ZBM MAGNER 125 Machine fcor Testing and Counting Money User Manual

ZBM MAGNER 125 Machine fcor Testing and Counting Money

Specifications

• Product: MAGNER 125
• User Manual Version: V1.0
• Email: info@zbm.co.il
• Phone: 1-700-500-717
• Website: https://www.zbm.co.il

Introduction

Preface

• Thank you for purchasing our MAGNER 125 product. This user manual provides detailed operation steps and important information to take note of.
• To ensure correct usage, please read this manual carefully. If you encounter any difficulties, please contact your local distributor immediately.
• We reserve the right to modify the content of this manual without prior notice.

Declaration

• This product is designed for sorting and counting banknotes. Any loss or damage caused by incorrect usage or modifications not authorized by our company or distributor will not be covered by our company. Please contact your distributor for assistance with installation or transportation to prevent incorrect installation or damage during transportation.
• This product is specifically intended for counting and sorting banknotes as mentioned in the user manual. Please do not use this machine for any other purpose.
• Due to different power supply standards and safety regulations, please do not use this machine in countries with incompatible power supplies.
• Some content in this manual may be subject to modification without prior notification. We appreciate your understanding.
• We are continuously working to improve the quality of our products, so the actual machine may differ slightly from the manual.
• If the machine is altered or modified by the user without our notice, our company will not be held responsible.

FAQ

Q: What is the purpose of the MAGNER 125 machine?

A: The MAGNER 125 is designed for sorting and counting banknotes.

Q: What should I do if I encounter difficulties with the machine?

A: If you face any difficulties, please contact your local distributor immediately for assistance.

Q: Can I use the MAGNER 125 for purposes other than counting and sorting banknotes?

A: No, the MAGNER 125 should only be used for counting and sorting banknotes as mentioned in the user manual.

Introduction

Preface
Thanks for buying our product. The user manual includes the operation steps and matters need attention. In order to use the machine correctly, please read this manual carefully. If you meet any difficulty please contact your local distributor immediately. We keep the right to modify the content of the manual without notice.

Declaration
This product is used to sort and count banknotes ,If any loss caused due to incorrect use, or any modification to the machine not done by our company or our distributor, our company will not be responsible for it. Please contact your distributor if you want to install or transport this machine to avoid the wrong installation or damage during the transportation.

• This product is used for counting and sorting the mentioned banknotes in user manual. Please don’t use this machine for other purpose.
• Due to different power supply standard and safety standard, please do not use this machine in countries with disaccorded power supply.
• Some content may be modified without notification, please kindly understand.
• We are working continuously for improving the quality of products, so the actual machine may be a little different with the manual.
• If the machine is changed or modified by user without our notice, our company will not be responsible for it.

Installation Notice

Installation Notice

1. If you need to install this product, please contact the nearest distributor or our authorized distributor.
2. The machine is only suitable for indoor use, please do not install it and use it outdoor.
3. Please install the machine in an even place which can hold the weight of this machine.
4. Please do not use or put flammable or volatile items around the machine, such as diluents.

Installation and Operation Place

Install the machine as below picture, there should be enough space for your operation, such as putting the notes, opening and closing the cover and doing maintenance.

Diagram

Back Appearance

Top Appearance

Specification

100 currencies(Max)

Countable notes size| Length：100mm~180mm

Width：50mm ~90mm

Countable notes thickness| 0.05mm~0.12mm
Counting Speed| 800/1000/1200pcs/min （ MIX & SDC

mode）

800/1000/1200/1500pcs/min   （ CNT

mode）

Counting Mode| MIX, SDC, CNT
BATCH| 0~200
Counterfeit detection| UV/MG/MT/IR
Power supply| AC 220V 50Hz   ±10%

AC 110V 60Hz   ±10%

Noise level| 60-75DB
Power consumption| Standby≤15W

Operation≤50W

Working environment| Environment                    temperature

（0~40°C)/humidity（40~90%）

Air pressure（70-106kpa)

Storage environment| Environment temperature（-40~55°C)/ humidity （ 10~95% Air    pressure

（70-106kpa)

Appearance and Key Panel

Display Appearance

Function key

User Interface and Touch key

Operation introduction

Operation introduction
Connect the machine with electricity and then turn on the machine, it will enter below self-check interface as below pictures,

Wait about 1 minute for this process, then the machine will enter below main interface.

