2BDC6-SHELLYBLUDW BLU Door Window Installation Guide
- June 15, 2024
- Shelly
Table of Contents
2BDC6-SHELLYBLUDW BLU Door Window
Product Description
- A: Light sensor
- B: Control button
- C: Magnet
- D: Sensor unit
USER AND SAFETY GUIDE
Shelly BLU Door/Window
Read before use
This document contains important technical and safety information about the device, its safe use and installation.
CAUTION! Before beginning the installation, please read carefully and entirely this guide and any other documents accompanying the device. Failure to follow the installation procedures could lead to malfunction, danger to your health and life, violation of law or refusal of legal and/or commercial guarantee (if any). Shelly Europe Ltd. is not responsible for any loss or damage in case of incorrect installation or improper operation of this device due to failure of following the user and safety instructions in this guide.
Shelly® devices are delivered with factory-installed firmware. If firmware updates are necessary to keep the devices in conformity, including security updates, Shelly Europe Ltd. will provide the updates free of charge through the device Embedded Web Interface or the Shelly mobile application, where the information about the current firmware version is available. The choice to install or not the device firmware updates is the user’s sole responsibility. Shelly Europe Ltd. shall not be liable for any lack of conformity of the device caused by failure of the user to install the provided updates in a timely manner.
Product Introduction
Shelly BLU Door/Window (the Device) is a Bluetooth sensor designed to detect the opening and closing of a door or window. It can also measure the inclination of a door or window that tilts and turns. In addition, it features a light sensor.
Installation Instructions
WARNING! Do not allow children to play with the magnets. Even relatively
small magnets can cause serious injury if swallowed.
CAUTION! Keep the Device away from liquids and moisture. The Device
shouldn’t be used in places with high humidity.
CAUTION! Do not use if the Device has been damaged!
CAUTION! Do not attempt to service or repair the Device yourself!
CAUTION! The Device may be connected wirelessly and may control electric
circuits and appliances. Proceed with caution! Irresponsible use of the Device
may lead to malfunction, danger to your life or violation of the law.
First steps
Shelly BLU Door/Window comes ready to use with the battery installed.
However, if pressing its button does not make the Device start emitting
signals, you might need to insert a battery.
See the Replacing the battery section.
Mounting
ATTENTION! When mounting the Device make sure the small triangle on the sensor unit points towards the magnet as shown in Fig. 2 and the distance between the sensor unit and the magnet is less than 10 mm / 0.4 in when the door or the window is closed.
You can place the magnet left, right, above, or below the sensor unit.
If you want to monitor a door or window that tilts and turns, mount the sensor
unit (C) on the door or the window (A) and the magnet (D) on the frame (B) as
shown in Fig. 3.
Use the supplied double-sided foam stickers to affix the sensor unit and the
magnet to the door or the window and the frame. Depending on the door or
window frame, you may need to align the magnet and sensor unit by raising one
of them using shims (E).
If you want to monitor a conventional door or window, we suggest, if possible,
mounting the sensor unit on the frame and the magnet on the door or the
window.
- Fig.3/Abb.3
Using Shelly BLU Door/Window
If a conventional door or window is opened, the Device will immediately broadcast information about the event, the illumination, and the battery status at the time of the opening detection.
If a door or window, which tilts and turns is opened, the Device will immediately broadcast information about the event, the illumination, and the battery status at the time of the opening detection and 2 seconds later will broadcast information containing the inclination angle, the illumination, and the battery status at the moment. If the inclination angle changes the Device will broadcast its new status within 8 seconds.
If the door or the window is closed the Device will broadcast information about the event, the inclination angle (zero), the illumination, and the battery status at the time of the closing detection.
If the Device beacon mode is enabled it will broadcast information about the current open/close state, the inclination angle, the illumination, and the battery status every 30 seconds.
To pair Shelly BLU Door/Window with another Bluetooth device press and hold the Device button for 10 sec.
The device will await connection for the next one minute. The available Bluetooth characteristics are described in the official Shelly API documentation at https://shelly.link/ble
To restore the device configuration to factory settings, press and hold the button for 30 seconds shortly after inserting the battery.
Initial Inclusion
If you choose to use the Device with the Shelly Smart Control mobile
application and cloud service, instructions on how to connect the Device to
the Cloud and control it through the Shelly Smart Control app can be found in
the mobile application guide. The Shelly mobile application and Shelly Cloud
service are not conditions for the Device to function properly. This Device
can be used standalone or with various other home automation platforms which
support BTHome protocol.
For more information visit bthome.io
Replacing the battery
-
Open the back cover as shown in Fig. 4.
-
Extract the exhausted battery by first pushing it through the battery holder cutout and then pulling it out as shown in Fig. 5.
-
Slide in a new battery as shown in Fig. 6
CAUTION! Use only 3 V CR2032 or a compatible battery! Pay attention to the battery polarity! -
Replace the back cover by pressing it to the sensor unit at the four angles until you hear a clicking sound as shown in **Fig. 7.
**
Troubleshooting
In case you encounter problems with the installation or operation of Shelly BLU Door/Window, please check its knowledge base page: https://shelly.link /blu-dw_KB
Specifications
- Dimensions:
- 35x35x7 mm / 1.38х1.38х0.27 in (sensor unit)
- 35x12x7 mm / 1.44х0.47х0.27 in (magnet)
- Weight:
- 10 g / 0.35 oz (sensor unit with battery)
- 8 g / 0.28 oz (magnet)
- Working temperature: -20°C to 40°C
- Humidity 30 % to 70 % RH
- Power supply: 1x 3 V CR2032 battery (included)
- Battery life: 5 years
- Radio protocol: Bluetooth
- RF band: 2400 – 2483.5 MHz
- Max. RF power: < 4 dBm
- Beacon function: Yes
- Encryption: AES encryption (CCM mode)
- Operational range (depending on local conditions):
- up to 30 m outdoors
- up to 10 m indoors
Declaration of conformity
Hereby, Shelly Europe Ltd. (former Allterco Robotics EOOD) declares that the radio equipment type Shelly BLU Door/Window in compliance with Directive 2014/53/EU, 2014/35/EU, 2014/30/EU, 2011/65/EU. The full text of the EU declaration of conformity is available at the following internet address: https://shelly.link/blu-dw_DoC
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Customer Support
Manufacturer: Shelly Europe Ltd.
Address: 103 Cherni vrah Blvd., 1407 Sofia, Bulgaria
Tel.: +359 2 988 7435
E-mail: support@shelly.cloud
Official website: https://www.shelly.com
Changes in the contact information data are published by the Manufacturer on
the official website. https://www.shelly.com
All rights to the trademark Shelly® and other intellectual rights associated
with this Device belong to Shelly Europe Ltd.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>