i-Screamkids Cubico Android on PC User Manual

USER MANUAL

Cubico Android on PC

Note: A plastic tab was attached to the toy for in-store demonstration purposes. While the tab may have already been removed, check the back of the toy to be sure. If the plastic tab is still attached, open the fasteners on the back of the toy and pull to remove the tab. Close the fasteners and throw the plastic tab away.
Name : LV1-CUBICO
Registered trade name : i-Screamkids INC.
Address of the manufacturer : 1B-604, 660, Daewang Pangyo-ro, Bundang-gu, Seongnam-si, Gyeonggi-do, Republic of Korea
Website : http://www.cubicoding.com
cubico@i-screamkids.com

AR KIDS CODING
Please keep this instruction sheet for future reference, as it contains important information.

COMPONENT

COMPATIBLE DEVICES

• Supports Android 4.4 version and above; iOS 11.0 version and above
• Android tablets & phones
• iOS tablets & phones
• 1GB RAM and above
• Requires rear camera & Bluetooth 4.0(BLE)
• Bluetooth connection can be incompatible depending on the devices

DOWNLOAD CUBICO APPS

• Visit our website http://www.cubicoding.com and download the CUBICO app to your device

SPECIFICATION

BATTERY INSTALLATION

1. Use the phillips screwdriver to open the battery cover on the back of the coding tray.
2. Place the two AAA batteries (not included) in the correct orientation.
3. Close the battery cover with a Phillips screwdriver.

HOW TO OPERATE THE CODING TRAY

1. Put the batteries in the coding tray and turn the power switch to the ON position.
2. The LED on the front of the tray will blink when the power is turned on.
3. When you are not using CUBICO, you can save the battery by turning off the power switch.

CONNECTING CODING TRAY

1. Enable Bluetooth on the device that has installed the CUBICO app.

2. Make sure that the LED on the front of the coding tray is blinking.

3. When you run CUBICO app, the coding tray and the device are connected automatically.

4. When the coding tray is connected to the device, the LED on the front will stay on without blinking.

5. If the above screen appears, the coding tray and the device are not connected.

6. The coding tray will automatically reconnect if it is restarted.

7. If the coding tray is not automatically connected after restarting, check if Bluetooth is enabled on the device.

HOW TO PLAY CUBICO

1. Press the CUBICO AR button to activate the AR camera
2. You can enter the stage with the hint video clip by scanning the cover of a stage board with the AR camera
3. Spread out the stage board and precode using the CUBICO arker and the Paper Coding Chips
4. Place the real Coding Blocks in the Coding Tray as you precoded to program the characters’ movements
5. The character will move as you coded if you touch the play button
6. You can customize your character by pressing the CUBICO PLAY button and scanning the character chip. Try playing the game with your own character
7. After completing all the stages, you can manipulate the various machines through the Inventor games
8. Press the SING SING CODING SONG button to learn the basic concepts of coding through exciting music video clips

Product Information Guide

WARNING:
CHOKING HAZARD -Small parts. Not for children under 3 yrs.

CAUTION

• This product and its accessories are not suitable for children under the age of 36 months, because of small parts that can be swallowed.
• Intended for children age 6 and older.
• Adult supervision recommended.
• Do not drop or give impact to the product and its accessories.
• Never attempt to disassemble or modify the product or its accessories.
• Any changes or modifications in construction of this device which are not expressly approved by the party responsible for complianccould void the user’s authority to operate the equipment.
• Use extra caution when playing near water or ice.

Battery Warning

• Batteries not included.
• Do not use rechargeable batteries.
• Do not charge non-rechargeable batteries.
• Only for electric toys using rechargeable batteries.
• Inserted with the correct polarity (+ and – )
• Remove batteries during long periods of non-use. Always remove exhausted batteries from the product.
• Never short-circuit the battery terminals.
• Dispose of batteries properly.
• Do not dispose of batteries in fire.
• Use only batteries of the type recommended.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
• Do not mix old and new batteries.
• Remove batteries from coding tray if coding tray will not be used for a long period of time.

CE Warning

• Changes and modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• It is desirable that it be installed and operated with at least 20cm or more between the radiator and person’s body (excluding extremities hand, wrists, feet, and ankles)

Disposal of Old Electrical & Electronic Equipment
(Applicable in the European Union and other European countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

FCC Compliance Statement :
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment complies with FCC RF exposure compliance requirements, a separation distance of at least 5 mm must be maintained between the antenna of this device and all persons.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio, TV technical for help
• Only shielded interface cable should be used.

Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void the users authority to operate such equipment.
App Store is a service mark of Apple Inc.
Google Play™ is a trademark of Google Inc.

MODEL: LV1-CUBICO
FCC ID : 2BD9R-CUBICO
MSIP-CRM-SI6-LV1-CUBICO
CB063H074-7001r
App Store is a service mark of Apple Inc.
Google Play™ is a trademark of Google Inc.

References

• 큐비코

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>