FH4 Coil Units Residential Fan

Product Information

Specifications

• Models: FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4,
  PF4, FMA, F54, FY5

• Type: Residential Fan Coil Units

Introduction

The FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4,
FMA, F54, FY5 Residential Fan Coil Units are versatile and
efficient units designed for residential use. This product manual
provides detailed instructions on service and maintenance for
optimal performance and safety.

Fan Coil Description and Troubleshooting

The fan coil units include various models such as FY5, FH4, PF4
(even sizes), and FF1E (even sizes). The fan motor is a two or
three-speed direct drive motor. The high-speed lead is black, the
low-speed lead is red, and the common lead is yellow. It is
important to ensure that the proper blower speed has been selected
for optimal performance.

The motor is turned on through two different routes. The first
occurs when the thermostat calls for the fan in cooling, heat pump,
or fan-only mode. A 24VAC signal is sent to the relay, causing the
relay to close its normally open contacts and turning the fan
on.

InteliSenseTM Technology (FT4)

The FT4 model features InteliSenseTM Technology that enhances
the performance and efficiency of the fan coil unit. This
technology utilizes advanced sensors and algorithms to optimize the
operation of the unit based on environmental conditions and user
preferences. It provides a comfortable and energy-efficient indoor
environment.

Connected Portal and Service Tech App

The fan coil units are compatible with the Connected Portal and
Service Tech App. These tools allow service technicians to remotely
monitor and diagnose the unit, perform software updates, and access
troubleshooting guides. This ensures quick and efficient service
and maintenance.

Power On LED/Board States

The fan coil units are equipped with a Power On LED that
indicates the operational status of the unit. The LED and board
states provide valuable information for troubleshooting purposes.
Refer to the instruction manual for a detailed guide on
interpreting the LED and board states.

How to Troubleshoot

If you encounter any issues with the fan coil unit, refer to the
troubleshooting section of the instruction manual. It provides
step-by-step instructions to identify and resolve common problems.
If the issue persists, contact a qualified service technician for
further assistance.

How Does the Service Tech Know when the System is Functioning

Properly?

The service technician can determine if the system is
functioning properly by monitoring the unit’s performance
indicators and comparing them to the specified values.
Additionally, the Connected Portal and Service Tech App provide
real-time data and alerts, allowing the technician to assess the
system’s performance remotely.

Description of Electric Heater Components (FFM, FMA)

The FFM and FMA models include electric heater components for
supplemental heating. These components provide additional warmth
during colder periods. Refer to the instruction manual for detailed
information on the electric heater components and their
operation.

Product Usage Instructions

Safety Considerations

Before starting the installation or performing any maintenance
tasks, it is essential to read the entire instruction manual and
follow all safety considerations. The following safety precautions
should be followed:

• Wear safety glasses, protective clothing, and work gloves.

• Have a fire extinguisher available.

• Consult local building codes and the current editions of the
  National Electrical Code (NEC) NFPA 70.

• In Canada, refer to the current editions of the Canadian
  Electrical Code CSA C22.1.

Ensure that you recognize safety information by identifying the
safety-alert symbol. Whenever you see this symbol on the unit or in
instruction manuals, be alert to the potential for personal
injury.

Unit Operation and Safety Hazard

It is important to note the following warnings:

• Failure to follow this warning could result in personal injury
  or death.

• R-410A systems operate at higher pressures than R-22 systems.
  Do not use R-22 service equipment or components on R-410 equipment.
  Ensure service equipment is rated for R-410.

Electrical Operation Hazard

Take the following precautions to avoid electrical hazards:

• Always turn off all power to the unit before installing or
  servicing it.

• There may be more than one disconnect switch, so ensure that
  all power sources are turned off.

• If applicable, turn off accessory heater power.

• Lock out and tag the switch with a suitable warning label.

Frequently Asked Questions (FAQ)

Q: What should I do if I encounter an issue with my fan coil

unit?

A: If you encounter any issues with the fan coil unit, refer to
the troubleshooting section of the instruction manual. It provides
step-by-step instructions to identify and resolve common problems.
If the issue persists, contact a qualified service technician for
further assistance.

Q: How can I monitor the performance of my fan coil unit?

A: The fan coil units are equipped with a Power On LED that
indicates the operational status of the unit. Additionally, the
Connected Portal and Service Tech App provide real-time data and
alerts, allowing you to monitor the performance of your unit
remotely.

Q: Can I use R-22 service equipment on R-410A systems?

A: No, R-410A systems operate at higher pressures than R-22
systems. It is important to use service equipment and components
rated for R-410A to ensure safe and proper operation.

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5 Residential Fan Coil Units

Service and Maintenance Instructions

NOTE: Read the entire instruction manual before starting the installation.
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Fan Coil Description and Troubleshooting. . . . . . . . . . . . . . . . . . . . . 2
FY5, FH4, PF4 (even sizes) and FF1E (even sizes) . . . . . . . . . . . 2 Fan Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Electric Heater Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Cleaning or Replacing Refrigerant Flow-Control Device . . . . . 2 Sequence of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 CES013003-00, 01 (HK61EA002, HK61EA006) Control Boards3 Printed Circuit Board (PCB) Component . . . . . . . . . . . . . . . . . . 3 Unit Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Troubleshooting the Printed Circuit Board (CES013000-00, 01 / HK61EA002 / HK61EA006) . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
FB4C, FJ4, FX4D, F54, PF4, FF1E, and FZ (odd sizes). . . . . . . . 5 Fan Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
FV, FT4, FG4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Constant Air Flow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Integrated Controls and Motor ECM2.3/5.0 . . . . . . . . . . . . . . . . 7 PCB Layout and Description (FT4, FV4). . . . . . . . . . . . . . . . . . 7 Sequence of Operation (FT4, FV4) . . . . . . . . . . . . . . . . . . . . . . 7 Easy Select Configuration Taps . . . . . . . . . . . . . . . . . . . . . . . . 10 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
InteliSenseTM Technology (FT4) . . . . . . . . . . . . . . . . . . . . . . . . . 14 Connected Portal and Service Tech App . . . . . . . . . . . . . . . . . 14 Power On LED/Board States . . . . . . . . . . . . . . . . . . . . . . . . . . 14 How to Troubleshoot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 How Does the Service Tech Know when the System is Functioning Properly? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
FE4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Electronically Commutated Motor ECM 3.0 . . . . . . . . . . . . . . 15 Troubleshooting (FE4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Vefify Motor Winding Section . . . . . . . . . . . . . . . . . . . . . . . . . 16 Motor Turns Slowly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 SEQUENCE OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . . 18 ADVANCED TROUBLESHOOTING: . . . . . . . . . . . . . . . . . . 18 Filter Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Cooling Coil, Drain Pan, and Condensate Drain . . . . . . . . . . . 19
FFM and FMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Fan Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Time Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Electric Heater Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Cleaning or Replacing Refrigerant Flow-Control Device . . . . 21 Sequence of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Electric Heater Function and Troubleshooting . . . . . . . . . . . . . . . . . 25 FB4, FE4, FF1E, FH4, FJ4, FV4, FX4, FZ and PF4 . . . . . . . . . . 25 Description of Electric Heater Components . . . . . . . . . . . . . . . . 25 Limit Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 KFC and KFD Electric Heat Relay. . . . . . . . . . . . . . . . . . . . . . 25 Troubleshooting KFC and KFD Series Electric Heaters . . . . . . . 25 Discolored Wire Insulation at Terminal . . . . . . . . . . . . . . . . . . 25 Fuse Failure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 No Heat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Heater Will Not Turn Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Nuisance Trips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

FFM, FMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Description of Electric Heater Components . . . . . . . . . . . . . . . . 25
Limit Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Sequencer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 FB4, FE4, FE4A/B, FH4, FJ4, FT4, FV4, FX4, FZ4, F54 and PF426 Filter Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Cooling Coil, Drain Pan, and Condensate Drain . . . . . . . . . . . 26 Blower Motor and Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 FF1E, FFMA, FMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Cooling Coil, Drain Pan, and Condensate Drain . . . . . . . . . . . 27 Blower Motor and Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Refrigerant Flow-Control Devices. . . . . . . . . . . . . . . . . . . . . . . . 28 Thermostatic Expansion Valves (TXV) . . . . . . . . . . . . . . . . . . 28 Problems Affecting TXV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Aluminum Coil Unit TXV’s. . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Piston Body Cleaning and Replacement . . . . . . . . . . . . . . . . . . . 29 Liquid Tube Strainer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Aluminum Coil Repair. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Pre-Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Old Copper or Tin-Plated Coils with TXV. . . . . . . . . . . . . . . . 30 Old All- Aluminum Coils with TXV. . . . . . . . . . . . . . . . . . . . . 30 Installation ­ A-Coil Units Only. . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Installation ­ Slope Coil Units Only. . . . . . . . . . . . . . . . . . . . . . . . . 32
SAFETY CONSIDERATIONS
Improper installation, adjustment, alteration, service, maintenance, or use can cause explosion, fire, electrical shock, or other conditions which may cause death, personal injury or property damage. Consult a qualified installer, service agency, or your distributor or branch for information or assistance. The qualified installer or agency must use factory-authorized kits or accessories when modifying this product. Refer to the individual instructions packaged with kits or accessories when installing.
Follow all safety codes. Wear safety glasses, protective clothing and work gloves. Have a fire extinguisher available. Read these instructions thoroughly and follow all warnings or cautions included in literature and attached to the unit. Consult local building codes and the current editions of the National Electrical Code (NEC) NFPA 70.
In Canada, refer to the current editions of the Canadian Electrical Code CSA C22.1.
Recognize safety information. This is the safety-alert symbol . When you see this symbol on the unit and in instruction manuals, be alert to the potential for personal injury.
Understand the signal words DANGER, WARNING, and CAUTION. These words are used with the safety-alert symbol. DANGER identifies the most serious hazards which will result in severe personal injury or death. WARNING signifies hazards which could result in personal injury or death. CAUTION is used to identify unsafe practices which may result in minor personal injury or product and property damage. NOTE is used to highlight suggestions which will result in enhanced installation, reliability, or operation.

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

! WARNING
UNIT OPERATION AND SAFERTY HAZARD Failure to follow this warning could result in personal injury or death. R-410A systems operate at higher pressures than R-22 systems. Do not use R-22 service equipment or components on R-410 equipment. Ensure service equipment is rated for R-410.
! WARNING
PERSONAL INJURY AND PROPERTY DAMAGE HAZARD Failure to follow this warning could result in property damage, personal injury, or death. For continued performance, reliability, and safety, the only approved accessories and replacement parts are those specified by the equipment manufacturer. The use of non-manufacturer approved parts and accessories could invalidate the equipment limited warranty and result in fire risk, equipment malfunction, and failure. Please review manufacturer’s instructions and replacement part catalogs available from your equipment supplier.
! CAUTION
HOT TUBE WARNING Failure to follow this caution could result in personal injury and/or property damage. Refrigerant lines can reach or exceed 130 °F (54 °C). Avoid contact with the vapor header or vapor line, especially in Heating Mode. Do not service A2L refrigerant fan coils while these components are hot to avoid risk of ignition source.
INTRODUCTION
These fan coil units are designed for flexibility in a variety of applications that meet upflow, horizontal, or downflow requirements. Units are available in 1-1/2 through 5 ton nominal cooling capacities. Factory-authorized, field- installed electric heater packages are available in 3 through 30 kilowatts. FMA4X, FMA4P Fan Coils are designed with application flexibility in mind and are suitable for closet and flush mount installations. Units are available with field-installed electric heat with circuit breaker. Units are used indoors as the fan coil for split-system heat pumps or air conditioners. The FMA4P uses a refrigerant piston metering device and a 3 speed PSC Motor. FMA4X uses a TXV and a 5 speed multi-tap ECM Motor for efficiency. Units are available in 18,000 through 36,000 Btuh nominal cooling capacities. NOTE: Nuisance sweating may occur if the unit is installed in a humid location with low airflow. Units are designed for upflow application only. Local codes may linit this free-air-return type unit to installation in single-level applications.
! WARNING
ELECTRICAL OPERATION HAZARD Failure to follow this warning could result in personal injury or death. Before installing or servicing unit, always turn off all power to unit. There may be more than one disconnect switch. Turn off accessory heater power if applicable. Lock out and tag switch with a suitable warning label.

Fan Coil Description and Troubleshooting FY5, FH4, PF4 (even sizes) and FF1E (even sizes)
Fan Motor The motor is two or three speed direct drive. High-speed lead is black, low-speed lead is red, and common lead is yellow. Be sure proper blower speed has been selected.
The motor is turned on through two different routes. The first occurs when thermostat calls for the fan in cooling, heat pump, or fan-only mode. A 24VAC signal is sent to relay, causing relay to close its normally open contacts, turning fan on.
The second occurs when there is a call for electric heat. A 24VAC signal is sent to heater sequencer/relay, causing it to close, directing 230V through the normally closed contact of fan relay, turning fan on. The fan remains on until sequencer/relay opens.
If motor does run, test motor for an open winding or a winding shorted to motor case. If either is present, replace motor.
Electric Heater Service Service can be completed with heater in place. Shut off power before servicing.
Limit Switch
Refer to the (Electric Heater Function and Troubleshooting on p25) section of this manual.
Sequencer
Refer to the (Electric Heater Function and Troubleshooting on p25) section of this manual.
Transformer
A 40-VA transformer supplies 24V power for control circuit. Check for 208/230V on primary side of transformer. If present, check for 24V on secondary side.
NOTE: Transformer is fused. Do not short circuit.
Fan Relay
Relay coil is 24V. Check for proper control voltage. Replace relay if faulty.
Cleaning or Replacing Refrigerant Flow-Control Device Refer to Fig. 29 and instructions given in (Piston Body Cleaning and Replacement on p29).
The refrigerant flow-control device is protected by a wire mesh strainer. It is located inside the 3/8-in. liquid tube at field braze joint next to flow- control device. Access to strainer is through field braze joint.
Sequence of Operation Condensing Unit
COOLING–When thermostat calls for cooling, the circuit between R and G is complete and single-pole single-throw relay FR is energized. The normally open contacts close causing blower to operate.
The circuit between R and Y is also complete. This completed circuit causes contactor in outdoor unit to close which starts compressor and outdoor fan.
HEATING–When thermostat calls for heating and FAN switch is set on AUTO, the circuit between R and W is complete. The heater sequence SEQ is energized which closes contacts of relay. There will be a time delay. This completed circuit energizes all heating elements HTR and blower motor.
Heat Pump
COOLING–On a call for cooling, the thermostat makes circuits R-O, R-Y, and R-G. Circuit R-O energizes reversing valve, switching it to cooling position. Circuit R-Y energizes contactor starting outdoor fan motor and compressor. Circuit R-G energizes indoor unit blower relay starting indoor blower motor.

