BYVCAS DB600 2 In 1 Dual Action Device Dog Training Bark Collar User Guide

BYVCAS DB600 2 In 1 Dual Action Device Dog Training Bark Collar

EASY RIGHT OUT OF THE BOX

USE THE REMOTE TRAINING MODE

1. Press the button on the collar once to turn it on, you will hear a short VIBRATE to confirm it has been turned on.

2. Make sure the toggle switch on the left of remote on the CHANNEL 1 position and another toggle switch on the CHANNEL R position.

3. Press the button to verify that the remote training mode is working. and the LCD screen shows like this:
   NOTE: Put the test light (clear plastic) on the contact points of collar to testing shock mode.

4. Push down the intensity dial first to activate the ability to change. you will see the or icon flash If the flash, push down again change to ( intensity). Rotate the intensity dial left to + intensity or rotate right to – intensity for the vibrate or and shock.
   (NOTE: SAME THING FOR AUTO BARK MODE)

USE THE AUTO BARK MODE

1. Change the toggle switch to Channel A, It is anti bark mode now. and the LCD screen shows:

2. Follow the STEP 4 to adjust the Intensity of Vibrate and Shock. You will SET the intensity of Vibrate and Shock to 0 both first. the collar will BEEP only when the dog barks. If it can’t make the dog stop bark. increase intensity of Vibrate or and Shock. the collar will BEEP then VIBRATE OR SHOCK OR VIBRATE AND SHOCK base your SETTING to make the dog stop barking.

3. Press the button on the collar less then 3 seconds to adjust the sensitivity level.

   • One Beep = Level 1
   • Two Beeps = Level 2
   • Three Beeps = Level 3
   • Four Beeps = Level 4
   • A Long Beep = Level 5

• You need to find out the right sensitivity level to fit your dog barks and reduce false trigger. THIS IS VERY IMPORTANT!!!
• Level 5 is highest sensitive and easy trigger to work. sometime the collar might work even your dog no barks. (such like other dogs barking around your dog, the collar on the table and your dog barks or high DB voice etc).
• Factory default settings level 4, put the collar under dog’s neck on the throat and enough space to fit one finger snugly in between the collar strap and the dog’s skin. both contact points touch your dog’s neck skin. NO TOUCH NO WORK!!! (Long hair dog have to smooth out his fur around his neck.)
• Awaiting your dog is barking to confirm the anti bark mode is working. If working and more false trigger on this level, set to the level 3 to test again. you can also put the collar under your throat and touch your neck skin, a loud saying “Wu…” to testing.

OVERVIEW

REMOTE CONTROL

LCD SCREEN

• Remote LED Indicator Light Above
  Flashing when you adjust the intensity level for vibrate or shock.

• Remote LED Indicator Light Below

  • It will stay on when the remote is recharging or press buttons on the remote…
  • It will turn off when the battery is fully charged.

AUTO BARK COLLAR

WHAT THE BUTTON USE FOR

• Click the button on the collar once to turn it ON. You will feel a short vibrate to confirm it has been turned ON.
• Double click the button on the collar quickly to turn the collar OFF,
• You will feel a long vibrate to confirm it has been turned OFF.
• Hold the button for 3 seconds into the 10 seconds Pairing status.
  Hold the button less than 3 seconds to adjustable the sensitivity level when use on Auto Bark Mode.

Auto Bark Collar LED Indicator Light

• Pairing: Quick flashing during the 10 seconds pairing process.
• Working: Turns on when the collar is in use or when a mode on the remote is activated.
• Standby: Blink every 3 seconds during standby until no operations have been completed for 5 min.
• Needs Charging: Blink twice per second when charging is needed. It will turn on during charging and when the battery fully charged

PAIRING THE COLLAR REMOTE

1. Press and hold the button on the collar down for 3 seconds. You will hear a short beep from the collar and the LED light will flash green to confirm it is in pairing status.
2. Press the button on the remote within 10 seconds, you will hear a long beep from the collar, this confirms the pairing is complete.
   • (Make sure the toggle switch on the left on Channel 1 or Channel 2 position.)
   • You can’t pairing the collar with remote when the toggle switch on Channel A position.

3. Push down the Intensity Dial first to activate the ability to change. and then Clockwise + intensity or counterclockwise – intensity for the    or . the BEEP Mode is non-adjustable level.
   NOTE: You can also press the Vibrate or Shock button to activate the ability to change when use the AUTO BARK MODE.