Accumulation Mode (ADD)

ADD ON

Under any counting mode, press to turn on accumulation function, it will show “+” on display as below picture.

• a） After finish counting a bundle of notes and the notes are not removed, the machine displays the amount and quantity of this bundle of notes; if the notes are removed, the latest counting data will be accumulated to historical data and the machine will display the accumulated total data.Press CLR key it will clear the latest counting data, press CLR twice it will clear the total data.
• b） During the counting, if some abnormal situation happens such as jam, the machine will delete the current counting data.
• c） In ADD mode, when you check the serial number details, the machine will only show the serial number of latest 200 notes.

ADD OFF
Press key to turn off the ADD function, it will show OFF as below picture，When this function is off, if you put another bundle of notes on hopper to count, the quantity will start from 0.

Choose Currency
Press key or press the country flag on touch screen, the machine will enter into currency choice menu.

After choosing currency, it will enter into main interface; if you want to cancel, please press to exit. means it is in active mode, which is the currency mode before you change.

Working Modes

Mixed Denomination Counting (MIX)
In this mode, all the denominations can be recognized and counted, calculating the quantity and amount at the same time. Serial number can also be recorded if you turn on the serial number reading function. You can check the serial number details under another interface.
Under Multi-currency counting mode, the display will show the total amount and total quantity for each currency.

Single Denomination Counting (SDC)
This mode is mainly for counting the same denomination notes, for example, to count the same denomination already sorted. The machine will stop when it recognize a different denomination, you need to remove this note and continue counting. The machine recognize the first note and count following notes based on this standard, thus, when version sorting is turned on, it will stop when it recognize a different version.
Under this mode, the machine can also calculate amount and quantity, as well as serial number reading.

Piece Counting Mode (CNT)
In this mode, it will not calculate the amount, only calculate quantity. When ADD function is not turned on, it will only display the current counting quantity; when ADD is turned on, it will display the current counting quantity and accumulated counting quantity.

NOTE: under MIX&SINGLE mode, the machine checks the notes by image, MG, UV and DB(double notes detection), under COUNT mode only has DB detection.

Speed Set
Press key to adjust the speed.

SDC(Qty & Amount)

MIDDLE| CNT(Qty only)

MIX(Qty &Amount, serial number reading turned on) SDC(Qty & Amount, serial number reading turned on)

LOW| MIX(Qty   &Amount,   serial   number   reading   turned   on,
| Mix-currency counting, Auto recoginition)

SDC(Qty   &Amount,  serial   number   reading   turned   on, Mix-currency counting , Auto recoginition)

---|---

The speed shown as below picture.

Check counting list & print

Counting list

Check the counting list
Press key one time to display the quantity and amount When ADD is on, if the notes are not removed, it will show current amount and quantity; after remove the notes, it will accumulate the latest bundle of notes data to previous data.

Check the serial number
Press key twice to check the serial number.
The serial number is available to check when speed is set at 800-1000pcs/min, and you can only check the serial number of latest 200pcs notes.

Print Function
Thermal printer is recommended to connect with machine through RS232 port. You can set the baud rate under SET mode, the default baud rate is 115200.

Print quantity and amount.
Under List interface, press key and the printing receipt is shown as below

Print serial number
Under serial number list, press key, the receipt is shown as below.

Set Menu

Press key to enter into MENU，it includes 2 elements: Customize and Basic

Customization
This menu includes Counterfeit detection level setting, Batch setting and Start Mode setting.

Detection level
There are three levels for your choice, High, Middle and Lower. You can choose by pressing the . The Unser defined detection is set by factory or distributor according to field test result, it is not suggested to be changed by user directly.

Batch Qty
Shown as below picture, there are 6 default Batch number for your choice, you can also revise the number as desired. Please press CONFIRM button to return to main interface after choice.

Start Mode
As shown by below picture, you can turn on or off the Auto Start function.

Auto Mode: When Auto Start is turned on, it means the machine will start counting automatically when notes are put on the hopper
Manual Mode: When Auto Start is turned off, it is in Manual Mode, you need to press START key manually after put the notes on hopper.

