Jimdary B0BN74D725 Instant Electric Water Heater Instruction Manual

B0BN74D725 Instant Electric Water Heater
Instruction Manual

B0BN74D725 Instant Electric Water Heater

Operation Standard: EN 60335-2-35 2016
EN 60335-1.2012+411:2014and
EN 62233.2008

• please read this instruction manual carefully before using
• Please keep this instruction manual in good

Packing List

Product model| WY-XCB001, WY-XCB002, WY-XCB003. WY-XCB004. WY-XCB005,| WY- XCB006, WY -XCB011, WY-XCB007, WY -XCB012. WY-XCB008, WY-XCB01 3, WY-XCB009, WY-XCB01 4. WY-XCB010, WY-XCB015.| WY-XCB016, WY-XCB01 7, WY-XCB018. WY-XCI301 9, WY-XCB020,
---|---|---|---
Product| | 1 Pc|
Accessory| | 1 Set|
manual| | 1 Pc|

Product summary and functional characteristics

This product carries out EN 60335-2-35.2016 and EN 62233.2008 EN 60335-1:2012+A11:2014 and standards, other related and has passed CE certification
This series products adopts advanced flow control switch technology, Make sure that the water is switched off immediately. It has no electromagnetic Foxing, green environmental protection, no pollution, microcomputer automatic control system. The product has fault self checking function LED digital display current working state. Personalized memory function, boot display last working state. open-use, Easy to save and fast heating, No capacity limitation, Without preheating, avoid heat loss caused by long preheating process. Energy saving ,Double temperature intelligent control system, anti overheating and dry burning protection device, Built in double circuit breaker anti leakage protection device, at the same time matching external electric protection wall, multiple protection to ensure safety.

Product Main technical parameters

Style No| Rated power| Rated voltage| Rated water pressure| wire require comments|
---|---|---|---|---|---
Please select the detail according to the rated power.| 3400W| 220V —| 0 MPa| 1.5mm²| 0.05MPa-0.6MPa
4500W| 220V —| 0 MPa| 2.5mm²| 0.05MPa-0.6MPa
5500W| 220V —| 0 MPa| 2.5mm²| 0.05MPa-0.6MPa
6050W| 220V —| 0 MPa| 4mm²| 0.05MPa-0.6MPa
7000W| 220V —| 0 MPa| 4mm²| 0.05MPa-0.6MPa
8500W| 220V —| 0 MPa| 6mm²| 0.05MPa-0.6MPa
10 kW| 380V —| 0 MPa| 1.5rtim•x5| 0.05MPa-0.6MPa
12 kW| 220V —| 0 MPa| 10mm²| 0.05MPa-0.6MPa
12 kW| 380V —| 0 MPa| 2.5m rrix5| 0.05MPa-0.6MPa
15 kW| 380V —| 0 MPa| 2.5mrwx5| 0.05MPa-0.6MPa
18 kW| 380V —| 0 MPa| 4 mrrYx5| 0.05MPa-0.6MPa
24 kW| 380V —| 0 MPa| 6mmIx5| 0.05MPa-0.6MPa

Electrical principle diagrammatic sketch

Installation instructions

1. This product must be installed by quaffed professional persons.
2. Prepare impact drab(n° drill bit is 6A1M in diameter) .Adjustable wrench, cross saewdriver. electric knife. etc.
3. Check whether the meter, air switch, wire meets the requirements, and whether the earth wire is actually introduced into the ground. 1)Ground wire must be fully grounded. 2)Be sure to install an air switch with leakage protection
4. Refer to the length of the power cad and the position of the air switch, to determine the installation hole of the product on the wall with a pencil to mark the position of the two screw uncles. Saw on the mooning screw and keep a distance of about 3mm from the wall, then hang up the water heater, and then screw in one of the lower fixing screws.
5. Conned the copper-cored power Fire line L(brown color or red color ), zero line N(blue color), ground knee(yellow green knee )to the corresponding are switch or terminal and tighten it to ensure a reliable connector.
6. Connect the users water supply pipe (conned to the flow valve) to the machine inlet. One end of the outlet hose is connected to the outlet of the ma: Sward the other end a connected to the bed seal of the flower &kidder.
7. If its new installed pipe , for the first time install, the impurities in the pipe must be emptied before it can be connected to the machine,
8. Anti dropping screws are mounted on the top of the machine to prevent the machine from falling due to accidental contact.

Attention: Each water pipe pint must be encrypted with sealing gaskets When wrenching the water pipe with a wrench, the force should not be too quick or too nocent to eyed damaging the machine.

This installation diagram is not necessarily consistent with your purchase of the actual product, only for the installation instructions. 5.using Instructions
For the first using or tap water is stopped . tum off the electricity first .Then tum on the water outie switch. When the shower sprinkler has a continuous water outlet, i can be electrified. (f not operate foe this way . lt is possible to damage  the machine.) 1LED display
Power on display
Digital screen standby dark ight, When it ls on for 3 tong tne, it is display the water outlet temperature status,
and when it is flashing, it is the sel temperature status. Quill after 10Swithout operation
When heating, the screen flashes, it indicating that the water flow is small or the temperature is high.
When display LL ° . ¢ means the water flow is large and the temperature is too low.
When display ° E~ . it indicates that there is a fault in the self-test of the product, and the heating is stopped at this time.
When display “ – °, & indicates shutdown status, indicating shutdown withoul hasting.
When display “.o. & means, The voltage is below 160%, the voltage is too low, and the Mache stops heating,
When display Lo It mesons, The ambient temperature & less than 5’C . Ties symbol agemates display with
water temperature, but does not affect the work of the machine.
When display “on 0 means, The water temperature exceeds 55 C , the machine stops heating, and when the water temperature is
below SSC , the machine returns to standby heating.
When dap lay¢s tt means, The machine installed in the wrong direction and the machine stopped working.
A dormant state: When the machine button is not operated, of the machine is not working, the duple is closed after 305. When there is
Operation or water flow through, the deploy screen is on.
Ternperature setting range: 35-45 °C ; some models are 35-55 °C , 20-55’C duskiest to the actual machine).
All machines have the function of power outage memory. After powering, the machine wall restore the parameters set before power outage.
2)Touch Key
@ Temperature setting kay, cycle setting temperature or mode try
@ Power standby key. press 3% 10 turn on of Mandy
BUN Che temperature kay Turn up and set the temperature.