4. Press the button to verify that the remote training mode is working. Put the test light (clear plastic) on the contact points of collar to testing shock mode.

   • If you testing with your hand, make sure touch both contact points to feel the shock intensity.
   • It is not recommended to use the shock function excessively to punish your dog and cause psychological damage.
   • If you want to pair another collar to the same remote, Change the toggle switch to CHANNEL 2 and follow the Step 1 to 3 pairing your 2rd collar.

FIT THE COLLAR ON YOUR DOG

• The collar size is adjustable to fit your dog’s neck between 9″ and 26″ If your dog’s neck circumference is smaller than 9″ or larger than 26″ the collar will not be suitable. Moreover, the collar should not be worn by dogs under 10 pounds.
• A well-fitted collar is essential for ensuring that the two contact points press firmly against the dog’s skin, which will foster training efficiency and quality.

CORRECT WEAR THE COLLAR:

• Collar under dog’s neck on the throat.
• Both of contact points touch the neck skin.
• Enough space to fit one finger snugly in betweenthe collar strap and the dog’s skin.

CUT THE EXCESSIVE COLLAR STRAP
When you adjust the collar to fit your dog’s neck there was an excessive amount hanging over it you want to cut the excessive amount off. Please burn the end of the collar to prevent the whole thing frayed.
IMPORTANT: Do not wear the collar on your dog over 12 hours per day. and you have to check your dog’s neck every day, may cause skin damage. Ranging from redness to pressure ulcers; this condition is commonly known, as bed sores.

RESPONDING RANGE

• The dog collar has a responding range of approximately 1,300 feet, which may slightly vary depending on the way the remote is held. Hold the remote out and away from your body to maintain an ideal range.
• When holding the remote, please do not touch or block the antenna to avoid a potential sharp decrease in the responding range. To ensure strong signals and connections, make sure the device is sufficiently charged before each use. Range will not be limited through glass windows, but it will be limited through a door or wall.
• The 1,300 feet range was designed and tested for flat terrain. Trying to use the remote through bushes, trees, hills, buildings, and or moisture can make a difference to the range. To keep possession of an ideal range, please hold and lift the remote above your head when the dog is far away or tries moving to higher ground.
• Any electrical conductors such as cars, chain-link dog runs, metal buildings, and radio towers will also affect the range. For the best effect, please approach such devices as few as possible during the training.

WATERPROOF THE COLLAR

• To ensure the collar is 100% waterproof, make sure the rubber cover on the USB charging port on the back of the collar is fully sealed.
• Sometimes we forget to fully seal rubber cover on the charging port after the collar has been fully charged. Which can make the collar not waterproof.
  Keep the rubber cover fully sealed to ensure a long lifespan!

ONE YEAR WARRANTY

We offer a 1-YEAR warranty starting from the purchase date. our product has undergone a thorough quality inspection at the factory to ensure that it is in good condition. If any defects in workmanship or materials within the warranty period, we will promptly provide a remedy.

CONTACT THE CUSTOMERS SERVICE
If you have any questions regarding installations, using the product, or any other related issues, contact us through one of those methods.

1. Please go to “My orders > Find Order > Contact Seller”
2. Go to the product page, you will see a line said “Sold by ‘store name’ and Fulfilled by Amazon”. Click”store name” > Have a question for ‘store name’ – “Ask a question”

WARNING
Please Set To The Right Sensitivity Level To Use The Auto Bark Mode

• We have used a new technology to identify the barks from your dog by Vibration and trigger the collar work. So you need to make sure both contact points touch your dog’s neck skin. Eough space to fit one finger snugly in between the collar strap and the dog’s skin.
  NO TOUCH, NO WORK!!!
  (Long hair dog have to smooth out his fur around his neck.)

• Level 5 is for testing. sometimes you will gets more false trigger even your dog no barks. (such like other dogs barking around your dog, your dog just shake his head, tickle his neck, a baby crying or kids laughing around him, high DB voice etc).

• It is easy to work when the collar on the Wooden Table or Glass Table.

• This false trigger caused by external sound conduction resonance.

• Set the sensitivity level to level 4 first, let your dog is barking to confirm the anti bark mode is working. testing the false trigger on this level, if gets more false trigger, set to the level 3 and test again.