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 2

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

When thermostat is satisfied, its contacts open de-energizing contactor reversing valve and blower relay. This stops compressor and fan motors.
HEATING–On a call for heating, the thermostat makes circuits R-Y and R-G. Circuit R-Y energizes contactor starting outdoor fan motor and compressor. Circuit R-G energizes indoor blower relay starting blower motor.
Should temperature continue to fall, R-W circuit is made through second-stage room thermostat bulb. Circuit R-W energizes a sequencer bringing on supplemental electric heat.
When thermostat is satisfied, its contacts open de-energizing contactor and sequencer. All heaters and motors should stop.
CES013003-00, 01 (HK61EA002, HK61EA006) Control Boards
This section examins the functional operation of the PCB components.
Printed Circuit Board (PCB) Component
Layout of the actual PCB is depicted in Fig. 2 and Fig. 1.
1. The low-voltage stripped leads are used to connect the 24V side of transformer to indoor thermostat and outdoor section.
2. A 5A fuse is used to protect the low-voltage transformer secondary.
3. The fan relay is controlled by thermostat and turns fan on and off.
4. A plug is used as the connection for PCB power and electric heaters. Note the pin numbers on plug.
5. A time-delay relay circuit keeps fan motor running for approximately 90 seconds after G is de-energized. The time-delay can be defeated by cutting jumper JW1.
Unit Functions
Transformer
1. Proper Wiring of Transformer Primary or High Side Yellow wire from Molex plug is wired to C terminal on transformer and black wire from PCB relay (normally-open) terminal is wired to 208V or 230V terminal on transformer. Units are factory wired at 230V terminal.
2. Proper Wiring of Transformer Secondary or 24V Side Red wire of transformer is wired to T terminal on PCB and brown wire of transformer is wired to C terminal on PCB.
NOTE: T terminal on PCB is used to protect the transformer. T terminal is connected through the fuse to R terminal on PCB.
Indoor Fan
1. Wiring Indoor fan motor yellow lead is wired to C terminal on transformer. The red, blue, or black speed lead is wired to SPT terminal on fan relay part of PCB. Units are factory wired on medium speed (blue lead connected).
NOTE: Unused fan speed leads must be capped or taped off to prevent direct short to cabinet surface.
2. Functional Control a. Thermostat and Relay Control When thermostat calls for the fan in cooling, heat pump, heating, or fan-only mode, a 24VAC signal is sent to relay. This causes the relay to close its normally-open contacts, turning on fan. When thermostat no longer calls for the fan, the signal sent to relay is turned off and relay opens causing fan to turn off after a 90-second fan-off delay. b. Sequencer/Electric Heat Relay Interlock The fan will also operate whenever there is a call for electric heat, even if fan relay is not energized. This happens because fan is interlocked with first stage of electric heat through the normally-closed contact of fan relay.
NOTE: The fan interlock is only connected to first stage electric heat (W2). W3 and E do not contain an interlock with fan. See outdoor thermostat installation instructions when electric heat staging is desired.

Electric Heat
When thermostat calls for electric heat, a 24VAC signal is sent to sequencer/heat relay through W2, causing first stage to turn on. W3 and E also receive signal if wired in with W2. If W3 and E are not wired to W2, the sequencers/heat relays can be controlled individually to stage additional electric heat. The sequence control is described in the following section:
1. W2 When thermostat sends a signal to W2, a 24VAC signal is applied across sequencer/relay No. 1, causing it to close. When sequencer/relay No. 1 closes, first stage of electric heat is energized. In straight electric heat, fan is also energized through the normally closed contacts of fan relay. In cooling, heat pump, or manual fan mode, fan will already be running since fan relay would have been energized. When thermostat stops calling for electric heat, the 24VAC signal to sequencer/relay No. 1 turns off and sequencer opens after a delay of 60 to 90 seconds. Heaters equipped with relays will be de-energized immediately. When sequencer/relay opens, first stage of heat turns off along with fan, providing thermostat is not calling for the fan.
2. W3 When a signal is sent to W3, a 24VAC signal to sequencer/relay No. 2 causes it to close, with second stage of electric heat turning on. The 24VAC signal applied to sequencer/relay No. 1 causes fan to operate. Timing is such that sequencer/relay No. 1 will turn on before sequencer/relay No. 2. When signal to W3 is turned off, sequencer/relay No. 2 opens. If W2 is also satisfied, first stage of electric heat and fan will also turn off, providing thermostat is not calling for the fan.
3. E When thermostat sends a signal to E, a 24VAC signal is sent to sequencer/relay No. 3. The 24VAC signal applied to sequencer/relay No. 3 turns on third stage of electric heat. The 24VAC signal applied to sequencer/relay No. 1 turns on first stage of electric heat and fan. When thermostat stops calling for electric heat, the signal to sequencers/relays 1, 2, and 3 are turned off, and sequencers/relays open. This causes electric heat to turn off with fan, providing thermostat is not calling for the fan.
NOTE: Electric heaters are factory wired with all stages tied together. If independent staging is desired, consult outdoor thermostat installation instructions, or corporate thermostat instructions.
Troubleshooting the Printed Circuit Board (CES013000-00, 01 / HK61EA002 / HK61EA006)
Use wiring schematics shown in Fig. 2, and Fig. 1 as a guide in troubleshooting PCB unless otherwise noted.
If Fan Will Not Turn On from Thermostat: · IF THERE IS NO HIGH VOLTAGE TO TRANSFORMER: (1.) Check plug/receptacle connection. This supplies power from heaters to PCB Fan Relay. Be sure plug is connected properly. (2.) Check sequencer/relay No. 1 and plug wiring. Yellow wire should be connected to Pin No. 9 of plug and to limit switch. Black wire should be connected to Pin No. 7 of plug and to sequencer/relay No. 1. (3.) Check field power leads L1 and L2. If these are not receiving power, system cannot function. · IF TRANSFORMER HAS HIGH VOLTAGE APPLIED TO IT: (1.) Check low-voltage transformer leads R (red) and C (brown). Be sure they are wired to correct locations. (2.) Check output voltage of transformer secondary side R (red) and C (brown). Be sure transformer output is between 18VAC and 30VAC. If transformer output is incorrect and transformer is receiving correct input voltage (208V or 230V), then transformer needs to be replaced with

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 3

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

recommended transformer. If no problem exists with transformer secondary, proceed to items 3 and 4. (3.) Check low-voltage fuse shown in Fig. 2 or Fig.

1. If fuse is blown, replace it with an identical 5A fuse. The transformer cannot supply power to board with fuse blown or loose. If fuse blows when unit has power applied to it, the system most likely has one of the following problems: · Check all 24V wiring for an electrical short. · The maximum load on transformer is 40VA. If load on
   transformer is excessive, the low-voltage 5A fuse will blow to protect transformer. If load exceeds VA rating of transformer, a larger VA rated transformer needs to be installed. Check sequencers/relays for excessive current draw. · Check wiring of heaters. If a heater is miswired, fuse may blow. If a heater is miswired, correct miswiring by comparing it to heater wiring label. (4.) Check connections on primary side of transformer. If they are not connected properly, the transformer secondary cannot supply the 24V signal to energize fan relay. If transformer is receiving correct primary voltage but is not putting out correct secondary voltage, transformer needs to be replaced.
   If Electric Heat Stages Will Not Turn On But Fan Will Turn On: · IF THERE IS NO HIGH VOLTAGE TO TRANSFORMER: (1.) Check plug connection between heaters and board. This supplies power to transformer and fan. Be sure plug is connected properly. (1.) Check sequencer/relay No. 1 and plug wiring. Yellow wire should be connected to Pin No. 9 of plug and to limit switch. Black wire should be connected to Pin No. 7 of plug and to sequencer/relay No. 1. (1.) Check incoming high-voltage power leads. If these are not receiving power, system cannot function. · IF TRANSFORMER HAS VOLTAGE APPLIED TO IT: (1.) Check low- voltage transformer leads R (red) and C (brown). Make sure they are wired to correct location. The unit will not function without proper connections. (1.) Check output voltage of transformer secondary side R (red) and C (brown). If transformer output is low (less than 18VAC), refer to items 3 and 4 of previous “IF TRANSFORMER HAS HIGH VOLTAGE APPLIED TO IT” section. · IF TRACES ARE OVERHEATED ON BACK OF PCB: Usually whenever a trace is blown on PCB, it means either there has been a high-voltage short or high voltage has been applied to low-voltage circuit. This can be prevented by making sure PCB is wired correctly before PCB has power applied to it. · If Transformer Fuse Keeps Blowing: When low-voltage fuse blows, it means transformer would have blown if fuse had not been in circuit to protect it. The fuse usually blows when there is a high current draw on transformer, high voltage applied to low- voltage circuit, or a direct secondary short. When there is a high current draw on transformer, it is most likely because transformer has been shorted or system is trying to draw more VA than transformer rating allows. When fuse blows because of high voltage, the system has mixed high- and low-voltage signals. (1.) Check wiring of sequencers/relays as shown in Fig. 2 and Fig. 1. Be sure transformer is not shorting out because thermostat wires are miswired. (1.) Check wiring of relays as shown in Fig. 2 and Fig. 1. Be sure low-voltage and high-voltage wiring is correct. (1.) Check VA draw on transformer. If VA draw is more than VA rating of transformer, fuse will blow. If this is the case,

replace transformer with one that has a higher VA rating and meets system specifications.
If Fan Runs Continuously: (1.) If PCB has no low-voltage power, check blue and black fan leads. These may be switched at sequencer/relay. (1.) If PCB has low-voltage power, check fan relay to see if it is opening and closing. It may be stuck in the normally closed position due to debris in relay.
Transformer Failure: Check 208V and 230V transformer connections. They may be miswired.

C8

5 AMP
JW1

SPT FAN
RELAY

® U1
K1 ® HSCI

C7
R2 R3 C3 R6
R11 Z1 R1

R10 R9 R7
C4
C6

R8

C5

C C C T G R
F1
NC

C2

C1 R5

NO

R4

Q1 D2

D1

LR40061
Fig. 1 ­ Fan Coil Printed Circuit Board (HK61EA006) A03010

CPC-E 94V-0

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 4

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

CESO130003-01

1005-161

1005-83-161A

C7
R2 R3 C3 R6 R11
Z1 R1 C2
D2
D1

® U1

C8
R10 R9 R7
C4
C6

R8

C5

C1 R5 R4
Q1

LR40061

K1 ® HSCI

RG T C 5 AMP
JW1

C T G R
F1 NC NO
FAN RELAY

SPT FAN
RELAY

LOW VOLTAGE FUSE

PCB BLOCK WIRING

NO

NC

TIME

DELAY SPT

FUSE

G

R

T

C

Fig. 2 ­ Fan Coil Printed Circuit Board (CES013003-00, 01 / HK61EA002)

CPC-E 94V-0

312753 T-O-D 60TX11
HH19ZA945 C9725
L145-55F 312753 T-O-D 60TX11 HH19ZA945 C9725 L145-55F

NC NO

5
SPT
FAN RELAY

A97020
WARNING
ELECTRIC SHOCK HAZARD
DISCONNECT REMOTE POWER SUPPLY BEFORE OPENING PANEL.
PULL TO OPEN
322861-101 REV. A

FF1E CONTROL BOX

Fig. 3 ­ Electric Heater Control Box

A13032

FB4C, FJ4, FX4D, F54, PF4, FF1E, and FZ (odd sizes)
Fan Motor
The multi-speed ECM motor used with this product contains two parts: the control module and the motor winding section. Do not assume the motor or module is defective if it will not start. Go through the steps described below before replacing control module or entire motor. The control module is available as a replacement part.
1. It is normal for the motor to rock back and forth on startup. Do not replace the motor if this is the only problem identified. (1.) If the motor is not running: · Check for proper high voltage and ground at the L,G, and N connections at the motor. Correct any voltage issue before proceeding to the next step. · The motor is communicated through 24VAC signals to the 1, 2, 3, 4, 5 and C (common) terminals. Not all taps are programmed, if low voltage is applied to an non-programmed terminal, the motor will not operate, which is normal. Verify the part number of the motor matches the correct replacement motor part number for the unit model number. · Initiate a demand from the thermostat and check the voltage between C (common) and terminal 1- 5. If voltage is present and the motor isn’t operating, then the motor/control module is failed. (2.) Prior to installing the replacement control module, the motor section condition needs to be verified. · Check to see if the blower wheel spins freely. · To check for short to ground, use an ohmmeter to measure the resistance from any one of the motor connector pins to the aluminum end plate of the motor. This resistance should be greater than 100,000 ohms.

· Check the motor phase-to-phase resistance between each of the leads in the three-pin motor connector. The lead-to-lead resistance across any two leads should be less than 20 ohms. Each lead-to-lead resistance should be the same within ± 10 percent.
· If any motor fails any of the three tests, do not install a new control module. The new control can fail if placed on a defective motor.
The prior fan coil models with multi-speed ECM blower motors used a printed circuit board, similar to the PSC models. The current fan coils do not use the printed circuit board and rely on the motor control programming to provide the off-delay timing.
Another design aspect of the control board was to provide a resistor in the “G” circuit in case a power stealing thermostat was used. This resistor is no part of the wiring harness, as shown on wiring diagram. The resistor is a 2W, 1500-ohm resistor.
If the resistor has failed open, a likely cause is due to the power stealing thermostat. Connecting C (common) may resolve the issue. Having an open resistor should not affect the operation of the motor.
Fan Speed Selection
The fan speed selection is done at the motor connector. Units with or without electric heaters require a minimum CFM. Refer to the unit wiring label to ensure that the fan speed selected is not lower than the minimum fan speed indicated.
To change motor speeds disconnect the BLUE fan lead from motor connector terminal No. 2 (factory default position) and move to desired speed-tap; 1, 2, 3, or 5.
Speed-taps 1, 2, and 3 have a 90-second blower off time delay pre-programmed into the motor. Speed-tap 4 is used for electric heat only (with 0 second blower time delay) and the WHITE wire should remain on tap 4. Speed-tap 5 is used for high static applications, but has

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 5

NAMEPLATE LABEL

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

a 0-second blower time delay pre-programmed into the motor. See Airflow Performance tables for actual CFM. Also, see Fig. 4 for motor speed selection location.
NOTE: In low static applications, lower motor speed tap should be used to reduce possibility of water being blown off coil.