Lowes the temperature hey. turn Gown and set the temperature

• Temperature shortcut key, fest set 35 C
• Temperature shortcut bey, facts 38 T
• Temperature sonicate bey, fast set 42T
• Temperature srortcuttay, fact set 45 ©
• Teem wrature shortcut bey, fast set SGC
•  Temperature setting bey nod brie, prow 36 to turn on oF off and fast grass to set the temperature es The repave menu hey © guided by 2 professional, arid this menus! is not interpreted.

Attention Warning:

If the water heater is likely to freeze in the environment, please turn off the water inlet and do not connect the power to the product. Prevent safety and property damage caused by freezing and water leakage. To avoid hazards arising from false resetting of the thermal cut-out, the appliance must not be powered by external switching devices; broken circuit.

1. Before installation, please ask a professional to check in deli whether the wire and meter capacity of the power supply line meet the requirements of the machine.
2. Are liable grounding wire must be installed. If there is no qualified grounding wire or the grounding wire is invalid, do not use the machine.
3. The fixed wiring must be in accordance with the wiring rules: it is equipped with a contact distance that can provide a leakage protection switch with all-pole disconnection under the conditions of overvoltage level 3. Please turn off  the leakage switch when not in use for a tong time.
4. If the power cord is damaged, in order to avoid danger, it must be replaced by professionals in the manufacturer’s maintenance department or similar departments.
5. Do not use any socket converters, etc. to adapt to theinslaliation of the electric water heater, and the use of power strips is prohibited.
6. The machine must be installed upright, and the test machine can only be powered on after the waterway is connected; the machine should not be placed too close to inflammables and strong magnetic fields.
7. This product is  forbidden to be installed outdoors, only used indoors.
8. The water outlet of the machine shall not be connected to any water valve or joint that is not approved by the manufacturer.
9. Stop using it in the environment below <0 ‘<32T, and turn off the water inlet. It is strictly forbidden to connect water and electricity to this machine.
10. Do not scrub the casing of the machine with acidic or alkaline cleaning solution, choose a neutral cleaning agent and disconnect the power supply when you need to scrub.
11. Children and the elderly must use it under the guidance of people who are familiar with the operation of the product.
12. The applicable water pressure range of this product: 0.05-0.6MPa. For models equipped with installed hoses, you must use the new hose assemblies that come with the machine. Japanese hose assemblies cannot be reused.
13. If an appliance with a nozzle is used at the water outlet of the water heater, the nozzle must be descaled regularly.
14. If you need to increase the use of a partition wall, you must install the randomly configured partition wall.
15. Do not spray Walter on the fuselage during use to prevent electrical components from getting wet.
16. When the valve is just opened. do not point the direction of the water to the human body.
17. Do not disassemble the machine by yourself. and do not replace the parts on the water heater without authorization.
18. The plastic probe on the water inlet and outlet joints of the machine is only  used lo prevent the leakage of residual water from the internal test during product transportation, and cannot be used for other purposes.

Common failure analysis and processing method.

connection is not good
B: Damage of rubber washer at junction| A: Reconnection pipe B:change rubber washer
The water is too hot| A:The water flow s too small or the position is too high.
B pipe blockage| altoist water valve to increase water flow or bet portion ,’ temperature B:Dean the egetfrier screen aril shower
The water is too cold| A:The water flow is too big or the position ts too low Blow Gnd voltage| A :Adjust water valve to reduce water flow or Upscale position if the supply voltage is too low.
Water temperature is hot and cold.| Instability of voltage or water pressure| The voltage ., water pressure is restored to normal.
The water flow is getting smaller and smatter.| Ater fitters or sprinklers are dogged with water.| Remove water pipe and dean filter screen / shower
Leakage switch trip| A: Electing leakage
B:Leakage switch aging
C Leakage current is too small| A Please do not use it and send ri io after tares white
B change teak age watch
Charge to large current leakage 50.-.):r
Display code E'(‘=0 9)| Internal sensor fault| contact with seller
Display without display| The power is not connected. B:The display monitor is damaged,| A Close switch on power supply
B: change display monitor
Display does but not heat| A. The inlet and outlet direction connection is wrong
B. The water flows too tittle
Mater flow sensor stuck| Corned tie inlet and outlet ports erectly Gladys the flow of water
C Contact customer service or seller
Flow : A: Light on
Excessive flow of water B: Gifting| A:The water flow is too large arc ate temperature is not enough. B:The water flow is small and the temperature is too high.| A-Reduce water flow Adjustment tit; water flow

• Warning: The failure can not be ruled out according to this prompt. Please stop using and close the main power supply, and send it to the local after sale maintenance treatment in time.

Certificate
Inspector
Production date

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>