• If the level you set easy to work when your dog barks and have no more false trigger, it is right sensitivity level for your dog barks. you can also put the collar under your throat and touch your neck skin, a loud saying “Wu…..” to testing.

ENSURING YOUR DOG’S SAFETY

• Do not attach a leash to this collar; It can result in severe injury by pushing the contact points too tightly against a dog’s neck.
• Do not wear the collar too tightly, as it may cause neck’s skin damage;
  • Do not keep the collar on your dog over 12 hours per day;
  • If possible, reposition the collar on the dog’s neck every 2 hours.
  • Please check your dog’s skin everyday to avoid ranging from redness to pressure ulcers (commonly known as bed sores).
• Keep charge the collar per 30 day to extend the battery life if not use.
• Keep the collar out of reach of dog. they always chewing the collar.
• Do not use this collar if your dog is aggressive, or if your dog is prone to aggressive behavior. If you unsure whether this collar is appropriate for your dog, please consult your veterinarian or certified trainer.

WHY THE ITEM LOOKS LIKE OLD OR SECOND-HAND

We believe that this item may have returned by a previous Amazon buyers. And because the retail box was intact, Amazon did not check the contents of the box. If you receive an item that appears to be old or second-hand, with dog hair, an odor of dog, or missing accessories, please contact us through your order OR our Customer Service email to gets after-sales service or a refund.

WHY DOES THE DOG’S NECK BECOME RED AND IRRITATED

• This condition is due to the Contact Points irritating the skin. Discontinue use of the collar receiver for a few days.
• These collars can cause pressure necrosis if use incorrectly and is OFTEN MISIDENTIFIED AS BURNS.
• To protect your dog and avoid this condition on your dog. You need:
  • Do not wear the collar on your dog over 12 hours per day;
  • Please check your dog’s skin everyday to avoid ranging from
  • redness to pressure ulcers (commonly known as bed sores).
  • Do not make the collar too tight and make sure enough space to
  • fit one finger snugly in between the collar strap and dog’s skin.
  • Do not use the SHOCK function excessively to punish your dog often.
  • Ensure the contact points touch your dog’s neck skin both when use the SHOCK function.

WHY THE SHOCK DOES NOT WORK

• Make sure the toggle switch not on position to LOCK ALL MODES,
• Make sure the intensity of shock not to be 0 and the Dog Channel you was paired before.
• Make sure the contact points touch your dog’s neck skin both. NO TOUCH NO SHOCK
• If you testing with your hand, touch both of contact points to feel the shock intensity.
• If you done all of the above, CONTACT US by SERVICE MAIL.

WHY THE AUTO BARK MODE DOESN’T WORK

1. Make sure the collar can use in the remote training mode.
2. Make sure the toggle switch on Channel A position.
3. Scratching or blowing the collar is wrong test way for our collar.
4. Put the collar under your throat and touch your neck skin, a loud saying “Wu…” to testing. If work, follow next steps find the issue.
5. It doesn’t work on the dog’s back when the dog barks.
6. Make sure the collar under dog’s neck on the throat, Enough space to fit one finger snugly in between the collar strap and the dog’s skin.
7. Long hair will be effect the Contact Points touch dog’s neck skin. you have to smooth out his fur around his neck.
8. Both of (metal probes) contact points touch the neck skin. NO TOUCH, NO WORK!
9. Maybe the sensitivity level is low and your dog barks can’t trigger to work, Press the sensitivity button to adjust sensitivity level to fit your dog barks. level 5 is easy to work and gets more false trigger.
   • One Beep = Level 1
   • Two Beeps = Level 2 Three Beeps = Level 3
   • Four Beeps = Level 4 A Long Beep = Level 5
10. The collar power off, charging the collar for 2 hours.
11. If you done all of the above, CONTACT US by SERVICE MAIL.

WHY THE AUTO BARK MODE WORK EVEN MY DOG NO BARKS

• We have used a new technology to identify the barks from your dog by Vibration and trigger the collar work. So you need to make sure both contact points touch your dog’s neck skin. Eough space to fit one finger snugly in between the collar strap and the dog’s skin. NO TOUCH, NO WORK!!!
  (Long hair dog have to smooth out his fur around his neck.)

• Level 5 is for testing. sometimes you will gets more false trigger even your dog no barks. (such like other dogs barking around your dog, your dog just shake his head, tickle his neck, a baby crying or kids laughing around him, high DB voice etc).