Tap 1

Low

90 sec off delay

Tap 2

Medium

90 sec off delay

Tap 3

High

90 sec off delay

Tap 4

Electric heat

0 sec off delay

Tap 5

Max

0 sec off delay

electric heat airflow is same CFM as Tap 3, except 0 sec off delay high static applications, see airflow tables for max airflow

1 2 3 4 5

Speed Taps may be located on motor, or on plug close to motor.
1 2 3 4 5

Fig. 5 ­ FV4 Motor / ECM5.0 Motor (pre-2023)

A13028

OPTIONAL SAFETY GROUND DRAIN HOLE

12345 POWER CONNECTOR

OPTIONAL SAFETY GROUND

DRAIN HOLE

9 10 11 12 13 14 15 16 12345678
CONTROL CONNECTOR

CONTROL POWER

C LG N

Fig. 4 ­ Motor Speed Selection for FB4C, FJ4, FX4D, FZ4A, F5A411&048 PF4 (odd sizes)

ENDSHIELD DRAIN HOLE
Fig. 6 ­ FV4 Motor / ECM2.3 Motor (pre-2023)

A98201

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 6

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

Fig. 7 ­ ECM Motor, post-2023

A230463

FV, FT4, FG4
Constant Air Flow
Unlike fan coils using induction motors where static pressure affects airflow, these fan coils are constant airflow units. The blower delivers requested airflow regardless of static pressure. Consult fan coil Product Data for static pressure limits. The ECM2.3/5.0 is pre-programmed and contains airflow tables for all modes of operation. Blower characteristics (requested airflow, torque, and speed) are known from laboratory testing If any two characteristics are known, the third is defined.
Requested airflow is known from Easy Select board configuration and thermostat signals. Torque is known because it is directly related to stator current, which is measured by motor control. Speed is measured by counting back EMF pulses from stator windings. This information is entered into an expression that calculates torque from speed and airflow numbers. If calculation does not match stored blower characteristics, torque is adjusted until agreement is reached. This calculation and adjustment is performed every 0.8 seconds while motor is in operation. There is no direct measure of static pressure, but unit does react to a change in static to maintain constant airflow. A change in pressure will result in a change in stator speed and torque. The motor will begin to adjust on the next sampling, calculate new desired speed and torque, and adjust as necessary.
Integrated Controls and Motor ECM2.3/5.0
An ECM2.3/5.0 is fed high voltage AC power through the 5-pin connector (Fig. 6 or Fig. 5). The AC power is then internally rectified to DC by a diode module. After rectification, DC signal is electronically communicated and fed in sequential order to three stator windings. The frequency of these commutation pulses determines motor speed. The rotor is permanently magnetized.
An ECM2.3/5.0 is powered with high voltage at all times. The motor will not run with high voltage alone. Low voltage must be applied to control plug to run motor.
ECM2.3/5.0 Control Power
The ECM2.3/5.0 control power is supplied from R circuit through printed circuit runs to motor control Connector-Pin 8, through motor control harness to motor. The C side of low-voltage control power circuit is connected by printed circuit runs to motor Connector pins 9, 10, and 11, then through motor control harness to motor.

Low-Voltage Circuit Fusing and Reference
The low-voltage circuit is fused by a board-mounted 5A automotive-type fuse placed in series with transformer SEC2 and R circuit. The C circuit of transformer is referenced to chassis ground through a printed circuit run at SEC1 connected to metal standoff marked.
For FT: The low-voltage circuit is fused by a board-mounted 5A
automotive fuse placed in series with the transformer SEC1 (24VAC)
and the R circuit. The C circuit of the transformer is referenced to
chassis ground through a printed circuit run at SEC2 (COM) connected
to metal standoff marked with ground symbol.
NOTE: The PCB must be mounted with two screws and motor ground lead secured to blower housing or erratic motor operation can result.
Transformer, Motor, and Electric Heater Power Connection
Transformer high voltage supplied from electric heater package or high voltage leads through 12-pin heater connector plug/recp2. The ECM2.3/5.0 power connections are made at the transformer primary terminals. The transformer secondary connections are made at SEC1 and SEC2 connectors.
PCB Layout and Description (FT4, FV4) NOTE: Layout of actual PCB is depicted in Fig. 8.
The Easy Select Board is the interface between the ECM motor and other system components. The board offers choices of electric heater size, outdoor unit size and type, comfort or efficiency settings, on and off delay profiles, and continuous fan speed. The installer should select the correct size of components that are being installed in each installation. If no selections are made, the factory default settings are for the largest heater, largest outdoor unit, AC system type, nominal airflow adjust, and 0/90 time delay.
A 16×4 motor signal translator is present for the translation of data from the board to the motors and is mounted on the back of the PCB bracket.
NOTE: Outdoor unit model should have an AHRI rating with the variable speed fan coil. Some outdoor unit models will not work properly with this fan coil. · Power for system is supplied from a 230VAC, 60-Hz line. Class 2
voltage (24VAC nom.), used for thermostat connections, is derived from transformer located in close proximity to PCB. ­ The 24VAC secondary circuit includes 5A automotive type fuse. · Connection to heater panel is made through 12-pin connector PL-1. Connections to thermostat are made at screw terminals. Twenty-one pin terminals comprise field select taps for motor. · Fuse Data: 5A automotive-type ATC/ATO (tan) · 32V · 200 percent current opening time of five seconds maximum
Electrical Connections
Twenty-one 0.110-in pin terminals are used to provide programming selections for operating modes of ECM2.3/5.0. The selection modes are listed below. For additional information, refer to Easy Select Configuration Taps section. · AUX Heat Range–(Violet Wire) · AC/HP Size–(Blue Wire) Type–(Orange Wire) · AC/HP CFM Adjust–(Black Wire) · AC/HP Time Delay–(Grey Wire) · Continuous Fan–(Yellow Wire)
Sequence of Operation (FT4, FV4) Continuous Fan Mode
The thermostat closes circuit R to G. The unit delivers the airflow selected for fan only operation.

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 7

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

Cooling Mode–Single Speed or Two-Speed High
Thermostat closes circuits R to G, R to Y/Y2 and R to O (heat pump only). A circuit R to Y1 is required for two-speed high operation. Airflow delivered the airflow selected by AC/HP SIZE selection and CFM ADJUST selection.
Cooling Mode–Two-Speed Low
Thermostat closes R to G and R to Y1 and R to O (heat pump only). Unit delivers two-speed low airflow for AC/HP SIZE and CFM ADJUST selected.
Cooling + Dehumidify Mode (Thermidistat or Comfort Zone II-B and Single-Speed Outdoor Unit Installed)
J1 jumper must be pulled from Easy Select Board. Control closes R to G, R to Y/Y2, and R to O (heat pump only) and open R to DH.

Dehumidification is active when 24VAC is removed from DH terminal. Unit delivers 20 percent less airflow.
SuperDehumidify Mode (Thermidistat or Comfort Zone II-B indoor control, Single-Speed Outdoor Unit)
This mode is only activated by the indoor control when COOL to DEHUMIDIFY and SUPERDEHUMIDIFY are configured at the control and there is a call for dehumidfication without a call for cooling. The control closes R to Y/Y2, R to O (heat pump only) and opens R to DH and R to G. This signals the fan coil to run at minimum airflow for maximum humidity removal. The control will cycle the equipment 10 minutes on and 10 minutes off until satisfied.
NOTE: Super Dehumidification and Thermidistat functionality is not available with certain thermostat models. Verify with the thermostat manufacturer if this functionality is critical to the application.

Table 1 ­ Motor and Modules

Model Size

Motor Type

Current Blower Motor P/N

Required Control Module Replacement Kit Number

FV4B_002

ECM2.3

HD44AE131

RMOD44AE131

FV4B_003

ECM2.3

HD44AE132

RMOD44AE132

FV4B_005

ECM2.3

HD44AE133

RMOD44AE133

FV4B_006

ECM2.3

HD46AE244

RMOD46AE244

FV4C_002 (Series A)

ECM2.3

HD44AR131

RMOD44AR131

FV4C_003 (Series A)

ECM2.3

HD44AR132

RMOD44AR132

FV4C_005 (Series A)

ECM2.3

HD44AR133

RMOD44AR133

FV4C_006 (Series A)

ECM2.3

HD46AR244

RMOD46AR244

FV4C_002 (Series B)

ECM5.0

HD44AR120

HK44ER120

FV4C_003 (Series B)

ECM5.0

HD44AR121

HK44ER121

FV4C_005 (Series B)

ECM5.0

HD44AR122

HK44ER122

FV4C_006 (Series B)

ECM5.0

HD46AR223

HK46ER223

Configuration Singular Singular Singular Modular Modular Modular Singular Singular Singular Modular Singular Singular Singular Modular Modular Modular

Table 2 ­ Motor and Modules ­ post-2023 (Mid and Deluxe Tier)

Fan Coil P/N FT4BNXB24 FT4BNXC36 FT4BNXC48 FT4BNBC36 FT4BNBC48 FT4BNBD60

Motor Type ECM ECM ECM ECM ECM ECM

Motor P/N HD44RM600 HD44RM600 HD46RM600 HD44RM600 HD46RM600 HD46RM600

Motor Signal Translator P/N
HK43EJ001 HK43EJ002 HK43EJ003 HK43EJ002 HK43EJ003 HK43EJ004

FG4ANXB24

ECM

HD44RM600

HK43EJ001

FG4ANXC36

ECM

HD44RM600

HK43EJ002

FG4ANXC48

ECM

HD46RM600

HK43EJ003

FG4ANBD60

ECM

HD46RM600

HK43EJ004

FE4BNXB24

ECM

HD44RM600

n/a

FE4BNXC36

ECM

HD44RM600

n/a

FE4BNXC48

ECM

HD46RM600

n/a

FE4BNBC36

ECM

HD44RM600

n/a

FE4BNBC48

ECM

HD46RM600

n/a

FE4BNBD60

ECM

HD46RM600

n/a

Control Module P/N HK38EA060 HK38EA060 HK38EA060 HK38EA060 HK38EA060 HK38EA060 HK61EA024 HK61EA024 HK61EA024 HK61EA024 HK38EA061 HK38EA061 HK38EA061 HK38EA061 HK38EA061 HK38EA061

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 8

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

5 F1
STI

®
SEC1

SEC2

5 AMP.

YYWWX

MAX. J1

DH

®

EASY SELECT

AUX/HEAT KW/CFM

R

0-30 0-20 0-10 0-5

1075 875 725 625

J2

W1

VIO

AC/HP SIZE

W2

036 030 024 018

BLU

ORN

SYSTEM TYPE AC HP-COMFORT HP-EFF
AC/HP CFM ADJUST

NOM

LO

HI

BLK

WHT

ON/OFF DELAY

0

30

90 90

0 ENH 0

CONTINUOUS FAN LO MED HI YEL

YEL

D2

D5

D4

R1 D3

D1 R2

Y1 Y/Y2 G O
C
AUX1 HUM1 AUX2 HUM2

HK61EA006

PL1 HEATER/MOTOR

24VAC
1 GRY

Fig. 8 ­ Easy Select Board

A13029

(for non-Limitless models; see Table 1 and Table 2 for P/N)

Fig. 9 ­ Detail of Limitless Printed-Circuit Board A95275B (FT4B only; see Table 2 for P/Ns) and Table 5 for Adjustments

SYSTEM DIAGRAM

HEATER/MOTOR

SEC1 SEC2

1/4″ 1/4″
12 11 10 9 8 7 6 5 4 3 2 1

AUX1 1/4″ HUM1 1/4″
AUX2 1/4″ HUM2 1/4″ GRY 1/4″

DIODE LOGIC

5 AMP

DH J1
R
W1 J2
W2
Y1
Y/Y2
G
O
C

AUX HEAT KW/CFM

AC/HP SIZE

SYSTEM AC/HP CFM ON/OFF CONTINUOUS

TYPE ADJUST

DELAY

FAN

NOTE: On FT4, SEC1 and SEC2 are reversed in the above image. See (Low-Voltage Circuit

Fusing and Reference on p7)

Fig. 10 ­ Easy Select Board Schematic

A96431

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 9

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

Type Connection Heater Connection

Table 3 ­ Connections and Connectors (FK4, FV4)

Type Connector

Pin No.

Description

Pin 1

Common to screw terminal G

Pin 2

Common to screw terminal Y/Y2 through diode D3

Pin 3

Common through Y1 through diode D2

Pin 4

Common to W2 screw terminal

Pin 5

Common to W2 screw terminal

12-Pin

Pin 6 Pin 7

Common to W1 screw terminal Common to W1 screw terminal

Pin 8

R 24Vac

Pin 9

Common to transformer C

Pin 10

Common to transformer C

Pin 11

Common to transformer C

Pin 12

Common to DH screw terminal

Table 4 ­ Typical Operating Modes

Operating Mode

Terminals Energized

Heat Pump Only Heating

R, Y/Y2, G, DH

Heat Pump Only Heating + Super Comfort Heat Mode

R, Y/Y2, DH

Heat Pump Heating + Auxiliary Heat (non-staged)

R, Y/Y2, G, DH, W2

Cooling

R, Y/Y2, G, DH, O

Cooling + Dehumidification

R, Y/Y2, G, O

Heat Pump Heating Mode — Single Speed or Two-Speed High
Thermostat closes R to Y/Y2 and R to G. A circuit R to Y1 is required for two- speed high operation. The unit delivers airflow selected by AC/HP SIZE selection and CFM ADJUST selection. Selected delay profile is active in this mode.
Heat Pump Heating Mode — 2-Speed Low
Thermostat closes R to G and R to Y1. Unit delivers two-speed low airflow for AC/HP SIZE and CFM ADJUST selected. Selected delay profile is active in this mode.
Non-Staged Auxiliary with Heat Pump Heating Mode
Thermostat should already have closed R to G, R to Y2 for heat pump heating operation. With J2 jumper in place, energizing either W1 or W2 will produce the W2 airflow. This is the greater of heat pump heating and auxiliary heat airflow plus an additional 15 percent. The elected delay profile is not active in this mode.
Staged Auxiliary Heat with Heat Pump Heating Mode
The auxiliary heat can be staged by removing the J2 jumper that ties W1 and W2 terminals together. Staging can be done by using outdoor thermostats or by using the Intelligent Heat Staging option where the indoor control can be configured for three-stage electric heat. The unit will automatically adjust airflow when the different stages of heat are energized. The airflow delivered will depend on the heat pump size selected and electric heat size selected. The greater of the two airflows will be delivered. The selected delay profile is not active in this mode.
Electric Heat without Heat Pump
Thermostat closes R to W and thermostat should be set up to energize G with W. This is due to the Super Comfort Heat programming in the motor. Energizing W without G will result in 25% lower airflow delivery. The selected delay profile is not active in this mode.

