YOPSTAR KS.FF.A6.024W.FC.001 Multifunctional Smart Floor Lamp User Manual

YOPSTAR KS.FF.A6.024W.FC.001 Multifunctional Smart Floor Lamp

Multifunctional Smart Floor Lamp

• (2.4G five channels+Tuya APP+2 keys) The three switch modes do not interfere with each other.
• Remote control and APP control, with dimming, color temperature adjustable and RGB color changing mode, including 5 kinds of RGBCW lighting modes.

Overview

KS A6 series LED floor lamp adopts 6063 aluminum sheet to dissipate heat, which can effectively solve the problem of LED heat dissipation. High light efficiency, low light decay, low energy consumption, no stroboscopic, no radiation, stable performance, long lifetime and other characteristics, provide a 2-year warranty.

LED Light Source

High Quality SMD2835 /SMD5050 LED

Lamp Body Shell

• Black painted shell;
• The top of the iron pipe adopts a 320° rotating universal head, and the openings on both sides can be turned back and forth;
• The switch has up and down buttons, and the switch is fixed by means of structural buckles;
• The middle iron pipe adopts a full-thread hollow thread head, and there is no obvious step or layering between the pipes.

Organic Light Guide PC

• Milky white PC cover with a thickness of 6mm, effectively shaping the light;
• The luminous cover is made of plastic PC94-2 material;
• The upper and lower iron pipes at the switch position use plastic wire fixers for anti-pull treatment.

Diversified Control Methods

1. 2.4G remote control sensing distance is greater than 20 meters;
2. The mobile phone APP Bluetooth sensing distance is greater than 10 meters;
3. The mobile phone APP Wifi sensing distance is greater than 20 meters;
4. When the light is turned on with the mechanical key, it can be turned off with the remote control or APP. After 5 seconds of turning off, the effect of the last light will be remembered;
5. No flickering, smooth and no jumping when dimming or color temperature.

Parameter

The tolerance range of test data above is ±6%， but normally warm white is ±8%.

14-Key 2.4G Remote Control

1. CCT switch key
2. Brightness+
3. Color temperature –
4. Short press RGB monochrome switch
5. Color temperature 2700K
6. Delay off key, after pressing this key, the light flashes once, and turns off the light after 30 seconds
7. RGB switch key
8. Favorite function key, single press to favorite the current lighting state
9. Color temperature+
10. RGB jump mode and gradient mode selection
11. Brightness-
12. Color temperature 6500K
13. Color temperature 4000K
14. Night light (white + yellow lights up 5% at the same time)

Description of Button Function for Remote Control

1. Press brightness+ or brightness- key to adjust the brightness of CCT. Except that RGB gradient mode cannot adjust brightness, the brightness can be adjusted in any other mode. The brightness adjustment range is 5% – 100 (Turn on the lamp after power on,long press CCT key to match / clear the code.
   After the code is matched successfully, the lamp flashes. As the code has been matched at the factory, there is no need to match the code again).

2. Press favorite key for 1 second to save the current lighting status and memorize it. Short press the favorite key to turn on the favorite lighting status.

3. When pressing night light key on the remote control, turn on 5% of white and yellow light at the same time, and press it again to turn off the night light.

4. Press RGB key on the remote control to switch to RGB monochrome mode, each short press will switch the color, red, green, blue, yellow, green and pink.
   In this mode, press brightness+ / brightness- key to adjust the brightness. It can be adjusted in five levels.

5. When pressing AUTO key on the remote control, RGB jump function is turned on for the first time, 6 colors jump, the light is on for 1 second, and the light is off for 1 second. Press AUTO key again to enter RGB gradient mode, and the whole process of 6-color gradient takes about 10 seconds.

6. Press 30S key on the remote control, the lamp will be turned off after a delay of 30 seconds.

7. Short press 2700K key, 6500K key, and 4000K key on the remote control, the corresponding brightness states are: yellow, white, neutral white and the brightness is 100%.

8. In RGB jump or gradient mode, press CCT+ / CCT- key to adjust the speed of light change. Three levels adjustment. Among them, fast, medium and slow change times of the jump mode are respectively: on-off time is 1 second (slow) 0.6 seconds (medium) 0.3 seconds (fast). The gradual transition time is: the transition time of the whole process are respectively: 10 seconds (slow) 6 seconds ( medium) 3 seconds (fast).

Dimension(mm)

Assembly Instructions

1. Turn the iron (5) clockwise to the base (6).
2. From bottom to top, connect the poles (4, 3, 2, 1) in sequence.
3. Connect the connector (7) to the power adapter (8).
4. Insert the power adapter into the power socket to complete the installation.
5. According to personal needs, the light source can be adjusted in a variety of control methods (9).

Packing Information

Model No.| Power| Inner Box(mm)| N.W.| G.W.| Carton Size(mm)| PCS/CTN| N.W.| G.W.
---|---|---|---|---|---|---|---|---
FF.A6.24W| 24W| 410108272mm| 4.2kg| 4.5kg| 452425300mm| 4| 16.9kg| 18.7kg

Application

It is suitable for public offices, homes, office buildings, shopping malls, hotels, and so on.

Quality assurance

1. Quality assurance is based on the correct storage, transportation, installation, use and maintenance of the product.
2. Man-made damage or product failure caused by improper use is not covered by the warranty.
3. During the warranty period, the company chooses the appropriate warranty service according to the actual situation, including repairing and replacing parts or replacing new products.
4. Two-year warranty.

Safety warning

Non-professionals should not perform related operations.

1. Please check the packaging and product integrity before installation. If the product is damaged due to transportation, it is prohibited to use it.
2. Avoid objects hitting or pressing the product.
3. Handle gently during transportation and installation.
4. Do not power on the product before it is installed. Please turn off the power before cleaning.
5. Avoid cleaning the surface of the lamp with chemical and corrosive materials.
6. Do not touch when the light is on.
7. It is normal for the lamp to heat up when lit.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>