Ninghui TLG85B GPS Speedometer with Fuel Gauge Voltmeter User Guide
- June 16, 2024
- Ninghui
Table of Contents
User Guide for 85mm GPS Speedometer with Fuel Gauge Voltmeter
TLG85B GPS Speedometer with Fuel Gauge Voltmeter
- GND
- Power +(12/24V)
- Fuel Level Alarm(+)
- Low Battery Volt Charging Alarm(+)
- Water Temp Alarm(+)
- Oil Pressure Alarm(+)
- External Button (+)
- Fuel Gauge Signal
Install the Gauge
a. Cut an 85mm (3 3/8″) hole in the panel (II) allow a clearance of . behind
the panel.
b. Remove fastening ring (I), insert gauge from front. Tighten gauge (III)
using fastening ring ( I)
c. Securely fasten the GPS antenna, preferably outdoors (or inside front
windscreen) so that it has a clear view of the sky to pick up satellite
signals. Connect the antenna cable to socket on the gauge. Do not cut cable.
d. After turning power on, allow the gauge to sample satellite signal for 1
minute.
e. All data is for reference only and should not be trusted as sole navigation
source.
Parameter Menu:“BUZZ” , “ODO”, “UNIT”, “OIL”,“PULSE”
Press and Hold the back button, then power on. The LCD will switch show BUZZ,
ODO, UNIT,OIL, PULSE.
-
“ BUZZ”(Set Overspeed Buzzer Alarm Speed Threshold)LCD will show“B 80”(Buzzer will alarm when speed more than 80km/h), press button to set from 10~240, then release button, and wait for menu to complete flashing.
-
“ ODO” (Set Total Odometer)LCD will show eg.“ 5000”(5000 km), press button to set from 0~ 999999, then release button, and wait for menu to complete flashing
-
“ UNIT” (Set Unit between km/h, mph, knots)
LCD will switch show km / h, mph, knots。then release button, and wait for menu to complete flashing . -
“OIL”(set Fuel Gauge Ohm Input Signal)
LCD will show eg. “o00002”(indicates ohm signal input range 10~180Ω).Press button to set target input signal range depends on Table A as below.
Table A
o 00000 | 0-190Ω |
---|---|
o 00001 | 0-180Ω |
o 00002 | 10-180Ω |
o 00003 | 240-33Ω |
o 00004 | 240-30Ω |
-
Switch show Fuel Gauge and Voltmeter
Press and Hold on back button 2~3 seconds, to switch show Fuel Gauge in % or Voltage in volts. -
Switch Odometer & Trip Odometer
The LCD will show Total Odometer as default. Quick press the button to switch show Trip Odometer. Long Press to reset the Trip Odometer to Zero.
Please noted: After setting, you should disconnect both Power+ and GND, and then reconnect the two cable, then it will save the setting. If you just cut Power +, then it’ll not work properly.
FCC Warnning:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection againstharmful interference in a
residential installation. This equipment generates, uses and can radiateradio
frequency energy and, if not installed and used in accordance with the
instructions, maycause harmful interference to radio communications. However,
there is no guarantee thatinterference will not occur in a particular
installation. If this equipment does cause harmfulinterference to radio or
television reception, which can be determined by turning the equipmentoff and
on, the user is encouraged to try to correct the interference by one or more
of thefollowing measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1)This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>