Basic Setting
Click General to enter Basic Setting as below picture , you can set Date&Time, Buzzer, Alarm, Serial Port, Version Information, Language, Restore Factory Setting,

Date & Time
Under basic setting interface, touch Date&Time item to enter into date/time setting interface.

Under this interface, touch the corresponding number, touch +, it will increase by 1, touch -, it will decrease by 1

Touch the corresponding number two times, it will enter into modification interface, shown as above picture, you can input number

directly, touch to save, touch to delete.
Under Date&Time setting interface, click to enter below interface,

Under this interface, you can choose to set Year, Month, Date.

Buzzer Setting
Under Basic Setting interface，touch Buzzer’s switch to turn this function on or off.

Serial Port setting
Under Basic Setting interface，touch Serial Port to enter into baud rate setting interface.

According to the actual situation of external device, touch 9600 or 115200 to choose baud rate. Please press CONFIRM button to return to main interface after choice. The default setting is 115200.

Software version
Under Basic Setting interface，touch Version info item，to enter into software version checking interface.

Language setting
Under Basic Setting interface, touch Language item to enter into language setting interface, as shown by below picture, touch the corresponding language to choose, choose OK and restart the machine to effect.

Restore factory setting
Under Menu interface to touch Reset item, it will show as below

• Touch item press OK then all the counterfeit detection level will return to factory default setting;
• Touch item, ress OK, then all the basic setting will return to factory setting.

Common trouble shooting

During operation, the machine may occur some abnormal situation then it can not working properly, usually it will show ERROR code on display. Below are the ERROR code information, please make trouble shooting according to service manual. If still could not be solved, please contact your local distributor.

System Error code

Counting Error code

warning message| code
IMG-UNKNOW| 51
IMG-FAKE| 151-159
UV-T| 203
UV-R| 202
MT| 351
MG-Q| 463
MG| 471-482
OCR-UNKNOW| 501
ANGLE（incline）| 551、555
DAMAGE（damage）| 552
GAP(chained notes）| 553、556
HALF（damage）| 554
DOUBLE（double notes）| 557
ORT-ERROR| 901

Software upgrading

This machine uses USB driver to upgrade software, before upgrading, please copy the software(for example：BC55_1_20180413.DF61CBFADD1A723E.ZPK）into the root directory of USB(please do not change the name or format of the file, and do not put 2 or more software into the root directory), then insert the USB driver into the USB port at the back of the machine.
Turn on the machine, machine will recognize the software automatically, after recognize successfully, it will display “Upgrade pack is found, update after 5 seconds”，after 5 seconds, it will display “Updating”，the upgrading will finish within one minute, and it will display “Update completes, Please remove the Udisk and reboot. It means upgrading is successful and please restart the machine.

Daily Maintenance

Any dust, dirty objects or other substances can stick to the sensors and disturb the normal work of the sensors and then cause inaccurate counting result, so please clean the sensors and rollers everyday with the provided cleaning kit.
Please turn off the power switch before starting the cleaning in order to avoid any risk of electric shock or other injury.
Please do not use any chemical agent or water such as benzene, thinner which may cause the color fading or crack of the machine.

Clean the hopper sensor
As shown by below picture, use nylon brush or cleaning cloth to clean the hopper sensor (QT sensor)

Clean the drum roller and friction roller
As shown by below photo, use nylon brush or cleaning cloth to clean the drum roller and friction roller

Clean the stacker sensor
As shown by below picture, use nylon brush or cleaning cloth to clean the stacker sensor (ST sensor)

Clean the inner sensor

1. As shown by picture, pull the back cover and open it.
2. As shown by below picture, use nylon brush to clean the lower UV sensor and lower CIS.
3. As shown by below picture, use nylon brush to clean upper UV sensor and upper CIS.

Accessories

1. Power cord 1pc
2. Nylon brush 1pc
3. User manual 1pc
4. External display（option） 1unit
5. External printer（option） 1unit
   ***We keep the right to modify the contents of this manual for continuous improvement of our device.

info@zbm.co.il
1-700-500-717
https://www.zbm.co.il

References

• מערכות אבטחה ותקשורת: חנות אונליין למוצרים בתחום האבטחה | זד בי אם
• מערכות אבטחה ותקשורת: חנות אונליין למוצרים בתחום האבטחה | זד בי אם

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>