UTEIWF 470 Shower Doors Frameless User Manual

INSTRUCTION
MANUAL

PARTS LISTING

DSO1

Please keep this manual and product code number for future reference and for ordering replacement parts if necessary.
PARTS LISTING

| Aluminum punch template (If missing or broken, please refer to page 8 for punch data.)| | Wall Bracket
---|---|---|---
| Anti Collision Block| | Roller
| Towel Bar| | Guide Block
| Anti Jumping Knob| | Screw & Allen key
| Guide Rail| | Door Seal
| Glass| | Anti-Splash Threshold

NOTES BEFORE INSTALLATION

1. Prepare the tools. (Please refer to page 6)
2. All measurements and installation should do after the wall and shower base were completed.
3. Make sure shower base is horizontal and both wall are vertical, if shower base not horizontal or the wall not vertical, please contact our installation support.
4. Understand the names and uses of individual accessories of shower doors. (Please refer to page 2~4)
5. Installation by licensed professional contractor is recommended.
6. Please watch installation video or call us for installation support. ( Link:https://youtu.be/EdaR3YgguuQ)
7. To stretch width or cut the guide rail, Please contact us first to get installation support.
8. Do not remove the glass protective corner during installation.
9. Tile walls are best to replenish some glass glue at the tile seams to avoid leakage after the installation is completed.

TOOLS REQUIRED

(Please bring your own tools)

| (we offer) Aluminum punch template| | Spirit level
---|---|---|---
| Tape measure| | Power drill
| Screw driver| | Drill Bits 5/16″ & 1/4″
| Pencil| | Rubber hammer
| Hacksaw| | Silicone Gun Modified Silane(Silyl) Polymer

INSTALLATION STEPS

1. According to the assigned aluminum punching template (please measure with horizontal ruler), draw the punching point position after ensuring the slope value.
   Product Height| X| Y
   ---|---|---
   60″| 55-9/16| 7/8″
   66″| 61-9/16| 7/8″
   72″| 67-9/16| 7/8″
   76″| 71-9/16| 7/8″
   79″| 74-9/16| 7/8″

*Same punching data for both walls

2. Drill the holes according to the drawn holes, making sure that there is no offset of the holes. The drilling positions of the left and right walls need to be in alignment and on the same horizontal and vertical plane.The vertical surface of wall bracket drilling position is 1 5/8″ away from exterior vertical surface of your threshold.
3. If the guide rail need to be cut to match your shower opening please do it based on actual measurements. If stretch the product installation width please adjusting the insertion depth of the wall bracket to the guide rail without cutting the guide rail. DS01 has maximum installation width stretch of 1″ for each size.
4. After the installation of the guide rail, please use the level ruler to measure whether the level.
5. After installing the rollers, hang the door on the guide rail
6. Installation of sliding glass: The height and level of the glass can be adjusted slightly by adjusting the rollers, through this adjustment can be adapted to the shower with a little wall offset, each wall offset preferably not more than 1/4″.
7. After the glass installation is completed, please measure the glass with level ruler to confirm the vertical and horizontal of the glass and then install the glass guide block.
8. Please follow the guide to install the handle and anti-jumping knobs. Anti-jumping knobs do not completely close to the guide rail, need leave slight gap to avoid sliding unsmooth.
9. The door seal can be installed according to your preference, but you need to ensure that there is minimum a wide door seal in the middle when you shower, The top of wide door seal needs to be slightly lower than the bottom of anti-jump knobs to avoid scraping. All door seals should be installed starting from the bottom and working upwards
10. Install the anti-splash threshold according to the guidelines, please cut to the right size according to the width of your shower opening. Clean up the garbage and dry the water and stains with a soft cloth after installation,then applying the glass glue.

Note: Please dry for 24 hours after the glass glue is applied before use.

SAFETY TIPS:

1.  Do not remove the glass protection corners during installation, remove them only after installation is complete.
2. Wear protective equipment when drilling, cutting guide rail and anti-splash threshold.
3. Careful installation of the glass is required during installation, please do not step on the glass to avoid bumping.
4. Wait 24 hours after installation before using the shower.

SHOWER DOOR MAINTENANCE AND CARE:

1. Shower door glass is double-sided easy-clean glass. For daily cleaning using moist soft cloth to wipe away surface water and stains, reduce the use of cleaning agents to extend the easy-clean performance. It’s recommended to use soft cloth to clean the residual water stains on the glass and hardware after shower. Silicone squeegee is available.

2. Do not use any sharp cleaning tools or cleaning agents with abrasive ingredients to clean the glass.

3. Caustic cleaners should not be used, such as alcohol. Long-term use of corrosive cleaners will cause discoloration of the hardware.
   Reducing the use of cleaners will prolong the use of the hardware&glass appearance. You can use small amount of anhydrous ethanol or detergent to clean stubborn water stains or calculus on the hardware.

4. Do not let the shower water directly wash the bottom of inner door.

TROUBLESHOOTING GUIDE AND NOTE

Shower doors don’t close tightly issues:

Q1: When | close the door, the door closes then backs out and never closes tight. How should I do?

A1: First please check that the anti collision block is installed on both sides, it will hold the glass in place when closing the door to keep it closed. Then use a level to check your guide rail and glass level status, if not installed level, you can adjust the top roller to adjust the sliding glass level and height. Even if your guide rail is a little tilted, the anti collision block will help to complete the closing action and hold the sliding glass. If guide rail is tilted severely, you may need to re-drill.

Shower door leaking issues:

Q1: Water leaks in the middle of the two doors, how should I do?

A1: Please swap all the two wide door seals to the middle, so that the middle will not leak.

Q2: The bottom of the inner door leaks, how should | do?

A2: Please confirm product wall bracket punching data are correct and the anti-splash threshold glue seals well without leaking, then following adjustment steps need to be made. 1. Adjust the angle of the shower head, avoid the shower water directly wash the bottom of the inner door. 2. Please swap the left and right position of the two doors. 3. After completing steps 1 and 2, if the bottom of the inner door is still leaking you can adjust the height of the top roller to reduce the height of the glass. Complete these 3 steps would solve it, if there still leak please contact customer service for support.

Please contact our customer service to confirm the return steps before returning or get order replacement.
Customer Service:
470-926-8618
321-946-6293

Installation Video:
https://youtu.be/EdaR3YgguuQ
www.mcocodsupport.com
Return Address:
4800 Little John St. Baldwin Park, A 91706
09 Dodd Blvd SE,STE 1, Rome, GA 30161
470-926-8618
321-946-6293

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>