SFP 203C Electric Fireplace Stove Heater Owner’s Manual
- June 16, 2024
- SFP
Table of Contents
ELECTRIC FIREPLACE STOVE HEATER
SFP 203C
PRODUCT USE GUIDE
ELECTRIC FIREPLACE STOVE HEATER
OWNER’S MANUAL
203C Electric Fireplace Stove Heater
Thank you for choosing our Electric Fireplace Stove Heater. This user manual
will provide you with valuable information necessary for the proper care and
maintenance of your new product.
Please take a few moments to thoroughly read the instructions and familiarize
yourself with all the operational aspects of your new product.
INTRODUCTION
Please take a few minutes to read this manual carefully.
Proper maintenance and operation of this machine can provide better service.
IMPORTANT INSTRUCTIONS
When switching on the appliance for the first time, allow it to run at full power for about two hours to get rid of the unpleasant smell. Make sure that the room in which the appliance is located is well ventilated during this operation. It is normal for the appliance to emit small cracking sounds when you tum it on if the first time.
-
Read all instructions before using this heater.
-
This heater is hot when in use. To avoid bumps, do not let bare skin touch hot surfaces.
Use handle when moving the unit. Keep flammable materials such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front and top of the heater and keep them away from the sides and rear of the heater. Keep the rear grille away from walls or drapes so as not to block the air intake. -
Extreme caution and supervision is necessary when any heater is used near children or invalids and whenever the heater is left operating and unattended.
-
Always unplug heater when not in use.
-
Do not use any heater with a damaged cord or plug or after the heater malfunctions or has been dropped or damaged in any manner. Discard heater or return to an authorized service facility for examination and/or repair.
-
Do not use outdoors.
-
This heater is not intended for use in bathrooms, laundry areas or other similar indoor locations. Never locate heater where it may fall into a bathtub or other water container.
-
Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic areas and place it where it will not be tripped over.
-
To disconnect heater, tum controls to off, then remove plug from outlet.
-
This appliance has a polarized plug (one blade is wider than the other). This plug is intended to fit a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, consult a qualified electrician. Do not connect the heater to extension cords, surge protectors, timers, direct breakers, or an outlet with other appliances connected to the same outlet. Risk of fire, overheat, malfunction, property damage, injury, or even death may result if not adhered to
-
Connect to properly polarized outlets only.
-
Do not insert or allow foreign objects to enter ventilation or exhaust openings, as this may cause an electric shock or fire, or damage the heater.
-
To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
-
A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
-
Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, injury fo persons or other damage to property.
-
This heater must be plugged into a 120V, 15 amp (or more) circuit of its own. Nothing else can be plugged into the same circuit. If unsure if you home meets this specification, consult a certified electrician prior to use. Risk of fire, overheat, malfunction, property damage, injury, or even death may result if not adhered to
-
To prevent overload and blown fuses, be sure that no other appliance is plugged into the same outlet or into another outlet wired into the same circuit.
-
Itis normal for the heater’s plug and cord to feel warm to the touch. A plug or cord that becomes hot to the touch or becomes distorted in shape may be a result of a wom electrical outlet. Worn outlets or receptacles should be replaced prior to further use of the heater. Plugging heater into a wom outlet/receptacle may result in overheating of the power cord or fire.
-
Ensure the heater is on a stable, secure surface to eliminate the potential of tipping over.
-
Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet /power strip).
-
Be sure that the plug is fully inserted into appropriate receptacle. Please remember that receptacles also deteriorate due to aging and continuous use: check periodically for signs of overheating or deformations evidenced by the plug. Do not use the receptacle and CALL your electrician.
-
Check that neither the appliance nor the power cable has been damaged in any way during transportation.
-
Make sure that no pieces of polystyrene or other packaging material have been left between elements of the appliance. It may be necessary to pass over the appliance with a vacuum cleaner.
-
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction conceming use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
CAUTION : To prevent electric shock, match wide blade of plug to wide slot, fully insert.