Super Comfort Heat Mode
This is a special heating mode only available on FV4 fan coils combined with a Thermidistat Control or Comfort Zone II-B. When this option is selected, the indoor control will monitor the outdoor temperature. The control will drop the G signal to the fan coil when the outdoor temperature is between 10° and 40° F. This triggers the motor to slow to approximately 213 CFM per ton. The heaters will stage as needed during this mode and the motor will adjust airflow as required. Below 10° F, the W1 control output will automatically energize on a call for heat. The ECM2.3/5.0 power connections are made at the transformer primary terminals. The transformer secondary connections are made at SEC1 and SEC2 connectors.
Easy Select Configuration Taps
The Easy Select taps are used by installer to configure system. The ECM2.3/5.0 uses selected taps to modify its operation to a pre-programmed table of airflows. Airflows are based on system size and mode of operation and those airflows are modified in response to other inputs such as the need for de- humidification (Fig. 8).
The FV4 and FT4 Fan Coils must be configured to operate properly with system components with which it is installed. To successfully configure a basic system (see information printed on circuit board located next to select pins), move the six select wires to pins which match components used, along with homeowner preferences.
Auxiliary Heat Range
The installer must select the auxiliary heat airflow approved for application with kW size heater installed. Each select pin is marked with a range of heaters for which airflow (also marked) is approved. For increased comfort select the narrowest kW range matching the heater size, for example, 0-10 for a 10-kW heater. This airflow must be greater than the minimum CFM for electric heater application with the size system installed for safe and continuous operation. Note that airflow marked is the airflow which will be supplied in emergency heat mode

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 10

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

and heating mode on air conditioners when electric heat is primary heating source. To ensure safe heater operation in heat-pump heating mode, when electric heaters are energized, the ECM2.3/5.0 will run the higher of heat pump airflow and electric heater airflow. The factory default selection is largest heater range approved (Fig. 8).
AC/HP Size
The factory default setting for air conditioner or heat pump size is largest unit meant for application with model of fan coil purchased. The installer needs to select air conditioner or heat pump size to ensure that airflow delivered falls within proper range for size of unit installed in all operational modes (Fig. 8).
The letters A, B, C, D may be marked on the silk screen. In that case, use the unit’s installation instructions to determine the Aux heat and AC/HP size. See Fig. 9.
Table 5 ­ Airflow Adjustment Table

Unit Size VIO

AUX Heat Range (kW/CFM)

A

B

C

D

24

0-20 / 1200 0-15 / 1050 0-10 / 750 0-5 / 700

36

0-20 / 1225 0-15 / 1050 0-10 / 750 0-5 / 700

48

0-30 / 1500 0-20 / 1350 0-15 / 1200 0-10 / 1000

60

0-30 / 1750 0-20 / 1350 0-15 / 1250 0-10 / 1200

AC/HP Size

BLU

A

B

C

D

24

036

030

024

018

36

042

036

030

024

48

048

042

036

030

60

060

048

042

036

Unpack unit and move to final location. Remove carton taking care not to damage unit. Inspect equipment for damage prior to installation. File claim with shipping company if shipment is damaged or incomplete.
Locate unit rating plate which contains proper installation information. Check rating plate to be sure unit matches job specifications.
System Type
The type of system must be selected.
1. AC–air conditioner (approx. 350 CFM/ton)
2. HP-COMFORT–provides lower airflow than air conditioner selection (approximately 315 CFM/ton) in heating mode. In cooling mode supplies 350 CFM/ton.
3. HP-EFF–provides same airflow for heat pump heating and cooling modes (approximately 350 CFM/ton).
The factory setting is AC (Fig. 8).
AC/HP CFM Adjust
Select low, nominal, or high airflow. The factory selection is NOM. The adjust selections HI/LO will regulate airflow supplied for cooling and heat pump heating modes only, +15 percent and -10 percent respectively. The adjust selection options are provided to adjust airflow supplied to meet individual installation needs for such things as noise, comfort, and humidity removal (Fig. 8).
ON/OFF Delay
NOTE: ON/OFF Delay is active only in cooling and heat pump only heating modes. In auxiliary heat mode or emergency heat mode, the ON delay is 0 seconds and the OFF delay is fixed and cannot be overridden.
Select desired time delay profile. Four motor-operation delay profiles are provided to customize and enhance system operation (Fig. 8). The selection options are:
1. The standard 90-seconds OFF delay (factory setting 0/90).

2. No delay option used for servicing unit or when a thermostat is utilized to perform delay functions (0/0).
3. A 30­seconds ON / 90­seconds OFF delay profile is used when it is desirable to allow system coils time to heat up/cool down prior to airflow. This profile will minimize cold blow in heat pump operation and could enhance system efficiency (30/90).
4. ENH, enhanced selection provides a 30­seconds ON / 150­seconds at 70 percent airflow and no OFF delay.
Continuous Fan
Select desired continuous-fan profile LO, MED, or HI. Airflow are provided to customize and enhance the continuous fan functions (Fig. 8). The possible selections are:
1. LO ­ provides 50 percent of Y/Y2 Cool airflow.
2. MED ­ provides 80 percent of Y/Y2 Cool airflow.
3. HI ­ provides 100 percent of Y/Y2 Cool airflow.
The factory setting is LO.
NOTE: If applied to two-speed unit, do not select continuous fan as HI since low speed cooling will also run at HIGH airflow and insufficient dehumidification may result.
Easy Select Board Jumpers
J1 ­ This jumper must be pulled to activate dehumidification mode. The jumper connects R to DH. With the jumper in, the DH terminal is always energized. With the jumper pulled, the DH terminal is de-energized. A control such as the Thermidistat must be used to supply the 24V signal when there is no call for dehumidification, and turn off the 24V when there is a call for dehumidfication.
J2 ­ This jumper activates heat staging. The jumper connects the W1 and W2 terminals together. If either is energized, W2 airflow is delivered. With the jumper pulled, there are separate airflows for W1 and W2.
J4 ­ This jumper is for InteliSenseTM operation (FT4B). As shipped, Y1 is connected to Y/Y2 by a field-removable jumper J4. With the jumper in place, in single stage operation InteliSenseTM communication is enabled. For 2-stage application, remove jumper J4.
Airflow Delivery
These units deliver airflow depending on the system size selections and operating mode. The thermostat energizes a combination of terminals on the Easy Select Board which tells the motor what CFM to deliver. The following are typical operating modes and the terminals that should be energized on the Easy Select Board.
NOTE: The DH terminal on the Easy Select Board is for dehumidification. It is de-energized on a call for dehumidification.
Variable Speed Motor Logic Sequence:
The ECM motors in these fan coils are programmed to deliver a variety of airflows. The motor goes through:
COOLING ­ The nominal cooling airflow for these fan coils is 350 CFM per ton. Selecting the HI adjust tap increases the airflow to 400 CFM per ton. The LO tap decreases airflow to 315 CFM per ton. The low adjustment is only active during normal cooling mode. Removing the signal from the DH terminal reduces the airflow to 80 percent of cooling airflow. Removing the G signal for Superdehumidify reduces the airflow to 50 percent of cooling.
HEATING ­ The base heat pump only heating airflow is determined by the SYSTEM TYPE selection on the Easy Select Board. If HP-EFFICIENCY is selected, the airflow is the same as Cooling. IF HP-COMFORT is selected, the airflow is 315 CFM per ton. The airflow will adjust up if necessary when auxiliary heating is required. When both the Y/Y2 and W1 or W2 terminals are energized, the motor will run the higher of the heat pump or electric heat airflows. During Super Comfort Heat mode, the indoor control removes the G signal from the board. This slows the motor to 75 percent of heat pump airflow. If the CFM adjust is set to LO, it will deliver 67.5 percent of heat pump airflow during Super Comfort Heat mode.

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 11

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

Troubleshooting
Troubleshooting Easy Select Board (FV4, FT4)
If Traces Are Overheated on Back of PCB:
Usually whenever there is a trace broken on PCB, it means either there has been a high-voltage short or high voltage has been applied to low-voltage circuit. This can be prevented by making sure PCB is wired correctly before fan coil has power applied to it.
If PCB Fuse Keeps Blowing:
When low-voltage fuse blows, it means transformer would have blown if fuse had not been in circuit to protect it. The fuse usually blows when there is a high current drawn on transformer, high voltage applied to low-voltage circuit, or a direct secondary short. When there is a high current drawn on transformer, it is most likely because transformer has been shorted or system is trying to draw more VAC than transformer rating allows. When fuse blows because of high voltage, the system has mixed high and low-voltage signals.
1. Check transformer and thermostat wiring (Fig. 8). Be sure transformer is not shorting out because thermostat wires are miswired.
2. Check wiring of relays (Fig. 8). Be sure low-voltage and high-voltage wiring are connected to proper sequencers.
3. Check VA draw on transformer. If VA draw is more than VA rating of transformer, fuse will blow. If this is the case, replace transformer with one that has a higher VA rating.
Troubleshooting Common Problems
Airflow Too Low: ­ Y1 instead of Y/Y2 on single-speed air conditioner or heat pump application. Y1 input is only for two-speed applications. Using this terminal will deliver about 60 percent of full cooling airflow. ­ Wrong Easy Select Board selection. Selecting an outdoor unit or electric heater smaller than actually installed will result in low airflow for the application. ­ G not energized with call for cooling or heating. This triggers Super Comfort Heat or SuperDehumidify mode which delivers 50 percent of cooling airflow. ­ J1 jumper pulled with no thermidistat or dehumidistat installed. The J1 jumper ties the DH terminal to R and is installed at the factory. When pulled, a Thermidistat or dehumidistat supplies a 24V signal to DH when there is no call for dehumidification (reverse logic). When there is no signal on DH, the motor reduces airflow to 80 percent for better dehumidification.
Airflow Too High: ­ Wrong Easy Select Board selection. Fan coil is factory set for the largest outdoor unit and largest electric heater. Select sizes that are actually installed. ­ Continuous fan set too high for two-speed applications. Set to MED or LO.
Motor Will Not Stop: ­ Allow time for off delay to time out. In units built before serial number 0101A, any W call will have a two-minute off delay independent of delay selection. This is programmed into the motor and cannot be overridden. ­ In units built after 0101A, the off delay on any W call is one minute and cannot be overridden. ­ Some power-stealing thermostats could bleed enough voltage to cause motor to run slowly when there is no heating or cooling call. Disconnect thermostat wires and wait two minutes to see if motor stops. If it stops, replace thermostat, or install resistor per thermostat installation instructions.
Motor Will Not Start: ­ See following section, “Troubleshooting ECM2.3/5.0 Motor and Controls.”

Troubleshooting ECM2.3/5.0 Motor and Controls
! CAUTION
ELECTRICAL OPERATIONS HAZARD Failure to follow this caution may result in equipment damage or improper operation. High voltage is always present at motor. Disconnect power to unit before removing or replacing connectors or servicing motor. Wait at least five minutes after disconnecting power before opening motor.
The ECM/ICM motor used with this product contains two parts: the control module and the motor winding section. Do not assume the motor or module is defective if it will not start. Go through the steps described below before replacing control module, Easy Select Board or entire motor. The control module is available as a replacement part. If Motor Turns Slowly: 1. It is normal operation to run noticeably slower if G terminal is not
energized in cooling or heat pump heating modes. 2. Attach blower access panel. Motor may appear to run slowly if
access panel is removed. If Motor Does Not Run: Turn power off, wait five minutes and check the following:
1. With power turned off, check 5A fuse on Easy Select Board. 2. Check all plugs and receptacles for any deformation or corrosion
that could cause bad connections. Be sure plugs are fully seated.
! CAUTION
ELECTRICAL OPERATION HAZARD Failure to follow this caution may result in equipment damage or improper operation. DO NOT remove or apply 5-pin plug on motor with power on. Arcing could occur, which can damage control module.
Turn power back on and check the following: 3. Check for 24VAC on SEC1 and SEC2. If no voltage is present,
check transformer. 4. Verify that approximately 230VAC is present at motor. 5. Verify low voltage control signals to motor according to procedure
below. Use following procedure to check low voltage signals: The ECM motor in these fan coils receive low voltage signals from the Easy Select Board through the wiring harness assembly. The combination of pins energized at the motor determines the speed the motor will run. The procedure below isolates the fan coil from all external devices such as a thermostat, condensing unit, humidifier or electronic air cleaner. There is also a specific troubleshooting example to demonstrate the process. Table 7 provides information needed to verify that the correct voltages are present at the motor and the Easy Select Board. THERMOSTAT: 1. Remove all thermostat and accessory wires from Easy Select
Board. 2. On Easy Select Board, jumper screw terminals (1 at a time): R-G,
R-Y/Y2, R-Y1, R-W1, R-W2. If motor runs in all cases, check thermostat outputs. Thermostat wires may be broken, or thermostat may be miswired, configured incorrectly, or defective. If the motor does not run, or runs in some cases, but not others, continue this procedure to check wiring harness and circuit board. WIRING HARNESS:

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 12

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

1. Remove 16-pin/4-pin plug from motor.
2. Check for appropriate voltages on 16-pin/4-pin connector with screw terminals jumpered (Table 3).

4. If voltage is present, the wiring harness is bad. If not, the Easy Select Board is bad.
Verify Motor Winding Section:

3. If signals check correctly, and motor does not run, inspect wiring harness for loose pins or damaged plastic that could cause poor connections.

Before proceeding with module replacement, check the following to ensure motor winding section is functional. With control module removed and unplugged from winding section:

4. If connections are good, either control module or motor is defective.
5. If proper signals are not present, check circuit board using procedure below:
6. If the unit contains a motor signal translator box (16X4), repeat these steps with the connections on these connectors.
12-PIN PLUG (PL-1) ON EASY SELECT BOARD:
1. Completely disconnect wire harness from Easy Select Board.
2. Jumper the screw terminals one at a time; R-G, R-Y/Y2, R-Y1, R-W1, R-W2 and check for appropriate voltages on the Easy Select Board pins. If proper signals are not present, replace Easy Select Board. If proper signals are present at the pins and not at 16-pin connector to the motor, the wiring harness is defective.
TROUBLESHOOTING EXAMPLE:
Motor is not running on a call for heat pump heating after jumpering the Easy Select Board screw terminals as described in Thermostat section above.
With all thermostat wires removed from Easy Select Board, place a jumper wire between R and Y/Y2 low-voltage screw terminals on the Easy Select Board.
1. Check Table 6 for pin number on 16-pin connector associated with the Y/Y2 signal. The correct pin is No. 14. The far right column of the table shows that (-)12VDC should be present between Pin No. 14 and Pin No. 1 (common) on the 16-pin connector.
2. Set meter to read DC voltage. Place meter leads between Pins No. 1 (common) and No. 14 and check for (-)12VDC. If signal is present, the problem is in the module or motor. If signal is not present, the problem is either in wiring harness or Easy Select Board.
These steps can be repeated for other modes of operation.
To check Easy Select Board:
1. Leave jumper wire in place between R and Y/Y2.
2. Check Table 6 under “Volt Meter on Easy Select Board Plug” column and row for Pin No. 14 on motor plug to see pin number on Easy Select Board that should have voltage. The correct pin is No. 2. The column on far right will show voltage that should be present between Pin No. 2 and Pin No. 9 (common).
3. Place meter leads between Pins No. 2 and No. 9 on Easy Select Board and check for (-)12VDC.

