Kjell Company 49101 Weather Station With 3 Sensors User Manual

June 13, 2024
Kjell Company

Kjell Company 49101 Weather Station With 3 Sensors User Manual
Kjell Company 49101 Weather Station With 3 Sensors

Specifications

Temperature range indoors: 0-50 °C
Temperature range outdoors: -40-60 °C
Temperature, resolution:   0.1 °C
Humidity range:   20-95%
Humidity resolution:   1%
Batteries: 3x AAA and 6x AAA (none included)
Frequency range: 433.92 MHz
Effective radiated rower: – 14.44 dBm

Installation

Plug the power adapter into the main unit or insert 3x AAA batteries. Continue with inserting 2x AAA in each of the three sensors. Mind the polarity shown in the battery compartments.

Backlight
The main unit has a backlight feature. When the main unit is powered by the power adapter, the backlight is constantly on. If it is powered by batteries, the backlight turns on for a few seconds after pressing the Light button. Press the SNZ button to change the brightness of the display. When the weather station is receiving a RCC signal, the display is dark. If the unit has recieved the signal successfully, or the RCC signal is not received automatically after 7 minutes, the display lights up again.

Connecting the units
Place all units next to each other. The main unit will automatically detect the signals from the sensors usually wihin 3 minutes. If the main unit does not detect the signals, press the CH button on the back of the unit. The switches inside the sensors battery compartments decide which channel they are
using.

Placement of sensors and main unit
Use the mounting hole to hang the units on a nail or a screw. Place the sensors where you want to measure temperature and place the main unit indoors where you want to read the data and measure temperature and humidity. Make sure the sensors are protected from rain.

Time settings
The main unit automatically searches for a radio signal the first time it is used to set the time, this process takes 3 to 8 minutes. Press and hold the down button for 2 seconds to start a new search. If no reception can be found to set the time you will need to set the time manually. Press and hold the SET button for three seconds to open the time settings. The current value flashes. Enter the correct value with the up and down buttons. Press once to advance one step or hold the button to browse faster. Press the SET button again to confirm and repeat the same procedure until all time settings are done. Switch between the following settings:

Time zone -> Hour -> Minute -> Year -> Month -> Day -> 12/24 H -> Finish Alarm settings

Alarm settings

Press the SET button once to see the alarm display. Press and hold SET for three seconds to be able to set the alarm time. Use the arrow buttons and confirm each value with SET. Press the up/down button to enable or disable the alarm.
Press the SNZ button when the alarm goes off to activate the snooze function for 5 minutes. Stop the alarm by pressing any other button.

Weather forecast

The station shows a forecast for the upcoming 12 hours using five images. It changes between sunny, partly cloudy, cloudy, rainy and snowy. The forecast will be more accurate if the station is not placed in a room with an air conditioner.

Temperature unit

Press the up button while you are in the main view to choose between °C or °F

Specifications for power supply

Input voltage (V): AC 100 – 240 V
Input AC frequency (Hz): 50/60 Hz
Output voltage (V): DC 4.5 V
Output current (A); 0.6 A
Output power (W): 2.7 W
Average active efficiency (%): 73.64%
No-load power consumption (W): 0.073 W

Simplified EU Declaration of Conformity

Kjell & Company hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Full text of the EU declaration of conformity is available at www.kjell.com/49101

www.rubicson.com
Box 50435 Malmo
Sweden
2022-01-27

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals