop-open-stop)
  • START2 controls closure (close–stop-close-stop)

• Start-Stop Operation (Dip 3 OFF)

  • START1 controls opening and closure (open-stop-close-stop)
  • START2 is disabled

• Automatic Closure (Dip 4 ON)
  Enable closing at the end of the pause time

• Condominium Operation (Dip 5 ON)
  Open commands are ignored if the shutter is already opening

• Inversion mode (Dip 6 ON)

  • If Start-Stop operation is enabled, START1 changes the direction of the motion during opening and closing instead of stopping the shutter.

  * Connect the wires of the device that controls the START1 input between terminals L3 and L8 on the controller.
  * Connect the wires of the device that controls the START2 input between terminals L4 and L8 on the controller

STOP

• The STOP input is intended for devices with the switch normally closed. The STOP command causes the immediate stop of the roller shutter.
• If the STOP command is given during opening or pause, then there will be no subsequent automatic re-closure.
• Connect the stop input control device cables between terminals L5 and L8 on the control unit.

PLUG-IN RECEIVER

• The control unit is suitable for plugging-in an MR series receiver with high sensitivity super-heterodyne architecture.
  PLEASE NOTE : Disconnect the power to the control
  unit before performing the following operations. Pay the utmost attention to the direction of insertion of plug-in modules.

• The MR receiver module has 4 channels, each with an associated command on the control unit:

  • CHANNEL 1 g START 1
  • CHANNEL 2 g START 2
  • CHANNEL 3 g STOP
  • CHANNEL 4 g COURTESY LIGHTS

• The functional logic for channels 1 and 2 is the same as that set for the START1 and START2 inputs on the terminal board.
  PLEASE NOTE : Read the instructions supplied with the MR receiver thoroughly for details on programming the 4 channels and the operational logic.

EXTERNAL ANTENNA

• It is recommended the external antenna be used in order to guarantee maximum radio capacity.
• Connect the antenna hot pole to terminal L1 of the control unit and the braiding to terminal L2.

FAULT MESSAGES

• At the start of each operating cycle, the controller performs an operational test of the motor drive circuit (Triac).
• Furthermore, if enabled by the relative dipswitch, it also performs a test of the photocell and safety device inputs.
• If a fault occurs, the cycle does not start.
• The messages are indicated by the warning light:
  • Blinks about 4 seconds: Triac fault (or motor disconnected)
  • Blinks about 8 seconds: Photocell or safety device fault

PROGRAMMING THE OPERATIONAL LOGIC

• It is possible for the control unit to use several different operational logic states, by simply moving the dip-switches located on the card.
• The functions associated with each individual dip-switch are listed below.

ABOUT COMPANY

• +39 0172 812411
• Technical support
  Monday/Friday 8.30-12.30 ; 14-18 (UTC+01:00 time)

Installer details

Manufacturer’s details

• V2 S.p.A.
• Corso Principi di Piemonte 65/67
• 12035 RACCONIGI CN (ITALY)
• Tel. +39 0172 812411 – Fax +39 0172 84050
• [email protected]
• www.v2home.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>