1. The resistance between any two motor leads should be similar.
2. The resistance between any motor lead and the unpainted motor end plate should be greater than 100,000 ohms.
If motor winding fails one of these tests, it is defective and must be replaced.
Accessories
AUXILIARY TERMINALS–The AUX and HUM terminals on the Easy Select Board are tied directly to the G terminal, and provide a 24VAC signal whenever the G terminal is energized (Fig. 10). During Superdehumidify mode, the G signal is not present and the auxiliary terminals are not energized. If the installation includes the use of this operating mode, do not use these terminals to control accessories. See Electronic Air Cleaner and Humidifier sections for further information.
ELECTRONIC AIR CLEANER CONNECTIONS–The AUX1 and AUX2 terminals are not always energized during blower operation, as described above. When using an electronic air cleaner with the FV4 fan coil, use Airflow Sensor. The airflow sensor turns on electronic air cleaner when the fan coil blower is operating.
HUMIDIFIER / HUMIDISTAT CONNECTIONS–Easy Select Board terminals HUM1 and HUM2 are provided for direct connection to the low-voltage control of a humidifier through a standard humidistat. These terminals are energized with 24VAC when G thermostat signal is present. Alternately, the 24VAC signal may be sourced from the W and C terminal block connections when electric heaters are used as primary heating source. When using a ThermidistatTM Control, Zone Perfect Plus, or Comfort Zone II, the 24VAC signal may be source directly from the Thermidistat HUM terminal.
Dehumidify Mode
NOTE: Humidistat must open on humidity rise.
Latent capacities for systems using the FK4, FT4, FV4, and 40FK fan coils are better than average systems. If increased latent capacity is an application requirement, the field wiring terminal block provides connection terminals for use of a standard humidistat. The FK4, FT4, FV4, and 40FK fan coils will detect the humidistat contacts opening on increasing humidity and reduce its airflow to approximately 80 percent of nominal cooling mode airflow. This reduction will increase the system latent capacity until the humidity falls to a level which causes the humidistat to close its contacts. When the contacts close, airflow will return to 100 percent of the selected cooling airflow. To activate this mode, remove jumper J1 and wire in a standard humidistat. Carefully consult product airflow data for cooling and dehumidification modes.

Table 6 ­ FV4/FT4 Motor Control Test Values (With 16-pin connector at motor unplugged)

Terminals Jumpered

Volt Meter on 16-pin Harness Plug

Volt Meter on 12-pin Easy Select Board Plug

Voltage

­

­

R to W1

Pin 2

Pin 1

Pin 7

Pin 9

24VAC

R to W2

Pin 13

Pin 1

Pin 4

Pin 9

24VAC

R to Y1

Pin 6

Pin 1

Pin 3

Pin 9

(-)12VDC

R to Y/Y2

Pin 14

Pin 1

Pin 2

Pin 9

(-)12VDC

R to G (LO)

Pin 15

Pin 1

Pin 3

Pin 9

0VAC

R to G (MED)

Pin 6

Pin 1

Pin 3

Pin 9

(-)12VDC

R to G (HI)

Pin 14

Pin 1

Pin 2

Pin 9

(-)12VDC

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 13

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

FAN COIL
AUX1 AUX2 (C) (G)

230 VAC OR 115 VAC BRANCH CKT
GND HOT NEUT

WHT

BLK

GRN

RED RED

BLK

24 VAC RELAY NO
COM

WHT
TO EAC BLK

temperature, supply and return air temperatures, and blower motor RPMs. The dealer’s unique contractor PIN can be located through either of these applications.
Power On LED/Board States The amber LED is illuminated solid when there is power to the product. The green LED is illuminated solid when there is communication between the board and the InteliSense-enabled thermostat.
Table 7 ­ Diagnostic Code List*

Code

Description

30.1

InteliSense Communication Loss

30.2

InteliSense Communication Board Fault

52.1

Supply Air Temperature Open Fault

52.2

Supply Air Temperature Short Fault

53.1

Return Air Temperature Open Fault

53.2

Return Air Temperature Short Fault

Fig. 11 ­ KFAIR0201ACR Relay Kit Wiring Schematic A98625
EASY SELECT BOARD TERMINAL
BLOCK

J1

DH

REMOVE

R

JUMPER

HUMIDISTAT

Fig. 12 ­ Humidistat Wiring for De-Humidify Mode A95316
InteliSenseTM Technology (FT4)
This unit is InteliSense capable when used with an InteliSense thermostat. InteliSense allows for the collection of performance data in the cloud. The unit comes with two interchangeable sensors: a Return Air Temperature (RAT) sensor and a Supply Air Temperature (SAT) sensor for installation in the field. Make sure the sensors are connected to the appropriate terminals for proper temperature data collection when used with the InteliSense board. See installation instructions for detailed information on RAT/SAT placement and installation.
The InteliSense board uses the existing Easy Select layout for airflow selection with additional circuitry to manage the InteliSense data collection. Refer to the thermostat instructions for Easy Select operation details.
NOTE: When installing and servicing electronic equipment use appropriate safety PPE and avoid damaging system components by utilizing electrostatic discharge protection.
Connected Portal and Service Tech App
The Carrier Connected portal and Service Tech App provide a connection between the dealer/service tech and the homeowner’s system. They can provide information about the homeowner’s account, equipment configuration, operating performance and fault code history, current equipment status, and allow you to view and update thermostat settings. They can perform remote service diagnostics using real time suction line temperature and pressure w/ superheat calculation, liquid line temperature and pressure with subcooling calculation, outdoor air

*. Refer to the Service Tech App or Connected Portal for more information. Timestamps shall be applied to the fault when it occurs. Fault codes can be read
through the dealer portal or through the service tech app.

How to Troubleshoot RAT/SAT Functionality
One method of determining RAT/SAT functionality is to compare the actual resistance of the sensor with the nominal resistance at sample temperatures. The table below indicates several example values in the operating range of the sensors.
Communication Loss and Board Fault
Refer to thermostat advanced installation and configuration instructions found at carrier.hvacpartners.com/InteliSense.
Table 8 ­ RAT/SAT Sensor Values

Temperature (°F) Nominal Resistance (K-ohms) Tolerance (± %)

23

42.6

5.92

32

32.8

2.85

41

25.5

2.76

50

19.9

2.68

59

15.7

2.59

68

12.5

2.51

77

10.0

2.44

86

8.1

2.37

95

6.5

2.30

104

5.3

4.48

How Does the Service Tech Know when the System is Functioning Properly?
InteliSense is fully functioning when communication is established (indicated by LED or through the thermostat) and the thermostat has successfully fully learned all of the equipment and data is being displayed on the Connected Portal/service tech app.
FE4
Model FE4 fan coil is designed to be installed with a communicating user interface. The FE4 fan coil will provide airflow at a rate commanded by the User Interface. The nominal airflow/ton rate is 350 CFM/ton. The User Interface will modify the commanded airflow under certain operating modes. Refer to the User Interface literature for further system control details. This fan coil will not respond to commands from

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 14

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

a common thermostat except under certain emergency situations explained in this document.
Electronically Commutated Motor ECM 3.0
An ECM 3.0 is fed high voltage AC power through the 5-pin connector. The AC power is then internally rectified to DC by a diode module. After rectification, DC signal is electronically communicated and fed in sequential order to 3 stator windings. The frequency of these communication pulses determines motor speed. The rotor is permanently magnetized.
ECM 3.0 Control Power
The ECM 3.0 control power is supplied from R circuit through printed circuit runs to motor control connector Plug 1, Pin 1, through motor control harness to motor. The C side of low-voltage control power circuit is connected by printed circuit runs to motor connector Plug 1, Pin 2 then through motor control harness to motor. A digital signal is sent from Plug 1, Pins 3 and 4 to communicate with the motor including all airflow requirements.
Low-Voltage Circuit Fusing and Reference
The low-voltage circuit is fused by a board-mounted 5A automotive type fuse placed in series with transformer SEC2 and R circuit. The C circuit of transformer is referenced to chassis ground through a printed circuit run at SEC1 connected to metal standoff.
NOTE: The PCB must be mounted with two screws and motor ground lead secured to blower housing or erratic motor operation can result.
Transformer, Motor, and Electric Heater Power Connection
Transformer high voltage supplied from electric heater package or high voltage leads through 12-pin heater connector plug/recp2. The ECM 3.0 power connections are made at the transformer primary terminals. The transformer secondary connections are made at SEC1 and SEC2 connectors.
Troubleshooting (FE4)
NOTE: Always check high and low voltage supply to the fan coil components. Check the integrity of the plug receptacle connections and fan coil wiring harness prior to assuming a component failure.
LED Description
LEDs built into fan coil control provide installer or service person information concerning operation and/or fault condition of the fan coil control and ECM motor. This information is also available at system User Interface in text with basic troubleshooting instructions. Careful use of information displayed will reduce the need for extensive manual troubleshooting.
The amber LED located at bottom center of control adjacent to motor harness plug is Motor Status LED, and it is labeled MOTOR. A second amber LED, located in upper right center of control adjacent to System Communications connector (A,B,C,D) is the System Status LED, and it is labeled STATUS. The green LED labeled COMM is also located adjacent to System Communications connector, below STATUS LED, and is used as an indicator of system communications status. Status Codes will be displayed on the STATUS LED using the following protocol:
1. The number of short flashes indicates first digit of code.
2. The number of long flashes indicates second digit of code.
3. A short flash is 0.25 seconds on. A long flash is one second on.
4. The time between flashes is 0.25 seconds.
5. The time between last short flash and first long flash is 1 second.
6. The LED will be off for 2.5 seconds before repeating code.
Fan Coil Control Start-Up and System Communications Troubleshooting
On power up, green COMM LED will be turned off until successful system communications are established (this should happen within 10 seconds). Once communications with User Interface are successful,

COMM LED will be lit and held on. At the same time, amber STATUS LED will be lit and held continuously on until a request for operating mode is received. The STATUS LED will be on any time fan coil is in idle mode.
If, at any time, communications are not successful for a period exceeding two minutes, fan coil control will only allow emergency heating or cooling operation using a common thermostat, a non-communicating outdoor unit and the R, C, Y, O, W outdoor unit terminal strip connections and will display Status Code 16, System Communication Fault, on amber STATUS LED. No further fan coil troubleshooting information will be available at User Interface until communications are re-established.
If COMM LED does not light within proper time period and status code is not displayed:
1. Check system transformer high and low voltage to be sure the system is powered.
2. Check fuse on fan coil control to be sure it is not blown. If fuse is open, check system wiring before replacing it to be sure a short does not cause a failure of replacement fuse.
If COMM LED does not light within proper time period and status code is displayed:
Check system wiring to be sure User Interface is powered and connections are made A to A, B to B, etc. and wiring is not shorted. Mis-wiring or shorting of the ABCD communications wiring will not allow successful communications.
NOTE: Shorting or mis-wiring low voltage system wiring will not cause damage to fan coil control or User Interface but may cause low voltage fuse to open.
ECM Motor Troubleshooting
The ECM motor used in this product consists of two parts: the control module and the motor winding section. Do not assume motor or module is defective if it will not start. Use the designed-in LED information aids and follow troubleshooting steps described below before replacing motor control module or entire motor. Motor control module is available as a replacement part.

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 15

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

Fig. 13 ­ FE4 ECM 3.0 Motor Vefify Motor Winding Section

A12231

! WARNING
ELECTRICAL SHOCK HAZARD Failure to follow this warning could result in personal injury or death or possible equipment damage. After disconnecting power from the ECM motor, wait at least five minutes before removing the control section. Internal capacitors require time to discharge. Minor injury from electrical shock may result from early contact with live metal parts.

Before proceeding to replace a motor control module:
1. Check motor winding section to be sure it is functional.
2. Remove motor control module section and unplug winding plug. Motor shaft should turn freely, resistance between any two motor leads should be similar and resistance between any motor lead and unpainted motor end should exceed 100,000 ohms.
3. Failing any of these tests, entire ECM motor must be replaced.
4. Passing all of the tests, motor control module alone can be replaced.
Motor Turns Slowly 1. Low static pressure loading of blower while access panel is
removed will cause blower to run slowly. Particularly at low airflow requests. This is normal, do not assume a fault exists.

2. Recheck airflow and system static pressure using User Interface service screens with access panel in place.
NOTE: Blower motor faults will not cause a lockout of blower operation. Fan coil control will attempt to run the blower motor as long as User Interface maintains a demand for airflow. Fan coil control will not operate electric heaters while a fault condition exists. The fan coil control communicates with the motor at least once every five seconds, even when the motor is idle. If, during operation, the fan coil control does not communicate with the motor for more than 25 seconds, the motor will shut itself down and wait for communications to be reestablished.
Using Motor LED in Troubleshooting
The MOTOR LED is connected to the blower motor communication line and works with the fan coil control microprocessor and the STATUS LED to provide fan coil operation and troubleshooting information. When the motor is commanded to operate, the MOTOR LED will be turned on and will flash each time instructions are sent to the motor. When the motor is commanded to stop, the MOTOR LED will be turned off.
If the MOTOR LED is lit, flashing and the motor is running or if the MOTOR LED is off and the motor is stopped, operation is normal and no motor fault exists.
If the MOTOR LED is lit, flashing and the motor does not run, or if the MOTOR LED is off and the motor is running, check the STATUS LED for the Status Code. Refer to the troubleshooting instructions for the indicated Status Code in Section E, Fan Coil Troubleshooting.
Fan Coil Troubleshooting
Fan coil faults indicated by flashing codes on the amber system STATUS LED can be resolved using troubleshooting information provided below. Codes are listed in order of their priority, highest to lowest. Though multiple faults can exist at any time, only the highest priority code will be displayed on STATUS LED. Clearing the indicated fault when multiple faults exist will cause the next highest priority Status Code to be flashed. All existing faults, as well as a fault history, can be viewed at User Interface.
STATUS CODE 45, CONTROL BOARD TEST FAULT:
Fan coil control has failed internal start-up tests and must be replaced. No other service procedure will correct.
STATUS CODE 37, HEATER OUTPUT SENSED “ON” WHEN NOT ENERGIZED:
Fan coil control is provided with circuitry to detect presence of a 24VAC signal on Electric Heater stage 1 and stage 2 outputs.
If fan coil control detects a 24VAC signal on either heater stage output and it is not supplying signal, Status Code 37 will be displayed on STATUS LED. Fan coil control will turn off output and command blower motor to supply an airflow determined to be safe for current operation mode with electric heaters energized.
To find the fault:
1. Stop all system operations at User Interface and check heater stage 24VAC outputs.
2. Disconnect electric heater at plug/receptacle 2 and check heater wiring for faults. See Status Code 36 for more information.
STATUS CODE 44, MOTOR COMMUNICATION FAULT:
The MOTOR LED is connected to the blower motor communication line and works with the fan coil control microprocessor and STATUS LED to provide fan coil operation and troubleshooting information.
When motor is commanded to operate, the MOTOR LED will be turned on and will flash each time instructions are sent to the motor.
When the motor is commanded to stop, the MOTOR LED will be turned off. The MOTOR LED will not flash to indicate communications when it is turned off.

