DIODES AP64500SP-EVM Low IQ Synchronous Buck With Programmable Frequency User Guide

June 16, 2024
DIODES

DIODES AP64500SP-EVM Low IQ Synchronous Buck With Programmable Frequency User Guide
DIODES AP64500SP-EVM Low IQ Synchronous Buck With Programmable
Frequency

DESCRIPTION

The AP64500 is 5A, synchronous buck converter with a wide input voltage range of 3.8V to 40V. The device fully integrates a 45mΩ high-side power MOSFET and a 20mΩ low-side power MOSFET to provide high-efficiency stepdown DC-DC conversion.

The AP64500 device is easily used by minimizing the external component count due to its adoption of peak current mode control.

The AP64500 design is optimized for Electromagnetic Interference (EMI) reduction. The device has a proprietary gate driver scheme to resist switching node ringing without sacrificing MOSFET turn-on and turn-off times, which reduces high-frequency radiated EMI noise caused by MOSFET switching. AP64500 also features Frequency Spread Spectrum (FSS) with a switching frequency jitter of ±6%, which reduces EMI by not allowing emitted energy to stay in any one frequency for a significant period of time.

The device is available in a SO-8EP package.

  • Frequency Spread Spectrum (FSS) to Reduce EMI
  • Low-Dropout (LDO) Mode
  • Precision Enable Threshold to adjust UVLO
  • Protection Circuitry
    • Undervoltage Lockout (UVLO)
    • Output Overvoltage Protection (OVP)
    • Cycle-by-Cycle Peak Current Limit
    • Thermal Shutdown
  • Totally Lead-Free & Fully RoHS Compliant
  • Halogen and Antimony Free. “Green” Device

APPLICATIONS

  • 5V, 12V, and 24V Distributed Power Bus Supplies
  • Power Tools and Laser Printers
  • White Goods and Small Home Appliances
  • Home Audio
  • Network Systems
  • Consumer Electronics
  • General Purpose Point of Load

TYPICAL APPLICATIONS CIRCUIT

Figure 1. Typical Application Circuit
TYPICAL APPLICATIONS CIRCUIT

ABSOLUTE MAXIMUM RATINGS

Symbol Parameter Rating Unit
VIN Supply Pin Voltage -0.3 to +42.0 (DC) V

-0.3 to +45.0 (400ms)
VBST| Bootstrap Pin Voltage| VSW – 0.3 to VSW + 6.0| V
VEN| Enable/UVLO Pin Voltage| -0.3 to +42.0| V
VRT/CLK| RT/CLK Pin Voltage| -0.3 to +6.0| V
VFB| Feedback Voltage| -0.3V to +6.0| V
VCOMP| Compensation Pin Voltage| -0.3 to +6.0| V
VSW| Switch Node Voltage| -0.3 to VIN + 0.3 (DC)| V
-2.5 to VIN + 2.0 (20ns)
TJ| Junction Temperature| +160| °C
TL| Lead Temperature| +260| °C

RECOMMENDED OPERATING CONDITIONS

Symbol Parameter Min Max Unit
VIN Supply Voltage 3.8 40 V
VOUT Output Voltage 0.8 39 V
TA Operating Ambient Temperature Range -40 +85 °C
TJ Operating Junction Temperature Range -40 +125 °C

EVALUATION BOARD

Figure 2. AP64500SP-EVM
EVALUATION BOARD

QUICK START GUIDE

The AP64500SP-EVM has a simple layout and allows access to the appropriate signals through test points. To evaluate the performance of the AP64500SP, follow the procedure below:

  1. Connect a power supply to the input terminals VIN and GND. Set VIN to 12V.
  2. Connect the positive terminal of the electronic load to VOUT and negative terminal to GND.
  3. For Enable, to enable IC, place a jumper at JH6 to “ON” position to connect EN pin to VIN through 100KΩ resistor or leave it OPEN. Jump to “OFF” position to disable IC.
  4. The evaluation board should now power up with a 5.0V output voltage.
  5. Check for the proper output voltage of 5.0V (±1%) at the output terminals VOUT and GND. Measurement can also be done with a multimeter with the positive and negative leads between VOUT and GND.
  6. Set the load to 5A through the electronic load. Check for the stable operation of the SW signal on the oscilloscope. Measure the switching frequency.

