Zhier ZE-CPE1000 Wireless Bridge User Guide

Zhier ZE-CPE1000 Wireless Bridge

Product Information

The product is a wireless bridge that allows for the transmission of data between devices. It consists of two units, A and B, which can be configured in A-B mode to create a network connection. The product also features LED indicators for power, configuration status, and network connection.

Specifications

• LAN1: LAN port for device connection
• LAN2: LAN port for device connection
• PWR LED: Power indicator
• RST: Reset button
• LED A IP: LED indicator for A unit IP address
• LED B IP: LED indicator for B unit IP address
• 2.4 ID: ID number for 2.4 GHz frequency
• 5.8 ID: ID number for 5.8 GHz frequency

Product Usage Instructions

Setting up the Wireless Bridge

1. Set the A-B mode DIP switch on both units to configure them as a pair.
2. After setting the mode, the LED indicator (L) will appear and blink. Wait for the LED indicator to stop blinking to confirm
3. successful configuration.

Configuring IP Addresses

The product allows for the configuration of IP addresses. Each unit (A and B) has a range of pre-configured IP addresses.

LED Indicators and Status Lights

• LED: Indicates the configuration status and network connection.
• RST: Status lights for A and B units.
• 1-5s press: Press the reset button for 1-5 seconds to automatically increase the LED display.
• Press over 10s: Press and hold the reset button for over 10 seconds to perform a system restart.

Network Connection Status

• Link: Indicates the bridge connection status. When connected, the link lights up. When not connected, the link is off.
• LAN1 and LAN2: Indicate the data communication status. When data is being transmitted, the corresponding LED will flash. When there is no data transmission, the LED will be off.

Power Indicator

The power indicator LED shows the power status of the device. It turns on when the device is powered on.

Frequently Asked Questions (FAQ)

Q: How do I configure the wireless bridge units in A-B mode?

A: Set the A-B mode DIP switch on both units to configure them as a pair.

Q: How do I reset the configuration of the wireless bridge?

A: Press and hold the reset button for over 10 seconds to perform a system restart.

Q: How do I know if the network connection between the units is successful?

A: When the A and B units are successfully connected, the LED display will show a constant number (not flashing).

Wireless Bridge

1. First Set A B A-B mode DIP switch, led L appears and blinks. After the disappearance of L, an arrangement remains successful.
2. The reset button to set the LED digital display, click the startup configuration status, then click the automatic increase. Can be continuously increased
3. Assume that a pair of bridges with a number of 1 is configured After A set to 1, after B is set to 1, the LED will flash, L application configuration appears blinking, wait, L foot after flashing into a digital 1, 1 will continue to flash until the A, and B are connected After the success, the LED display 1 is always on, not flashing, indicating that the AB has been successfully networked.

Link|

The bridge connection is successful, link lights, are not connected Off

---|---
LAN1|

Turning on the lighting data, the communication flashing, off data nowhere

LAN2|

Turning on the lighting data, the communication flashing, off data nowhere

PWR| Power indicator, power on
LED| Display H, expressed configured to manually set state
LED| L displayed and flashes represent settings
LED| Flashing, it indicates to modification of the configuration or is connected to the
Round light| A, B status lights, light that is not mode A, mode B light that
RST| 1-5s press, led the digital automatic increase, 0-F from circulation
RST| Press over 10s, release the reset, and the system automatically restarts
LED| A IP| B IP| 2.4 ID| 5.8 ID
---|---|---|---|---
0| 192.168.255.100| 192.168.255.200| 0| 0
1| 192.168.255.101| 192.168.255.201| 1| 165
2| 192.168.255.102| 192.168.255.202| 2| 161
3| 192.168.255.103| 192.168.255.203| 3| 157
4| 192.168.255.104| 192.168.255.204| 4| 153
5| 192.168.255.106| 192.168.255.205| 5| 149
6| 192.168.255.106| 192.168.255.206| 6| 48
7| 192.168.255.107| 192.168.255.207| 7| 44
8| 192.168.255.108| 192.168.255.208| 8| 40
9| 192.168.255.109| 192.168.255.209| 9| 36
a| 192.168.255.110|

192.168.255.210

| 10| 140
b| 192.168.255.111| 192.168.255.211| 11| 132
C| 192.168.255.112| 192.168.255.212| 13| 124
D| 192.168.255.113| 192.168.255.213| 96| 116
E| 192.168.255.114| 192.168.255.214| 50| 108
F| 192.168.255.115| 192.168.255.215| 55| 100

The Building Diagram is as follows

Bridge settings: POE port connects to the bridge LAN1 (near reset button) power supply. LAN port connected to the computer network port.

Landing

After power-on, Connect the device LAN2 port to the PC network port, Add IP address and subnet mask of 192.168.255. segment in PC

Open your browser, and input the login IP address of the device (if the device is A  enter: http: //192.168.255.1; if the device is a B Enter http://192.168.255.2) and press Enter for login WEB Management interface.
In order to ensure the best display for WEB. Make sure to use the latest version

A device configuration

1. Enter the interface of [Bridge Set]
2. Bridge mode is set to mode A
3. Set the ID number (The ID number of device A is the same as pairing device B)
4. After Press the [Application settings] Buttom the configuration is effective

B device configuration

1. Enter the interface of [Bridge Set]
2. Bridge mode is set to mode B
3. Set the ID number (The ID number of device B is the same of pairing device A)
4. After Press the [Application settings] the configuration is effective

Note:

1. For One-to-many Setting. The ID number must be the same for A device and more devices B
2. For more “One-to-many Setting” Keep the ID numbers different, and for this Avoid connecting to each other.
3. In the login window to enter a user name and password (the default are both: admin), and press the “OK” button.
4. After successful login into the bridge configuration interface

Using schematic

1. One to One is used for connection between two devices.
2. Onet to More is used for connection between One device A and more devices

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment protein aged an on-screen with a resident installation This equipment generates uses and a salute The frequency energy and, notisansand use
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. RF Exposure Statement
   To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>