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 16

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

Fan coil control is constantly communicating with the motor, even when the motor and MOTOR LED are off. If motor does not acknowledge receipt of communications, the control will display Status Code 44 on STATUS LED and continue to try to communicate with the motor. If motor acknowledges communication, status code will be cleared.
If MOTOR LED is lit and flashing and motor does not run:
1. Check the STATUS LED. If STATUS LED is indicating a Status 44 code, check the motor wiring harness for proper connection to control and motor receptacles.
2. Check motor wiring harness to be sure all wiring complies with wiring diagram description, makes a complete circuit from connector to connector and is not shorted.
3. Check 12VDC low-voltage supply to motor at Pins 1 (+) and 2 (-) of motor header connection to fan coil control.
If all checks are normal, fan coil control is good and control module on motor may need replacement. Check motor and Motor Control Module following the instructions in (ECM Motor Troubleshooting on p15).
Shorted or mis-wiring of the low voltage motor harness wiring will not cause damage to fan coil control or to motor control module.
If the MOTOR LED is off, STATUS LED is indicating a Status Code 44 and motor is running:
Disconnect the motor harness at the fan coil control. If motor continues to run, fan coil control is good and control module on motor may need replacement
STATUS CODE 25, INVALID MOTOR / MODEL SELECTION:
On initial start-up, fan coil control shall poll motor for its size data and check fan coil size data stored in fan coil control memory.
1. If motor size is incorrect for fan coil size or fan coil size data is invalid, Status Code 25 will be displayed on STATUS LED.
2. If model size data is missing (as is the case when a replacement fan coil control is installed), system User Interface will prompt installer to enter correct model size from a list of valid sizes.
3. If motor size is incorrect for model size, motor must be replaced with proper size motor. Fan coil control will not respond to operation requests until this fault condition is resolved.
STATUS CODE 27, INVALID OUTDOOR UNIT SIZE:
On initial power-up, fan coil control will write into memory outdoor unit size as provided by User Interface in a fully communicating system.
1. If outdoor unit size is invalid, Status Code 27 will be displayed on STATUS LED.
2. User Interface will prompt the installer to choose size from a list of valid sizes for application with fan coil.
3. Check communications wiring to be sure User Interface has established communications with outdoor unit or select proper size from valid size list provided at User Interface.
4. Check motor and motor control module following the instructions in (ECM Motor Troubleshooting on p15).
STATUS CODE 26, INVALID HEATER SIZE:
On initial power-up, fan coil control will write into memory electric heater size as read from heater if heater is provided with Identifier Resistor (IDR). Heater size must be valid for combination of indoor and outdoor components installed. Fan coil control will read IDR value connected to Pins 5 and 8 of heater harness connector. If no resistor is found, system User Interface will prompt installer to verify that no heater is installed.
Verifying that this is correct will establish that fan coil is operating without an electric heater accessory. Upon choosing negative option, installer will be prompted to select heater size installed from a list of valid heater sizes for fan coil and outdoor unit size installed.
If heater ID resistor value read is invalid, Status Code 26 will be displayed on STATUS LED.

If heater installed is equipped with a resistor connected to Pins 5 and 8 of heater harness connector and Status Code 26 is displayed on STATUS LED:
1. Check wiring harness connections to be sure connections are secure.
2. If symptoms persist, disconnect wiring harness at fan coil control heater header and check for a resistance value greater than 5000 ohms.
3. Check for proper wiring of resistor assembly.
4. Make sure heater size installed is an approved size for outdoor unit and fan coil sizes installed.
NOTE: Fan coil control will not operate electric heater until this Status Code is resolved. If the heater size is set through the User Interface, the heater will be operated as a single stage heater. If staging is desired, the IDR value must be read in by the fan coil control.
Table 9 ­ FE4 Self-identifying Resistor Values

Heater Size kW

Resistor Ohms Nominal

No heater

Open

9

11k

15

18k

20

24k

24

33k

30

39k

Hydronic Heat

270k

STATUS CODE 36, HEATER OUTPUT NOT SENSED WHEN ENERGIZED:
Fan coil control is provided with circuitry to detect presence of a 24VAC signal on Electric Heater stage 1 and stage 2 outputs.
If fan coil control energizes either heater stage and does not detect the 24VAC signal on output, Status Code 36 will be displayed on the STATUS LED Fan coil control will continue to energize heater output(s) and adjust blower operation to a safe airflow level for energized electric heat stage(s).
To find the fault, check for 24VAC on heater stage outputs. Fan coil control or sensing circuit may be bad.
NOTE: It may be useful as an electric heater troubleshooting procedure to disconnect the system communications to force Status Code 16 enabling of emergency heat mode. It is difficult to know which heater output is energized or not energized in normal operation. When fan coil is operated in emergency heat mode using electric heaters, both outputs are energized and de-energized together. Terminal strip inputs to control can then be connected R to W to turn on both electric heat outputs. Heater output sensing circuits can then be checked to resolve Status Code 36 or 37 problems.
STATUS CODE 41, BLOWER MOTOR FAULT:
If MOTOR LED is lit and flashing and motor does not run:
1. Check STATUS LED. If STATUS LED is indicating Status Code 41, motor control has detected that the motor will not come up to speed within 30 seconds of being commanded to run or that the motor has been slowed to below 250 rpm for more than 10 seconds after coming up to speed. Motor wiring harness and fan coil control are operating properly, do not replace.
2. Check to be sure that the blower wheel is not rubbing the housing.
3. Check motor to be sure that the motor shaft is not seized (motor control module must be removed and electronics disconnected from windings to perform this check properly).
4. Check motor windings section following instructions in (ECM Motor Troubleshooting on p15).

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 17

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

If all these checks are normal, the motor control module may need replacement.
STATUS CODE 16, SYSTEM COMMUNICATION FAULT:
If, at any time, system communications are not successful for a period exceeding two minutes, the fan coil control will only allow emergency heating or cooling operation using a common thermostat, a non-communicating outdoor unit, and the R, C, Y, O,W outdoor unit terminal strip connections and will display Status Code 16 on the amber STATUS LED. See (Emergency Heating and Cooling Modes on p18). No further fan coil troubleshooting information will be available at the User Interface until communications are reestablished.
Check system wiring to be sure the User Interface is powered and connections are made A to A, B to B, etc. and wiring is not shorted. Mis-wiring or shorting of the ABCD communications wiring will not allow successful communications. Correcting wiring faults will clear the code and reestablish communications.
Shorting or mis-wiring the low voltage system wiring will not cause damage to fan coil control or to User Interface but may cause the low voltage fuse to open.
STATUS CODE 46, BROWNOUT CONDITION:
If the secondary voltage of the transformer falls below 15VAC for a period exceeding four seconds, Status Code 46 will be displayed on STATUS LED.
If system includes a non-communicating outdoor air conditioner or heat pump, the User Interface will command the fan coil to turn off Y output controlling compressor.
When secondary voltage rises above 17VAC for more than four seconds, the brownout condition is cleared and normal system operation will resume subject to any minimum compressor off delay function which may be in effect. Brownout does not affect blower or electric heater operation.
STATUS CODE 53, OUTDOOR AIR TEMPERATURE SENSOR FAULT:
If an OAT sensor is found at power-up, input is constantly checked to be within a valid temperature range. If sensor is found to be open or shorted at any time after initial validation, Status Code 53 will be displayed at amber STATUS LED.
Check for faults in wiring connecting sensor to OAT terminals. Using an Ohmmeter, check resistance of thermistor for a short or open condition.
If thermistor is shorted or open, replace it to return the system to normal operation. If fault is in the wiring connections, correcting the fault will clear the code and return the system to normal operation.
NOTE: If fault condition is an open thermistor or a wiring problem that appears to be an open thermistor and the power to the fan coil control is cycled off, the fault code will be cleared on the next power-up but the fault will remain and system operation will not be as expected. This is because on power-up, the fan coil control cannot discern the difference between an open sensor or if a sensor is not installed.
Emergency Heating and Cooling Modes
Fan coil control can provide emergency heating or cooling using a common heat/cool thermostat in the event that there are no system communications, fault is in User Interface and no replacement is immediately available.
To activate these modes, the thermostat and outdoor unit must be wired as a common heating/cooling system to fan coil control RYWC terminals. Fan coil control must be powered and displaying Status Code 16, System Communication Fault.
NOTE: These emergency modes do not provide the level of comfort and efficiency expected by the consumer and should only be activated when User Interface cannot be replaced immediately.

SEQUENCE OF OPERATION The FE4 fan coil is designed for installation with a communicating User Interface. This fan coil will not respond to commands provided by a common thermostat except under certain emergency situations described in the Start Up and Troubleshooting sub-section. The User Interface uses temperature; humidity and other data supplied from indoor and outdoor system components to control heating or cooling system for optimum comfort. ADVANCED TROUBLESHOOTING:
Status LED
Communication LED

Motor LED

Fig. 14 ­ Circuit Board LED Locations

A13030

Troubleshooting the FE4 Fan Coil Circuit Board: ­ Production Unit circuit board Fan Coil part number HK38EA061 ­ RCD Replacement circuit board HK38EA061 ­ Older circuit board part numbers HK38EA006, HK38EA009, and HK38EA011
Primary test that should be performed: Motor Line Voltage Check 1. Turn off power (240V). 2. Remove Plug 3 from ECM motor 3. Turn on power. 4. Check Plug 3, terminals 4 and 5, to ensure there are 240V. 5. Turn off power. 6. Reconnect Plug 3 to motor.

Fig. 15 ­ ECM / Plug Wiring Diagram
Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 18

A13031

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

The following troubleshooting techniques will assist in determining the correct component to replace when the Fan Coil Board presents a Fault Code 44 or 41:
1. Disconnect power from the unit (240V).
2. Disconnect the ABCD connector from the board.
3. Disconnect Plug 1 from the board (Fig. 15).
4. Turn on power (240V).
5. After reestablishing power, you should receive Fault Code 44, and the motor LED should be off.
6. Place a jumper across the R and G terminals on the low voltage terminal block
7. Fault Code 44 should still be flashing.
8. The Motor LED should be flashing, indicating the board is able to transmit a signal to the motor.
9. If Motor LED is not flashing, check to ensure that 24V is present across R and C on the low voltage terminal block and that there is a good connection with the R and G jumper.
10. If 24V is present and the jumper/connections are good,
11. Replace the board.
Check Board
1. If Fault Code 44 and the Motor LED are both flashing, place a DC voltmeter across terminals PL1-1 Red (+) to PL1-2 Green (-) (Fig. 15).
2. Across terminal PL1-1 and PL1-2, a 12VDC should be present. If 12VDC is not present, replace circuit board.
3. If Fault Code 44 is flashing and the Motor LED is flashing, place a DC voltmeter across terminal PL1-3 (+) and PL1-2 (-).
4. Across terminal PL1-3 (+) and PL1-2 (-), the DC volt meter should display 5VDC. The voltage should be very stable and should not fluctuate more than 0.02VDC. If the voltage fluctuates, get a different voltmeter before proceeding to the following steps.
5. Reconnect Plug 1 to circuit board and connect DC voltmeter across terminals PL1-3 Yellow (+) and PL1-2 Green (-). Does the voltage appear to fluctuate more than in step 15? Typical voltmeters will show a fluctuation of 0.2VDC to 1VDC. The amount of fluctuation is not important. You could see even more fluctuation depending on the voltmeter used.
6. Check the blower motor serial output signal. The blinking LED on the control board represents the serial output signal. You can measure the signal with a DC voltmeter by removing Plug 1 from the circuit board and connecting the DC voltmeter across PL1-4 (+) and PL1-2 (-). The voltage should be near 0VDC but it will fluctuate briefly several times per second. If you have an analog voltmeter, the needle briefly will go high several times per second. If you have a digital voltmeter with a bar graph, it will show a large change in magnitude on the bar graph several times per second. If you have a plain, digital voltmeter, it will show a brief fluctuation in voltage, and the magnitude may vary depending on the voltmeter used.
! WARNING
ELECTRICAL SHOCK HAZARD Failure to follow this warning could result in personal injury or death. Disconnect all power to the unit before servicing the field wires or removing the control package. The disconnect (when used) on the access panel does not disconnect power to the line side of the disconnect, but does allow safe service to all other parts of the unit.
The minimum maintenance requirements for this equipment are as follows:
1. Inspect and clean or replace air filter each month or as required.