MEASUREMENT/PERFORMANCE GUIDELINES:

  1. When measuring the output voltage ripple, maintain the shortest possible ground lengths on the oscilloscope probe. Long ground leads can erroneously inject high frequency noise into the measured ripple.
  2. For efficiency measurements, connect an ammeter in series with the input supply to measure the input current. Connect an electronic load to the output for output current

SETTING OUTPUT VOLTAGE:

Table 1 shows a list of recommended component selections for common output voltages.

Table 1. Common Output Voltages

VOUT| R1| R2| L1| R7| C7| C1, C2| C5, C6, C13
---|---|---|---|---|---|---|---
1.2V| 4.99KΩ| 10KΩ| 1.5µH| 3.74KΩ| 2.7nF| 2×10µF| 3×22µF
1.5V| 8.66KΩ| 10KΩ| 2.2µH| 4.75KΩ| 2.7nF| 2×10µF| 3×22µF
1.8V| 12.4KΩ| 10KΩ| 2.2µH| 5.62KΩ| 2.7nF| 2×10µF| 3×22µF
2.5V| 21.5KΩ| 10KΩ| 3.3µH| 7.87KΩ| 2.7nF| 2×10µF| 3×22µF
3.3V| 31.6KΩ| 10KΩ| 3.3µH| 10.5KΩ| 2.7nF| 2×10µF| 3×22µF
5.0V| 52.3KΩ| 10KΩ| 3.6µH| 15.8KΩ| 2.7nF| 2×10µF| 3×22µF
12V| 140KΩ| 10KΩ| 10µH| 37.4KΩ| 2.7nF| 2×10µF| 3×22µF

EVALUATION BOARD SCHEMATIC

Figure 3. AP64500SP-EVM Schematic
EVALUATION BOARD SCHEMATIC

PCB TOP LAYOUT

Figure 4. AP64500SP-EVM – Top Layer
PCB TOP LAYOUT

PCB BOTTOM LAYOUT

Figure 5. AP64500SP-EVM – Bottom Layer
PCB BOTTOM LAYOUT

BILL OF MATERIALS for AP64500SP-EVM for VOUT=5V

**Ref| ****Value| ****Description| ****Qty| ****Size| ****Vendor Name| ****Manufacturer PN| PCB Layer
---|---|---|---|---|---|---|---
**
C1, C2| 10µF| Ceramic Capacitor,50V, X7R, 10%| 2| 1206| Samsung| CL31B106KBHNNNE| Top
C3, C4,C9| 0.1µF| Ceramic Capacitor,50V, X7R, 10%| 2| 0603| WurthElectronics| 885012206095| Top
C5, C6,C13|
22µF| Ceramic Capacitor,16V, X7R| 3| 1210| Samsung| CL32B226KOJNNNE| Top
C7| 2.7nF| Ceramic Capacitor, 50V, X7R| 1| 0603| Murata| GRM1885C1H272JA01D| Top
R1| 52.3KΩ| SMD Resistor, 1%| 1| 0603| Panasonic| ERJ-3EKF5232V| Top
R2| 10KΩ| SMD Resistor, 1%| 1| 0603| Panasonic| ERJ-3EKF1002V| Top
**** R3| **** 0Ω| RES SMD 1% 1/10W| **** 1| **** 0603| **** Vishay| **** CRCW06030000Z0EAC| **** Top
**** R4| **** 100KΩ| RES SMD 1% 1/10W| **** 1| **** 0603| **** Vishay| **** CRCW0603100KFKEA| **** Top
R6| 200KΩ| RES SMD 1% 1/10W| 1| 0603| Yageo| RC0603FR-07200KL| Top
R7| 15.8KΩ| RES SMD 1% 1/10W| 1| 0603| Bourns Inc| CR0603-FX-1582ELF| Top
L1| 3.6µH| DCR=12.2mΩ, Ir=8.2A| 1| 10.2×10.2×4.5mm| Wurth Electronics| 7447797360| Top
JH6| | PCB Header, 40POS| 1| 1X3| 3M| 2340-6111TG| Top
VIN,VOUT, GNDx2|
1598| Terminal TurretTriple 0.094″ L (Test Points)| 4| Through- Hole| Keystone Electronics| 1598-2| Top
U1| AP64500| Sync DC-DC Converter| 1| SO-8EP| Diodes Incorporated (Diodes)| AP64500SP| Top