• It is easy to work when the collar on the Wooden Table or Glass Table.

• This false trigger caused by external sound conduction resonance. Set the sensitivity level to level 4 first, let your dog is barking to confirm the anti bark mode is working. testing the false trigger on this level, if gets more false trigger, set to the level 3 and test again.

• If the level you set easy to work when your dog barks and have no more false trigger, it is right sensitivity level for your dog barks. you can also put the collar under your throat and touch your neck skin, a loud saying “Wu…” to testing.

IT IS NOT WATERPROOF ANYMORE

• The collar works properly a few days or more and then completely stopped working.
• The collar constantly turns off, even after being fully charged. and doesn’t turn off properly.
• Nothing happens when you press the buttons or try to charge it.
• Sometime we forget to fully seal the rubber cover on the charging port after the collar has been fully charged, which can make the collar not waterproof.
• If water gets into the collar and the collar started going off randomly beeping, vibrating for no reason. remove the collar from your dog, unscrew the screws, wipe out the water stains on the circuit board and the shell. Wait for it to dry, then re-install it and try again.
• To ensure the collar is 100% waterproof and has a longer lifespan, make sure to fully seal the rubber cover

WHY CAN’T THE COLLAR BE PAIRED

• Please charging the collar and remote for 3-5 minutes first.
• If nothing happens, use other 5V USB cable charging them, it you can charging them, which means the issue from the USB cable, Please contact us to gets after-sale service.
• If nothing happens, it means that the collar or remote is dead.
• If the charging status is normal but nothing happens when you press the ON/OFF button, it means that you can not charge them any more.
• Please contact us to gets after-sale service.
• If nothing happens when you press the buttons to pair the collar to the remote, it means that the remote is broken, Please contact us to gets after-sale service.

WHY DOES THE LED LIGHT ALWAYS STAY ON AFTER CHARGING

This indicates a problem with be charging mechanism. Please contact us to get after-sales service.

I CAN’T TURN OFF THE COLLAR, THE LED LIGHT FLASH TWICE ALWAYS

• This means the collar is out of power, and the intensity of vibrate or shock not stronger too when you press the buttons, please charge the collar for 2 hours.
• Usually the remote standby about 90 days, the collar standby about 10 to 15 days.

IF THE COLLAR GOES INTO SLEEP MODE, DOES IT TURN BACK ON

• In Auto Bark Mode, the collar will turn back on when the dog starts barking.
• In Remote Training Mode, hold one of mode buttons to turn back on.

WHERE CAN I BUY EXTRA ITEM OR ACCESSORIES FOR REPLACEMENT

Please contact our SERVICE MAIL to know where you can buy them. Sometimes you will get the accessories for free. If send from China, usually you will get it 10-25 days

FAQ

• Why doesn’t the remote work in the responding range or why the connection become weakened when my dog is farther away?
  Check to see if the remote antenna is blocked by fingers or other items, which could decrease the responding range significantly.

• How long should I process each training session for my dog?
  Each training session should be processed as short as about 15 min.

• Can I attach a leash to this collar?
  We strongly suggest that you do NOT attach a leash to this collar. It can result in severe injury by pushing the contact points too tightly against a dog’s neck. If you need to use a leash, attach it to a separate and non- metallic collar or a harness while making sure that the extra collar does not put any pressure on the contact points on the dog collar.

• Are there any minimum age requirements for the dogs using the device?
  There is no limit of ages for dogs using the collar purposes. However, to develop quality training, you should make sure that the dog can comply with basic obedience commands such as “Sit” or “Stay”. Regardless of age, the collar might be too large for dogs under 10 pounds.

• Why doesn’t the device work when I test it with my hand?
  Is the Vibrate/Shock safe for my dog?
  When testing the collar with your hands, touch both electrodes located at the back of the collar at the same time.
  While the Vibrate/Shock is unpleasant, it is harmless to your dog.
  IF YOU CAN’T FOUND THE ANSWER IN THIS GUIDE.
  PLEASE SHOW US YOUR ISSUE IN THE VIDEO. WE WILL TELL YOU HOW TO FIX IT OR SEND A NEW ONE TO YOU FOR REPLACEMENT.
  DON’T WASTE YOUR MONEY, IF YOU’RE IN ONE YEAR WARRANTY

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>