PARTS & ACCESSORIES
Parts
Accessories
- Attention: (“+”) screwdriver (not included)
SPECIFICATIONS
| Model No. | SFP203C |
|---|---|
| Item Name | Electric Fireplace Stove Heater |
| Rated Voltage | 120V (60Hz) |
| Rated Power | 1500W |
| Two Setting | Low/High |
| Safy Protection | Overheat Auto-off |
| Heating Element | Heating Wire |
| Net Weight | 18.52 LBS |
| Product Size | 22.05×11.42×25 inch |
PRODUCT DIAGRAM
OVERHEAT PROTECTION
This heater is protected with an overheat protection that switches off the
appliance automatically in case of overheat, e.g. due to the total or partial
obstruction of the grids.
In this case, unplug the appliance, wait about 30 minutes for it to cool and
remove the object which is obstructing the grids. Then switch it back on as
described above.
The appliance should operate normally. Should the problem persist, please
contact the customer service.
ASSEMBLY INSTRUCTION
Attention: ALWAYS make sure the unit is unplugged before beginning assembly NEVER move or clean the heater, or change the bulbs, while it is plugged in.
-
Carefully tum the STOVE (A) upside down and lay it on a clean soft surface.
-
Insert the TAB of one LEG (B) into the SLOT in the comer of the stove frame.
-
Thread three SCREWS (C) through the holes in the leg and into the stove frame.
Partially tighten the screws with a Phillips screwdriver. -
Repeat Steps 2 and 3 for the other three legs.
-
Check the alignment and tighten all 8 screws securely with the screwdriver.
DO NOT over-tighten the screws.
ALWAYS attach the feet before using! NEVER plug in or operate this unit if the feet are not securely attached!
PREPARATION
Place the heater on a firm, level surface and plug into a 120V 60Hz power outlet. And tum on the power switch in the rear of the unit. Insert 2 AAA batteries into the remote control before using (Batteries Not Included)
OPERATION FUNCTIONS
Control Panel: Located at the lower right comer of the insert. Open the door to access it.
OPERATING YOUR HEATER
Control Panel Functions
| CONTROL | OPERATION / FUNCTION |
|---|---|
| ON : Press the power switch ON. The power indicator light will glow, and the |
flame effect will tum on.
OFF: Press the power switch OFF. All functions will tum off.
FLAME INTENSITY| FLAME INTENSITY : This knob controls the brightness of the
flame effect. Tum the knob to the right (High) to brighten the flame |
effect.Turnthe knob to the left (Low) to dim the flame effect.
| ( NOTE : The ON/OFF switch tumn the flame effect on and off.
The flame effect will not turn off unless the power is turned off. )
| THERMOSTAT : This knob controls the thermostat that tums the heat on and off
to maintain the desired temperature.
Tum the knob to the desired setting. The heat will tum on and off
automatically to maintain the set temperature.
To lower the temperature, rotate the knob further counter-clockwise towards
the LOW(left) position.
To raise the temperature, rotate the thermostat knob clockwise . ds the
HIGH(right) position
( NOTE : If the room temperature is higher than the thermostat setting, the
Thermostat heater will not turn on. )
NOTICE| When the heat function is used for the first time, a slight odor may
be present. This is normal and should not occur again unless the heater not
used for an extended period of time.
CARE AND MAINTENANCE
ALWAYS turn the heater OFF and unplug the power cord from the outlet before
cleaning, changing the light bulbs, or moving this stove. Failure to do so
could result in electric shock, fire, or personal injury.
NEVER immerse in water or spray with water. Doing so could result in electric
shockfire, or personal injury.
Risk of electric shock ! DO NOT OPEN the main panels
No user-serviceable parts Inside
CLEANING
Metal : Buff using a soft cloth, slightly dampened with a citrus oil-
based product.
DO NOT use brass polish or household cleaners as these will damage the metal.
Glass : Use glass cleaner and dry thoroughly with a paper towel or lint-
free cloth.
NEVER use abrasive cleansers or any cleaner that could scratch the surface.
Plastic : Wipe with a slightly damp cloth and a mild solution of dish
scup and warm water.
Vents : Use a vacuum or duster to remove dust and dirt from the heater
and vent areas.
STORAGE
Store heater in a clean dry place when not in use.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>