2. Inspect cooling coil, drain pan, and condensate drain each cooling season for cleanliness. Clean as necessary. An inspection port is provided on all A-coil delta plates. Remove plastic plug to inspect. Replace plug after inspection.
3. Inspect blower motor and wheel for cleanliness each heating and cooling season. Clean as necessary.
4. Inspect electrical connections for tightness and controls for proper operation each heating and cooling season. Service as necessary.
! CAUTION
CUT HAZARD Failure to follow this caution may result in personal injury.
Sheet metal parts may have sharp edges or burrs. Use care and wear appropriate protective clothing and gloves when handling parts.
Filter Assembly To clean or replace air filter, push plastic connectors toward center of unit and remove filter access panel outward. Push filter up and back into unit. Then slide filter out.
Clean filter by using cold water and mild detergent. Rinse and allow filter to dry. No oiling or coating of filter is required. New filters are available from your local distributor. Place filter in slot with cross-mesh binding up or facing cooling coil and replace filter access panel. Cooling Coil, Drain Pan, and Condensate Drain The cooling coil is easily cleaned when it is dry. Inspect the coil and clean (if necessary) before each cooling season. To check or clean cooling coil, remove coil access panel. If coil is coated with dirt or lint, vacuum it with a soft brush attachment.
Be careful not to bend coil fins. If coil is coated with oil or grease, clean it with a mild detergent and water solution. Rinse coil thoroughly with clear water. Be careful not to splash water on insulation.
FFM and FMA
! WARNING
ELECTRICAL OPERATION HAZARD Failure to follow this warning could result in personal injury or death. Before installation or servicing system, always turn off main power to system. There may be more than one disconnect switch. Turn off accessory heater power if applicable. Lock out and tag switch with a suitable warning label.
Fan Motor The FFMANP(018,024,030,036) and FMA4Pmotor is three-speed PSC direct drive. High-speed lead is black, medium-speed lead is red, low-speed lead is blue, and common lead is purple. The FFMANP(019,025,031,037) and FMA4Xmotor is a five speed ECM direct drive. The cooling speed tap is selected by connecting the green wire to the desired motor tap number indicated on the motor plug. For the electric heat fan speed selection connect the white wire to the desired motor tap number indicated on the motor plug. Be sure proper blower speed has been selected.
The blower motor in this unit has blower-off delays. The blower-off delay is 30­90 seconds and will keep the motor running after a heating or cooling call ends.
The motor is turned on through two different routes. The first occurs when thermostat calls for the fan in cooling, heat pump, or fan-only mode. A 24VAC signal is sent to relay, causing relay to close its normally open contacts, turning fan on.

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 19

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

The second occurs when there is a call for electric heat. A 24VAC signal is sent to heater sequencer/relay, causing it to close, directing 230V through the normally closed contact of fan relay, turning fan on. The fan remains on until sequencer/relay/PCB opens.
If motor does run, test motor for an open winding or a winding shorted to motor case. If either is present, replace motor.
Time Delay
FFMANP(019,025,031,037) and FMA4X have time delay built into the motor logic. FFMANP(018,024,030,036) and FMA4P units with date codes prior to 1715V have sequencers. FFMANP(018,024,030,036) and FMA4P units with date codes 1715V or later have a time delay printed circuit board.
The Time Delay Printed Circuit Board (PCB) s a logic controlled time delay activated by low-voltage control signal (G) from thermostat. The PCB includes a normally open relay which closes to energize the blower motor when the G terminal is energized. Then when the G terminal is de-energized the relay energizing the blower motor remains closed for 90­100 seconds before opening.
NOTE: Aluminum coil models with PSC motor can be wired to different OFF time delay. See installation instructions for wiring diagram.
NOTE: The following sequence of operation is based on units installed with PSC motor and Time Delay Printed Circuit Board (PCB). For units with ECM motor, the off-delay is programmed into the motor. Follow Table 10 below, ECM Motor Speed Taps & the corresponding blower OFF delays for each speed tap.
Continuous Fan
Thermostat closes R to G. G energizes and completes circuit to indoor blower motor. When G is de-energized, there is a 90-second blower off-delay.
Cooling Mode
Thermostat energizes R to G, R to Y, and R to O (heat pump only). G energizes and completes indoor blower motor. Y energizes outdoor unit (O is energized for heat pump). When cooling call is satisfied, G is de-energized, there is a 90-second blower off-delay.
Heat Pump Heating Mode
Thermostat energizes R to G and R to Y. G energizes and completes circuit to indoor blower motor. When heating call is satisfied, G is de-energized, there is a 90-second blower off-delay.
Heat Pump Heating with Auxiliary Electric Heat
Thermostat energizes R to G, R to Y, and R to W1. G energizes and completes circuit to indoor blower motor. W1 energizes electric heat relay(s) which completes circuit to heater element(s). When W1 is de-energized, electric heat relay(s) open, turning off heater elements. When G is de-energized there is a 90-second blower off-delay.
Electric Heat or Emergency Heat Mode
Thermostat closes R to W1. W1 energizes electric heat relay(s) which completes circuit to heater element(s). Blower motor is energized through normally closed contacts on fan relay. When W1 is de-energized, electric heat relay(s) opens, there is no blower off-delay. (units with ECM motor will have a blower off-delay based on motor speed tap selection).
Table 10 ­ Speed Tap and Off -Delay Time

Speed Off-Delay

Tap

Time

18

24

30

36

Tap 1

30

–

–

–

–

Tap 2

90

Default

–

Default

–

Tap 3 Tap 4 Tap 5

Table 10 ­ Speed Tap and Off -Delay Time

30

–

–

–

90

–

Default

–

30

–

–

–

Default
–

Comments: 1. The THR and THC are connected to transformer output. 2. When the G has signal, the FAN will supply 24VAC power
to control fan relay. 3. Whe the G signal is gone, the FAN will stop 24 VAC output
after 90 seconds. 4. CN3, CN7 are dummy connection terminals.

Fig. 16 ­ Time Delay PCB Schematic

A150455B

Fig. 17 ­ 18 & 24 PCB
Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 20

A150462

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

Fig. 18 ­ 30 & 36 PCB

A150463

Fig. 19 ­ Time Delay Schematic

A180074

Electric Heater Service Service can be completed with heater in place. Shut off power before servicing.
Limit Switch
Refer to (Electric Heater Function and Troubleshooting on p25).
Sequencer
Early EHK2 heater kits included sequencers instead of relays. Refer to (Electric Heater Function and Troubleshooting on p25).
Transformer
A 40VA transformer supplies 24V power for control circuit. Check for 208/230V on primary side of transformer. If present, check for 24V on secondary side.
NOTE: Transformer is fused. Do not short circuit. Fan Relay
Later EHK2 heater kits included relays instead of sequencers. Relay coil is 24V. Check for proper control voltage. Replace relay if faulty.
Cleaning or Replacing Refrigerant Flow-Control Device FFM, FMA4P
The piston can be removed and cleaned if believed to be plugged. This unit’s piston is unique and replacements are available from RCD.
The filter drier should be located on the liquid line at the indoor unit to prevent particulate from plugging the piston.

FFM, FMA4X
These fan coils use an R-410A TXV. The TXV’s are preset at the factory and do not need adjustment for reliable operation. Reference the outdoor unit instructions to properly charge the unit to the correct subcooling. For optimal performance, adjust the TXV so that 6º F of superheat is measured at the outdoor unit’s vapor service valve when the indoor return air is 80º F DB/67º F WB and outdoor ambient is 82º F DB. To increase superheat turn the TXV adjustment stem clockwise no more than one rotation at a time. After an adjustment is made, wait until the superheat temperature has been stable for 15 minutes before making further adjustments.
Sequence of Operation
Condensing Unit
COOLING–When thermostat calls for cooling, the circuit between R and G is complete and single-pole single-throw relay FR is energized. The normally open contacts close causing blower to operate.
The circuit between R and Y is also complete. This completed circuit causes contactor in outdoor unit to close which starts compressor and outdoor fan. When thermostat is satisfied, its contacts open de-energizing contactor and blower relay. This stops compressor and outdoor fan motor. The indoor fan motor will stop after 90-100 seconds on the FFMANP(018,024,030,036) and FMA4P, and 30 or 90 seconds on the FFMANP(019,025,031,037) and FMA4X.
HEATING–When thermostat calls for heating and FAN switch is set on AUTO, the circuit between R and W is complete. The heater sequence SEQ is energized which closes contacts of relay. There will be a time delay. This completed circuit energizes all heating elements HTR and blower motor. When thermostat is satisfied, its contacts open de-energizing heat relay. This de-energizes the sequencer. All heaters should stop. The indoor fan motor will stop after 90-100 seconds on the FFMANP(018,024,030,036) and FMA4P, and 30 or 90 seconds on the FFMANP(019,025,031,037) and FMA4X.
Heat Pump
COOLING–On a call for cooling, the thermostat makes circuits R-O, R-Y, and R-G. Circuit R-O energizes reversing valve, switching it to cooling position. Circuit R-Y energizes contactor starting outdoor fan motor and compressor. Circuit R-G energizes indoor unit blower relay starting indoor blower motor.
When thermostat is satisfied, its contacts open de-energizing contactor reversing valve and blower relay. This stops compressor and outdoor fan motor. The indoor fan motor will stop after 90-100 seconds on the FFMANP(018,024,030,036) and FMA4P, and 30 or 90 seconds on the FFMANP(019,025,031,037) and FMA4X.
HEATING–On a call for heating, the thermostat makes circuits R-Y and R-G. Circuit R-Y energizes contactor starting outdoor fan motor and compressor. Circuit R-G energizes indoor blower relay starting blower motor.
Should temperature continue to fall, R-W circuit is made through second-stage room thermostat bulb. Circuit R-W energizes a sequencer bringing on supplemental electric heat.
When thermostat is satisfied, its contacts open de-energizing contactor and sequencer. All heaters should stop. The indoor fan motor will stop after 90-100 seconds on the FFMANP(018,024,030,036) and FMA4P, and 30 or 90 seconds on the FFMANP(019,025,031,037) and FMA4X.

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 21

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

• Louvered Grill Cover is an accessory Fig. 20 ­ FFMA and FMA4 (Sizes 18 & 24) Expanded View – Case

A14213

NOTE: Time delay PCB replaced Time delay relay in new production models.

Fig. 21 ­ FFMA and FMA4 (Sizes 18 & 24) Expanded View – Duct Components, Blower & Electrical Parts

A150305

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 22

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

Fig. 22 ­ FFMA and FMA4 (Sizes 18 & 24) Expanded View – Evaporator Parts & Drain Pan

A13137

• Louvered Grill Cover is an accessory Fig. 23 ­ FFMA and FMA4 (Sizes 30 & 36) Expanded View – Case

A14214

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 23

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

NOTE: Time delay PCB replaced Time delay relay in new production models.
Fig. 24 ­ FFMA and FMA4 (Sizes 30 & 36) Expanded View – Duct Components, Blower & Electrical Parts

A150306

Fig. 25 ­ FFMA and FMA4 (Sizes 30 & 36) Expanded View – Evaporator Parts & Drain Pan
Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 24

A13140

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

Electric Heater Function and Troubleshooting FB4, FE4, FF1E, FH4, FJ4, FV4, FX4, FZ and PF4
IMPORTANT: 2023 model fan coils (FJ4, FT4, FE4B) are designed to use KFFEH electric heaters, and are not compatible with KFCEH heaters.
This section describes KFC, and KFD series electric heaters in exclusion of Smart Heat by examining the functional operation of these heaters.
Description of Electric Heater Components Limit Switch
The limit switch is a temperature sensitive control whose function is to prevent system from overheating in abnormal conditions. The temperature settings often vary from heater to heater due to variations in airflow patterns and element radiant heat conditions.
The devices are sized to remain on-line under heat pump conditions (115° air off coil) and minimum CFM, but trip to prevent outlet air conditions above 200° F or excessive component or duct temperatures.
The device itself consists of a bimetallic disc, which when overheated “snaps through” to open a normally closed high-voltage, high-current switch. When system temperatures cool sufficiently, the switch will automatically reset to its closed position. Normal failure mode for this switch is open.
If a limit switch has been determined to be defective, NEVER BYPASS THE LIMIT SWITCH. When replacing limit switch, ensure that it is replaced with a limit switch of identical opening temperature and closing differential. Limit switches are typically color coded to identify their range.
KFC and KFD Electric Heat Relay
KFC and KFD electric heater packages have relays controlling the heater elements instead of sequencers. A small rectifier PCB is mounted to each relay which converts the incoming 24VAC control signal to DC.
In addition to the rectifier circuit, the second and third stage relays contain a time-on delay circuit of five seconds for second stage, and eight seconds for third stage. When the control signal is removed from the relays, all relays will open with no time-off delay.
Troubleshooting KFC and KFD Series Electric Heaters Discolored Wire Insulation at Terminal
Check quick-connect terminal at discoloration. Connection may be loose, creating a high resistance through connection point.
Fuse Failure
1. Check for shorted wire. Replace wire. Never try to fix wire using electrical tape.
2. Check shorted element. If element is shorted, replace heater.
No Heat
1. Check fuse for failure. If fuse has failed, refer to (Fuse Failure on p25).
2. Check for faulty transformer. Check output voltage of transformer secondary side R (red) and C (brown). Make sure output is between 18VAC and 30VAC. If output voltage is low and input voltage tests normal, replace transformer.
3. Check for miswired heater plug harness.
4. Check limit switch or sequencer failure. These switches should have failed in open position. If output voltage is zero volts, replace switch.
5. Check heater relay and PCB. Control voltage input to PCB should be 24VAC. Output to relay should be 18VDC minimum. If input is present but no output, replace PCB. If output is present, replace relay.

