PHILTRE ACL-BD3600W R Toilet Bidet Attachment with Heated Toilet Seat User Manual

PHILTRE ACL-BD3600W R Toilet Bidet Attachment with Heated Toilet Seat

• This product was manufactured for household use only.
• Read all operating instructions before installation and use.
• Please save this operating instruction manual and place in an easily accessible location.
• External appearance and specifications are subject to change for improvement of product without notice.

Important Safeguards

READ ALL INSTRUCTIONS BEFORE USING
DANGER To reduce the risk of electrocution.

• Do not use while bathing.
• Do not place or store product where it can fall or be pulled into a tub or sink.
• Do not place in or drop into water or other liquid.
• Do not reach for a product that has fallen into water. Unplug immediately.

WARNING To reduce the risk of burns, electrocution, fire or injury to persons.

• It the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

• Connect this product to a properly grounded outlet only.

• Unplug the appliance during filling and cleaning.

• Do not touch the power plug with wet hands.

• Properly connect the power cord to the electrical outlet corresponding to the rated voltage of the unit.

• Keep the cord away from heated surfaces.

• Do not use damaged or loose power cord.

• Before removing the unit from the toilet bowl, disconnect the power plug first.

• Do not connect other electrical appliances to the same power socket connected to the unit.

• Children should be supervised to ensure that they do not play with the appliance.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

• Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water.
  Return the product to a service center for examination and repair.

• Never block the air openings of the product or place it on a soft surface, such as a bed or couch, where the air openings may be blocked.

• Keep the air openings free of lint, hair, and the like. Any other servicing should be performed by an authorized service representative.

• Close supervision is necessary when this product is used by, on, or near children or invalids.

• Do not dismantle, repair, or alter the unit.

WARNING To reduce the risk of burns, electrocution, fire or injury to persons.

• Never use while sleeping or drowsy.
• Never drop or insert any object into any opening or hose.
• Do not use outdoors. or operate where aerosol(spray) products are being used or where oxygen is being administered.
• Do not pour or spray water on to the unit.
• Do not use steam cleaner.
• Keep the unit away from fires or inflammable substance.
• Do not connect to the industrial water supplies.
• Caution against low temperature burns.
• New hose-sets supplied with the appliance are to be used and that old hose-sets should not be reused.

CAUTION To reduce the risk of injury to persons or damage to the product or the property.

• Do not place heavy objects or step on the unit.
  It may cause product damage or injury.

• When cleaning the unit, do not use any chemicals. Clean the unit with moist, well-wrung soft cloth. For excessive stains, use soft cloth moistened with mild dish-wash detergent and wipe out with dry cloth.
  It may cause product damage.

• Do not slam down the lid.
  It may cause product defect.

• Do not lean on the lid.
  It may cause product defect.

• When not in use for a long period of time, disconnect the power plug and drain the water tank.
  Tank water may be contaminated and cause skin troubles.

• Do not twist or pull the connection hoses.
  It may affect water supply or cause water leakage.

• Do not cover up the warm air outlet or insert hands or other objects.
  It may cause burn or electric shock.

• Do not operate the unit during product malfunction.
  Disconnect the power plug and call the authorized service center. It may cause fire or electric shock if the unit is operated while it is out of order.

Grounding Instructions

WARNING Improper use of the grounding plug can result in risk of electric shock.

• This product is for use a nominal 120v circuit and a GFCI (ground fault circuit interrupter) receptacle is required for use with this product. Do not use this product with an ungrounded outlet. Do not use an extension cord with this product.
• If you do not have a GFCI receptacle, contact a qualified electrician to have installed.

List of parts

Installation Method

Before Installation

• Read the instructions carefully before installing.
• Plug in only after complete installation then supply water Installation Procedure

1. Separate water supply hose
   Turn the water supply valve clockwise to lock, and separate the toilet hose using a spanner.

2. Water: Remove the existing toilet seat
   Unfasten the nut and remove the toilet seat.
   Save the old toilet lid and nuts for reinstallation later.

3. Connect T-valve
   Install T-valve as shown

4. Insert the base bracket.
   Align the base bracket groove with the toilet seat hole.
   Insert the fixing bolt into the base bracket and toilet sent hole

5. Insert the bidet body
   Mount the main bidet into the fixing holes.
   Align the front of the bidet body and the front of the toilet before fastening the nuts.

6. Connect the flexible hose
   Connect the flexible hose to the
   T-valve and the main body.
   Turn the water supply valve counterclockwise to allow water flow.

Operation check

1.  Turn the water supply valve counterclockwise to check for water leakage.
2. Connect the power plug into electrical outlet.
3.  Check the function for each type of use.

For instruction videos, please visit htts://Philtre.life/Bidet-Install- Instruction/, or scan below QR Code with your mobile device.

For one-piece toilets, use Top mounting kit (included) and visit htts://Philtre.life/Top-Mounting-Install-Instruction/, or scan below QR Code with your mobile device.

How to use

STOP
 Press Stop button when you want to stop the function.

REAR WASH

• Press REAR WASH / NOZZLE POSITION button to start wash function.
• Press the button again during using this function, Move (Oscillation )function works
• Press the Move again, then Move function stops.

FRONT WASH

• Press FRONT WASH / NOZZLE POSITION buttons to start wash function.
• Press the button again during using this function, Move Oscillating) function works.
• Press the Move again, then Move function stops.

EASY BOWEL

• Press EASY BOWEL button to start elevated-strength rear wash function
• It starts from the highest water pressure.

AIR DRY

• Use this after using wash function.
• Wipe excessive water with toilet paper before using dry function for best results.
• Air drying stops automatically in 3 minutes.

MASSAGE

• Press the MASSAGE button during FRONT/REAR WASH functions, water pressure pulsates from strong to soft.
• Press the button again, then Massage function stops.

WATER PRESSURE / DRY TEMP
5 levels of Water pressure/ Dry temperature.

NOZZLE POSITION
Control Nozzle position forward or backward.

SEAT TEMP/ WATER TEMP
5 levels of Water temperature Seat temperature.

POWER SAVE
It cuts off the power of water heater and seat heater. It minimizes the use of power.

NOZZLE CLEAN

• Press NOZZLE CLEAN button to have nozzle extend out (for cleaning)
• Press the button once again to have NOZZLE return to WASH-ready position.

CHILD MODE

•  LED displays the setting condition.
• User can use FRONT/REAR WASH functions without seat is pressurized.

Maintenance

Use Power Save

• Press POWER SAVE button to switch to different energy save modes.

• Pressing POWER SAVE once turns green LED on that maintains preset temperatures for 30 minutes, then shuts off water heater and keeps seat temperature at minimal level. Water/Seat heaters shut off after 24 hours.

• Pressing POWER SAVE twice turns red LED on that shuts off Water/Seat heaters immediately.

• To stop Power save function, press the button to turn LED off.
  In case user sits down while Power Save mode, then seat sensor turns ON, water heater and seat heater start working automatically up to the preset temperature. (It takes minutes to get to the preset temperature)

• As user stands up, seat pressure sensor turns off and Water/Seat heaters automatically return to Power Save mode.

• Washing and Drying continue to function while Power Save mode.

Clean the Nozzle

• Use soft cloth or toothbrush to clean the nozzle.
• Do not use Abrasive, Volatile detergent, Acid/Alkaline detergent. It may cause breakage or trouble.

NOZZLE CLEAN (Automatic)
Press and hold NOZZLE CLEAN button for seconds to initiate self cleaning process.

NOZZLE CLEAN (Manual)

• Press and hold NOZZLE CLEAN button for seconds to initiate manual cleaning process.
• Nozzle extends out for 2 minutes.
• Clean the nozzle using toothbrush.
• Do not pull out or push the nozzle forcibly.
• NOZZLE CLEAN function does not work while seat is occupied and pressure sensor is activated.
• NOZZLE CLEAN function does not work in Child mode.

Troubleshooting

When you think the product is out of order, refer to the following for immediate measures.

Power Supply

Trouble Possible Causes                                                       Solution

**** The unit is not working| Isn’t the power out or isn’t the circuit breaket off?| Wait until the power is restored. Or turn on the circuit breaker.
---|---|---
Isn’t the operation lamp on the display panel of the main body off?| Plug the power plug in the outlet.

FRONT/REAR/EASY BOWEL WASH Functions

Trouble Possible Causes Solution

Water pressure is weak| Isn’t the water pressure set to low level?| Adjust the water pressure to higher level.
---|---|---
Water is cold| Isn’t the temperature set to a low level? Or Is it turned off?| Adjust the water temp on the control panel.
Isn’t it in power save mode?| Press POWER SAVE button again to return to normal mode.
Water spray stops during use.| Water stops at 90 seconds after pressing any of FRONT/REAR/EASYBOWEL WASH buttons.| Press desired wash function one more time..
Seat sensor may not touch human body.| Check the position of seat sensor on page 5.

Heated Seat

Trouble Possible Causes                                                       Solution

**** The seat dose not warm up.| Isn’t the temperature of seat set to OFF or low level?| Control the seat temperature on controlpanel.
---|---|---
Isn’t the bidet in power save mode?| The seat temperature is set lower Press the Power save again.

Seat Sensor

Trouble Possible Causes Solution

Wash function works without sitting down.| Isn’t the seat wet or occupied by wet towel?| Wipe water out. Remove the wet towel.
---|---|---

Power Save

Trouble Possible Causes Solution

Power save is not working.| Isn’t the unplugged? Or isn’t the power out?| Press POWER SAVE button to initiate the function once power is restored.
---|---|---

Self Diagnosis

Trouble| Indication
LED lamp on main body of side control| Symptoms
---|---|---
Water supply stops or water level sensor is faulty.|  LED blinks

| Water not spray, warm water not spray
Water temperature sensor disconnected. short circuit| | LED blinks

| Warm water not spray
Seat temperature sensor disconnected. short circuit| LED blinks

| **** Seat not heated

Specifications

Warranty

Product Warranty Card

• We warrant our products to be free from manufacturing defects under normal use and service for a period of one(1) year after purchase. This warranty is extended only to the original purchaser.
• For product defect. please contact your vendor or our service center.

< Condition of No-Cost Repair/Replacement >

• During the duration of the warranty period, if product defect occurs during normal application as stated in the Instruction Manual, Cautionary Notes, Direction Labels, etc., the product is applicable for after-sales service free of charge.
•  Even during the warranty period, after-sales service is not applicable free of charge in case of the following conditions

1.  Damage occurring from customer negligence or fault, and defect or damage occurring from wrongful repair or alteration.
2. Defect or damage occurring from fire, gas, flood, earthquake, lightning,
3.  Defect or damage occurring from outside of normal household usage. (long term public usage, used inside a vehicle, installed inside a vessel, etc.)
4.  Defect or damage occurring from transportation of mistreatment after purchase.
5. Defect or damage occurring during removal after installation.
6. Wearing of consuming parts. (Packing, Filters, etc.)
7. Product reinstallation by customer request.
8.  Read the Instruction Manual carefully before requesting for an after-sales services since charges will be invoiced for faulty service call visits.

PHILTRE, Co.

https://philtre.life/Contact/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>