TYPICAL PERFORMANCE CHARACTERISTICS

Figure 6. Efficiency vs. Output Current
TYPICAL PERFORMANCE

Figure 7. Load Transient 3A to 5A
TYPICAL PERFORMANCE

Figure 8. Output Voltage Ripple, IOUT=5A
TYPICAL PERFORMANCE

Figure 9. Output Short Protection, IOUT=5A
TYPICAL PERFORMANCE

IMPORTANT NOTICE

  1. DIODES INCORPORATED (Diodes) AND ITS SUBSIDIARIES MAKE NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO ANY INFORMATION CONTAINED IN THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION).
  2. The Information contained herein is for informational purpose only and is provided only to illustrate the operation of Diodes’ products described herein and application examples. Diodes does not assume any liability arising out of the application or use of this document or any product described herein. This document is intended for skilled and technically trained engineering customers and users who design with Diodes’ products. Diodes’ products may be used to facilitate safety-related applications; however, in all instances customers and users are responsible for (a) selecting the appropriate Diodes products for their applications, (b) evaluating the suitability of Diodes’ products for their intended applications, (c) ensuring their applications, which incorporate Diodes’ products, comply the applicable legal and regulatory requirements as well as safety and functional-safety related standards, and (d) ensuring they design with appropriate safeguards (including testing, validation, quality control techniques, redundancy, malfunction prevention, and appropriate treatment for aging degradation) to minimize the risks associated with their applications.
  3. Diodes assumes no liability for any application-related information, support, assistance or feedback that may be provided by Diodes from time to time. Any customer or user of this document or products described herein will assume all risks and liabilities associated with such use, and will hold Diodes and all companies whose products are represented herein or on Diodes’ websites, harmless against all damages and liabilities.
  4. Products described herein may be covered by one or more United States, international or foreign patents and pending patent applications. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks and trademark applications. Diodes does not convey any license under any of its intellectual property rights or the rights of any third parties (including third parties whose products and services may be described in this document or on Diodes’ website) under this document.
  5. Diodes’ products are provided subject to Diodes’ Standard Terms and Conditions of Sale (https://www.diodes.com/about/company/terms-and-conditions/terms-and-conditions-of-sales/) or other applicable terms. This document does not alter or expand the applicable warranties provided by Diodes. Diodes does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel.
  6. Diodes’ products and technology may not be used for or incorporated into any products or systems whose manufacture, use or sale is prohibited under any applicable laws and regulations. Should customers or users use Diodes’ products in contravention of any applicable laws or regulations, or for any unintended or unauthorized application, customers and users will (a) be solely responsible for any damages, losses or penalties arising in connection therewith or as a result thereof, and (b) indemnify and hold Diodes and its representatives and agents harmless against any and all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim relating to any noncompliance with the applicable laws and regulations, as well as anyunintended or unauthorized application.
  7. While efforts have been made to ensure the information contained in this document is accurate, complete and current, it may contain technical inaccuracies, omissions and typographical errors. Diodes does not warrant that information contained in this document is error-free and Diodes is under no obligation to update or otherwise correct this information. Notwithstanding the foregoing, Diodes reserves the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes.
  8. Any unauthorized copying, modification, distribution, transmission, display or other use of this document (or any portion hereof) is prohibited. Diodes assumes no responsibility for any losses incurred by the customers or users or any third parties arising from any such unauthorized use.
  9. This Notice may be periodically updated with the most recent version available at https://www.diodes.com/about/company/terms-andconditions/important-notice

The Diodes logo is a registered trademark of Diodes Incorporated in the United States and other countries.
All other trademarks are the property of their respective owners.
© 2024 Diodes Incorporated. All Rights Reserved.

DIODES Logo

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals