SOUVENIR Audio Mixer 4 Channel Sound Board Mixing Console Owner’s Manual

SOUVENIR Audio Mixer 4 Channel Sound Board Mixing Console Owner’s Manual

1.Welcome

Thank you for purchasing the F-4A audio mixer.
Please read this manual carefully for proper use of your F-4A audio mixer, Should you need technical assistance please email our thechnical help at “all- after-sales@outlook.com”.

2.Main Features

• 2 XLR Mic Linel Input + 1 pair RCA L/R Line Input and 1 pair 6.35mm L/R Line Input
• Connection PC for Recording and Playing Audio
• Bluetooth/USB playbackBuilt-in 48V phantom power supply
• Gain and treble and bass adjustment, Delay or reverb effects adjustment.

3.Included Accessories

4.Panel introduction

[MIC/LINE] Mono input jack (only available for XLR input channels 1-2) Used to connect microphones, musical instruments, or audio equipment (CD players, etc.) to this device. These jacks support both XLR and phone plugs 2 [PAD +48V] Switch (only available for XLR input Channels 1-2)
When the switch is turned on, the LED lights up to indicate that the device has applied DC+48V phantom
power to the XLR plug on the [MIC/LINE] mono input port 1-2. When using a condenser microphone powered by phantom power, turn on this switch.
NOTE: If you do not need phantom power supply, be sure to set this switch to off When operating this switch, please observe the following important precautions in order to prevent noise and damage to the unit and external equipment. “When the microphone or other equipment connected on channels 1-2 doss not support the phantom power supply function, make sure that the switch is kept off.
‘When the switch is on, do not connect/disconnect the cables on channels 1-2. Before operating this switch, set the [LEVEL] knobs of channels 1-2 to minimum. 3 [GAIN] knob
XLR input channels 1-2: Determines the basic volume of each channel from channels 1 to 2. Adjust
these controllers to make the corresponding [PEAK] LED flash briefly when singing and playing at the maximum volume.
Channels 3-4 /Bluetooth/USB input: The gain knob of the channel 3-4 /Bluetooth/USB module are
shared, unlike the 1-2 channels which has independent volume control. 4 Equalizer (EQ) knob XLR input channels 1-2: Use the [HIGH] (high band) and [LOW] (low band) knobs to adjust the sound quality
If you do not need to adjust the sound quality, you can set the knob to the “12 o’clock direction”
Channels3~4/Bluetooth/USB input : The EQ knob of the channels 3-4 /Bluetooth/USB module are shared, unlike the 1-2 channel which has independent EQ knob control. 5 [EFF] Effect switch (only available for XLR input channels 1-2)
The EFF control adjusts the effect volume of the only for channels 1-2. Channels 3-4/Bluetooth/USB modules
have no reverberation effect. 6 [PEAK] LED
It will light up when the volume of the input signal or the volume after the equalizer is too high (when it reaches 3dB below the clipping distortion). If it lights up frequently, turn the [GAIN] knob to the left to decrease the
volume. 7 [LEVEL] knob Used to adjust the volume balance between each channel. Usually this switch is set to the “3 o’clock direction” position. 8 [ST/ USB] switch
This switch key is to switch between computer recording playback or Bluetooth/USB module. When you use computer recording input, remember to note that this key is not pressed. When you use a BluetoothVUSB module, this button is pressed.
NOTE: Bluetooth and USB functions are only available as one of the two options and cannot be used simultaneously.
RCA L/R Line Output jack 1 Pair
Used for output connections, devices that support RCA jacks.
RCAL/R Line Input jack 1 Pair For input connections, devices that support lotus line jacks.For example, CD player, mobile, compuer, electronic organ ect.
6.35mm L/R Line Input jacks 1 Pair Itis used for input connection and supports 6.35mm-line jack devices. For example, CD player, mobile, computer,electronic organ ect.
6.35mm L/R Line Output jacks 1 Pair Itis used for output connection and supports 6.35 line socket equipment. For example, active speaker, power amplifier ect 13 USB input
Used for USB port device input. Such PC, USB Stick, MP3 devices ect, it can be used for music playback and recording to USB stick output. 14 Display Used to display USB mode or Bluetooth mode.
MP3 player controller The first right button: playback pause; the second right button: next song; the left button: switch the sound source mode; the right button: previous song.
[DELAY] Delay effect knob (only available for XLR input Channels 1-2) Adjust the intensity of the delay effect processing for the input signal
Power switch LED
[PHONES] output jack
Used to connect headphones
[REPEAT] Reverb effect knob
reverberation effect processing for the input signal. (This feature is only available for XLR input Channels 1-2) 20 [PHONES] knob
You can adjust the volume of the sound output from the [PHONES] jack. 21 [MAIN] knob The main signal output control knob. 22 [DC5V 1A] audio mixer power port or computer connection Used to connect the included power cable, There are three ways to power up the mixer. 1. Power up with the supplied AC adapter and power cord connection. 2. It can be connected with the supplied power cord with the power bank 3: You can connect to your computer with the included power cord.
Switch knob for computer and USB Bluetooth module Used to switch computers and USB Bluetooth modules, Computer connection,Bluetooth and USB functions are only available as one of the three options and cannot be used simultaneously.