Heater Will Not Turn Off
1. Check low-voltage wiring for miswire.
2. Check for shorted elements to ground.
3. Replace sequencer/relays. They may be stuck closed.
Nuisance Trips
1. Check for low airflow due to dirty filters, blocked registers, or undersized duct.
2. Check blower motor and wheel for proper operation. Excessive current draw of motor will cause internal overload to trip.
3. The fan speed may be low.
FFM, FMA
This section describes EHK2 series electric heaters by examining functional operation of this heater.
Service can be completed with heater in place. Shut off power before servicing.
Description of Electric Heater Components
Limit Switch
The limit switch is a temperature sensitive control that’s function is to prevent system from overheating in abnormal conditions. The temperature settings often vary from heater to heater due to variations in airflow patterns and element radiant heat conditions.
The devices are sized to remain on-line under heat pump conditions (115° F air off coil) and minimum CFM, but trip to prevent outlet air conditions above 200° F or excessive component or duct temperatures. The device itself consists of a bimetallic disc, which when overheated “snaps through” to open a normally closed high-voltage, high-current switch. When system temperatures cool sufficiently, the switch will automatically reset to its closed position. Normal failure mode for this switch is open.
If a limit switch has been determined to be defective, NEVER BYPASS THE LIMIT SWITCH. When replacing limit switch, ensure that it is replaced with a limit switch of identical opening temperature and closing differential. Limits switches are typically color-coded to identify their range.
Sequencer
Early production EHK2 heaters have sequences controlling the heater elements. The sequencer is essentially a thermally-activated time-delay relay normally activated by low-voltage control signals from thermostat. The typical sequencer is a 1- or 2-pole normally open device which energizes within 30 to 70 seconds after application of control signal and de-energizes 60 to 90 seconds after control signal is removed.
In simplistic terms, the sequencers which we use are nothing more than normally open limit switches which sit on top of a small resistive heater. When voltage is applied to this heater, a positive temperature coefficient resistor (PTC), heat is supplied to a bimetallic disc which “snaps through” and closes switch.
The time required for PTC to heat to a sufficient point controls ON timing of device. The time required for disc to cool down when power is removed controls OFF time of device. The PTC can be varied to provide varied timing. Typically a short ON equates to a long OFF.
Because this is a thermally-activated device, ambient conditions affect the ON/OFF cycle. Higher ambient temperature means shorter ON times and longer OFF times.
Application of these devices is such that the first switch ON not only turns on first heater element, but also ensures that indoor fan is energized, because first ON is last OFF. This ensures fan remains ON until the last heater de-energizes. The Time Delay Printed Circuit Board (PCB) is a logic controlled time delay activated by low-voltage control signal (G) from thermostat. The PCB includes a normally open relay which closes to energize the blower motor when the G terminal is energized. Then when the G terminal is de-energized the relay

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 25

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

energizing the blower motor remains closed for 90 ­ 100 seconds before opening. Relays Later production EHK2 heaters have relays controlling the heater elements instead of sequencers. A small rectifier PCB is mounted to each relay which converts the incoming 24VAC control signal to DC. In addition to the rectifier circuit, the second and third stage relays contain a time-on delay circuit of five seconds for second stage, and eight seconds for third stage. When the control signal is removed from the relays, all relays will open with no time-off delay.
Care and Maintenance FB4, FE4, FE4A/B, FH4, FJ4, FT4, FV4, FX4, FZ4, F54 and PF4
To continue high performance, and minimize possible equipment failure, it is essential periodic maintenance be performed on this equipment. The ability to properly perform maintenance on this equipment requires certain mechanical skills and tools. The only consumer service recommended or required is filter maintenance (Filter Assembly on p26)
! WARNING
ELECTRICAL SHOCK HAZARD Failure to follow this warning could result in personal injury or death. Disconnect all power to the unit before servicing the field wires or removing the control package. The disconnect (when used) on the access panel does not disconnect power to the line side of the disconnect, but does allow safe service to all other parts of the unit.
The minimum maintenance requirements for this equipment are as follows: 1. Inspect and clean or replace air filter each month or as required. 2. Inspect cooling coil, drain pan, and condensate drain each cooling
season for cleanliness. Clean as necessary. 3. Inspect blower motor and wheel for cleanliness each heating and
cooling season. Clean as necessary. 4. Inspect electrical connections for tightness and controls for proper
operation each heating and cooling season. Service as necessary.
! CAUTION
CUT HAZARD Failure to follow this caution may result in personal injury. Sheet metal parts may have sharp edges or burrs. Use care and wear appropriate protective clothing and gloves when handling parts.
Filter Assembly To clean or replace air filter, push plastic connectors toward center of unit and remove filter access panel outward. Push filter up and back into unit. Then slide filter out. Clean filter by using cold water and mild detergent. Rinse and allow filter to dry. No oiling or coating of filter is required. New filters are available from your local distributor. Place filter in slot with cross-mesh binding up or facing cooling coil and replace filter access panel. Cooling Coil, Drain Pan, and Condensate Drain The cooling coil is easily cleaned when it is dry. Inspect the coil and clean (if necessary) before each cooling season. To check or clean cooling coil, remove coil access panel. If coil is coated with dirt or lint, vacuum it with a soft brush attachment.

Be careful not to bend coil fins. If coil is coated with oil or grease, clean it with a mild detergent and water solution. Rinse coil thoroughly with clear water. Be careful not to splash water on insulation. Inspect drain pan and condensate drain at the same time cooling coil is checked. Clean drain pan and condensate drain by removing any foreign matter from pan. Flush pan and drain tube with clear water. If drain tube is restricted, it can generally be cleared by high-pressure water. Cut plastic line and work outside condensate pan and away from coil to clean drain tube.
! CAUTION
UNIT DAMAGE HAZARD Failure to follow this caution may result in equipment damage. Do not use caustic household drain cleaners in the condensate pan or near the coil. Drain cleaners can quickly destroy a coil.
Blower Motor and Wheel Clean blower motor and wheel when cooling coil is cleaned.
! WARNING
ELECTRICAL SHOCK HAZARD Failure to follow this warning could result in personal injury or death. Disconnect electrical power before removing any access panels. Lock out and tag switch with a suitable warning label.
To clean blower motor or blower wheel: 1. Remove blower access panel. 2. Remove motor leads from fan coil control. Note lead location for
ease of reassembly. 3. Remove the two outside screws holding blower/motor assembly
against blower deck flange and slide assembly out of cabinet. · Servicing the blower assembly may require the removal of two
screws that attach the blower housing to the fan deck. It is not necessary to reinstall these screws after service. 4. (If applicable) Remove screw in strap holding motor capacitor to blower housing and slide capacitor out from under strap. Remove screw with green wire from blower housing. Mark blower wheel, motor, and motor support in relation to blower housing before disassembly to ensure proper reassembly. Note position of blades on wheel. 5. Loosen setscrew holding blower wheel onto motor shaft. 6. Remove the three bolts holding motor mount to blower housing and slide motor and mount out of housing. Further disassembly should not be necessary as adequate clearance is available. 7. Remove blower wheel from housing by removing cutoff plate from blower housing outlet. Note wheel orientation and cutoff location for reassembly. The blower motor and wheel may be cleaned by using a vacuum with a soft brush attachment. 8. Remove grease with a mild solvent such as hot water and detergent. Be careful not to disturb balance weights (clips) on blower-wheel vanes. Also, do not drop or bend wheel, as balance will be affected. To reassemble blower: 1. Place blower wheel back into housing. Be sure to position correctly for proper location. 2. Reassemble cutoff plate to housing using identified holes from disassembly procedure. 3. Position motor and mount in same position as when blower housing was in unit. Secure motor mount on housing, using removed bolts. Make sure mount or motor is grounded to blower housing.

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 26

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

4. Locate blower wheel setscrew over flat on motor shaft. Rotate wheel in housing. It should not rub housing and should be centered in inlet opening. If not, loosen setscrew and align as necessary.
5. Attach green wire to blower housing with screw. 6. (If applicable). Secure motor capacitor under strap and tighten strap
screw. 7. Slide blower assembly to blower deck. Be sure (once blower is
within the unit casing) to force blower assembly toward control box while sliding assembly into unit to ensure that blower assembly engages deck properly. 8. Fasten blower assembly to deck with screws previously removed. 9. Reconnect electrical leads to fan coil control. 10. Reconnect electrical power to unit and test fan for proper rotation.
FF1E, FFMA, FMA
The minimum maintenance requirements for this equipment are as follows: 1. Inspect and clean or replace air filter each month or as required. 2. Inspect cooling coil, drain pan, and condensate drain each cooling
season for cleanliness. Clean as necessary. 3. Inspect blower motor and wheel for cleanliness each heating and
cooling season. Clean as necessary. 4. Inspect electrical connections for tightness and controls for proper
operation each heating and cooling season. Service as necessary.
! CAUTION
CUT HAZARD Failure to follow this caution may result in personal injury. Sheet metal parts may have sharp edges or burrs. Use care and wear appropriate protective clothing and gloves when handling parts.
Air Filter The air filter should be replaced as needed. NOTE: Refer to the installation instructions and product data for filter dimensions. 2023 product has been designed to accommodate common sized filters.
! CAUTION
UNIT DAMAGE HAZARD Failure to follow this caution may result in equipment damage. Never operate unit without a filter.
Cooling Coil, Drain Pan, and Condensate Drain The cooling coil is easily cleaned when it is dry. Inspect coil and clean (if necessary) before each cooling season. To check or clean cooling coil, remove blower/heater access panel to gain full access to cooling coil. If coil is coated with dirt or lint, vacuum with a soft brush attachment. Be careful not to bend coil fins. If coil is coated with oil or grease, clean it with a mild detergent and water solution. Rinse coil with clear water. Be careful not to splash water onto insulation. Inspect drain pan and condensate drain at same time cooling coil is checked. Clean drain pan and condensate drain by removing any foreign matter from pan. Flush pan and drain tube with clear water. If drain tube is restricted, it can generally be cleared by high-pressure water. Cut plastic line and work outside condensate pan and away from coil to clear drain tube. NOTE: There MUST be a trap in the condensate line. The trap must be at least 3-in. deep, not higher than the bottom of unit condensate drain opening, and pitched downward to an open drain or sump.

! CAUTION
UNIT DAMAGE HAZARD Failure to follow this caution may result in equipment damage.
Do not use caustic household drain cleaners in the condensate pan or near the coil. Drain cleaners can quickly destroy a coil.
Blower Motor and Wheel Clean blower motor and wheel when cooling coil is cleaned.
To clean or service wheel or motor, proceed as follows:
1. Pull unit disconnect (when used) and remove blower access panel.
2. Disconnect motor electrical leads from control box and capacitor. Mark location of wires for reassembly.
3. Remove the three bolts holding motor mount to blower housing while supporting motor shell with hand.
4. Pull motor inlet ring and blower wheel assembly out of blower housing.
5. With blower wheel, inlet ring, and motor mount still attached to motor, place motor on flat, horizontal surface, shaft up. Mark position of wheel on motor shaft for reassembly.
6. Loosen blower wheel setscrew and remove blower wheel from motor shaft.
NOTE: Further disassembly of motor and mount is not necessary as adequate clearance is available to clean motor.
7. Clean blower motor and wheel using a vacuum with a soft brush attachment. Remove grease with a mild solvent such as hot water and detergent. Be careful not to disturb balance weights (clips) on blower wheel vanes. Do not drop or bend wheel as balance will be affected.
To reassemble unit, proceed as follows:
1. Place motor with mount attached on flat, horizontal surface with shaft up.
2. Set inlet ring on top of motor mount grommets. Center inlet ring flush on all three grommets.
3. Slide blower wheel onto motor shaft with setscrew upward and aligned with shaft flat portion. Vertically position wheel along shaft to position marked during disassembly.
NOTE: If previous shaft was not marked or if replacing previous motor, set blower wheel position by sliding blower wheel along motor shaft to 1-1/8-in. above rubber grommets (Fig. 26).
4. Hold blower wheel in place and carefully tighten setscrew.
5. Position motor and blower wheel assembly to blower housing as originally oriented.
6. Secure motor mount to blower housing using bolts previously removed.
7. Attach green wire to blower housing with screw.
8. Connect electrical and capacitor leads to original terminals.
9. Replace blower access door and tighten all four screws.
10. Reinsert disconnect pullout only after blower access door is secured. Test blower for proper operation.

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 27

FB4, FE4, FF1E, FFM, FG4, FH4, FJ4, FT4, FV4, FX4, FZ4, PF4, FMA, F54, FY5: Service and Maintenance Instructions

BLOWER WHEEL

11/8

INLET RING

GROMMET

MOTOR

Fig. 26 ­ Motor, Inlet Ring, and Blower Wheel Assembly

A86006

Refrigerant Flow-Control Devices
Thermostatic Expansion Valves (TXV)
NOTE: 2023 models (FE4B, FJ4, F54, FT4) use a mechanical TXV. Refer to the TXV Installation Instructions. Torque the equalizer fitting to 10­20ft-lb; do not exceed 20 ft-lb.
The FE4, FJ4, FT4, FX4, FV4, FF1E, and F54 Fan Coils are factory equipped with a hard shutoff (HSO) TXV. The hard shutoff TXV has no bleed port and allows no bleed-through after system is shutdown.
The TXV is a bi-flow metering device that is used in condensing and heat pump systems to adjust to changing load conditions by maintaining a preset superheat temperature at outlet of evaporator coil. The volume of refrigerant metered through valve seat is dependent upon the following:
1. Superheat temperature sensed by sensing bulb on suction tube at outlet of evaporator coil. As long as this bulb contains some liquid refrigerant, this temperature is converted into pressure pushing downward on the diaphragm, which opens the valve via push rods.
2. The suction pressure at outlet of evaporator coil is transferred via the external equalizer tube to underside of diaphragm.
The bi-flow TXV is used on split system heat pumps. In cooling mode, TXV operates the same as a standard TXV previously explained. However, when system is switched to heating mode of operation, refrigerant flow is reversed.
The bi-flow TXV has an additional internal check valve and tubing. These additions allow refrigerant to bypass TXV when refrigerant flow is reversed with only a 1-psig to 2-psig pressure drop through device.
When heat pump switches to defrost mode, refrigerant flows through a completely open (not throttled) TXV. The bulb senses the residual heat of outlet tube of coil that had been operating in heating mode (about 85° F and 155 psig). This temporary, not-throttled valve decreases indoor pressure drop, which in turn increases refrigerant flow rate, decreases overall defrost time, and enhances defrost efficiency.

4. Large evaporator face area
NOTE: When installing or removing TXV, wrap TXV with a wet cloth. When reattaching TXV, make sure sensing bulb is in good thermal contact with suction tube.
5. The needle valve on pin carrier is spring-loaded, which also exerts pressure on underside of diaphragm via push rods, which closes valve. Therefore, bulb pressure equals evaporator pressure at outlet of coil plus spring pressure. If load increases, temperature increases at bulb, which increases pressure on topside of diaphragm, which pushes pin carrier away from seal, opening valve and increasing flow of refrigerant. The increased refrigerant flow causes increased leaving evaporator pressure which is transferred via the equalizer tube to underside of diaphragm, with which the pin carrier spring pressure closes valve. The refrigerant flow is effectively stabilized to load demand with negligible change in superheat.
Aluminum Coil Unit TXV’s
The distributor used on the all-aluminum coils is also made of aluminum. The TXV connection to the distributor is accomplished with a 3/4″ Chatleff nut (Fig. 27). The threads are coated with Loctite Heavy Duty Anti-Seize which is a graphite/calcium fluoride formulation, for applications that is free from copper, lead and sulfur. This product is typically used in applications with an operating range of -20° F to +2400° F. When replacing a TXV it is recommended to reapply with the same thread sealer.
Extra care should be taken during brazing of copper equalizer on the aluminum coils to prevent the braze material from splattering on the aluminum. Also, route the copper equalizer so that it doesn’t touch the aluminum components.

Problems Affecting TXV

Low Suction Pressure

1. Restriction in TXV

2. Low refrigerant charge

3. Low indoor load

4. Low evaporator airflow

High Suction Pressure

1. Overcharging

2. Sensing bulb not secure to vapor tube

3. High indoor load

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. 28

FB4, FE4

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>