5. General Specifications

6.Compatible Devices and Connection Methods

7. How to Use the Audio Mixer?

Step 1

1.1: Connect the type-c power cable to mixer,then connect the Supplied AC adapter.
1.2: Adjust all level control knobs to zero. Includes [Gain] knob (red), [Level] knob (blue) and [Main] knob (white); Then set the equalizer knob (green) to the center “12 o’clock”
1.3: Tum on the power switch button.
1.4: Connect the output device (active speakers or power amplifier + passive speakers) to the output device jack of the mixer.

Step 2

2.1:If you connect a device with high output level, such as a CD player or an electrickeyboard to connect the channels 1-3, Press the [PAD] switch of the corresponding channel

2.2: Set the [LEVEL] knob as required to adjust the volume balance between the corresponding channels.
NOTICE There are three functions to adjust the volume: [PAD], [GAIN] and [LEVEL]. Once the [PAD] switch and [GAIN] knob have been set, do not adjust these
controls as much as possible. Generally, the volume is adjusted with the [LEVEL] knob.

8. Operating Steps for Computer Recording

1. First connect the pc or laptop to the mixer using a cable to power it on and then directly openthe recording software to record(no need to install a driver)
2. Before connecting to the computer to record,you need to set the computer as follows:

Windows system settings

1. Open the Start menu, and then click Control Panel.
2.  Open the sound preferences from the control panel folder.
3. Click “Record” and set the microphone to the defauit value to start recording.

Apple system settings

How to record via USB jack

1. Plug in usb stick, flash drive.

2. Press MODE button until “ USB REC shown on the LCD and you will hear the voice prompt *
   Recording Mode” , at this time, start recording automatically to USB.

3. Press the Ml button to start or pause recording.

4. Press the MODE button to finish recording and save the file in the MP3 format&Play recording file.

10.0perating Steps for Bluetooth Playback

1. Press MODE button until “BT” shown on the LCD and you will hear the voice prompt * The bluetooth device is ready to pair” If Bluetooth is not connected, the word “BT” will keep flashing
2. Open Bluetooth mode on the phone, click “F-5A” to connect successfully,and you will hear the voice prompt “Bluetooth connect successful, and then play music
3. Press the M button to start or pause music, Press the < and MM switch songs.

‘NOTE: When using Bluetooth and USB functions. Pls press this key (am ) )
NOTE: Bluetooth and USB functions are only available as one of the two options and cannot be used simultaneously.

11.0peratin• Steps for USB Pla Music

1. Plugi n usb stick.flash drive MP3
2. Press MODE button until”MP3″shown on the LCD and you will hear the voice prompt’Music Play Mode’. Then music automatically plays
3. Press the M button to start or pause music, Press the I« and »M switch songs.

NOTE: When using Bluetooth and USB functions, Pis press this key (_am ) )
NOTE: Bluetooth and USB functions are only available as one of the two options and cannot be used simultaneously.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>