MAGICFX MFX3225 SFX Safety Combiner Box Instruction Manual
- May 16, 2024
- MAGICFX
Table of Contents
MAGICFX MFX3225 SFX Safety Combiner Box
INTRODUCTION
This manual contains all information required for the intended use of the equipment. Deviation from the described intended use can result in a hazardous situation and/or property damage.
DESCRIPTION
| Product code | MFX3225 | Size (LxWxH) | 15 x 3.5 x 13.5 cm |
|---|---|---|---|
| Voltage | 100 – 250 Vac | Weight | 1.6 kg |
| 50 / 60 Hz | Mounting options | M10 insert | |
| Power consumption | 50 W | Power connector | Neutrik® powerCON TRUE1 |
(in)
Protection| Rainproof| ARM / DMX+ARM
connector
| Neutrik® etherCON, RJ45 (in&out)
Technical data
The COMBINER BOX is a splitter and booster device for the safety signal of the ARM SYSTEM. The COMBINER BOX acts as a slave of the connected ARM CONTROLLER, which is the master of the safety line. The COMBINER BOX is also capable of combining the ARM signal input with a DMX signal, into a DMX+ARM output. Furthermore, it provides a boosted output signal to overcome signal loss over long cable runs.
For more information about the ARM SYSTEM and to learn how to configure a complete safety system, refer to the ARM SYSTEM Configuration Manual (PART02323). For more information about the ARM CONTROLLER and to learn how to correctly set up and use the ARM SYSTEM, refer to the ARM CONTROLLER User and Installation Manual (PART01882).
| Main parts | ||
|---|---|---|
| **** | **** | **** |
| LED indicator | Light | Meaning |
| ARM signal LED | Off | The system is disarmed: The SFX machines cannot be |
operated.
| Red| The system is armed: The SFX machines can be operated normally.
| Red
flashing
| The emergency stop button is actuated or a line interruption outside of the
controller is detected. The output of the SFX machines is disabled.
DMX signal LED| Green| The COMBINER BOX is receiving a DMX signal.
Power LED| Blue| The COMBINER BOX is connected to a power supply.
| | LED indicators
INSTALLATION
WARNING
Make sure that you are familiar with and comply with the instructions from
the user and installation manuals of each relevant ARM SYSTEM component and
each connected SFX machine.
NOTICE
Insert a TERMINATOR in the last ARM output of each master and each slave
line to close the safety circuit. The ARM SYSTEM will not work when a line
remains open. Install the COMBINER BOX in the ARM safety circuit and connect
the COMBINER BOX to a power source. Check the following installation variants
for connection details. Use the COMBINER BOX to split the ARM signal into a
master line and a slave line. The slave signal is also boosted in this setup.
Use a dedicated COMBINER BOX to boost the ARM signal.
Use the COMBINER BOX to combine the DMX signal and the ARM signal.
SOFTWARE SETTINGS
Make sure that the DMX/RDM settings on each SFX machine match your wiring setup. If the DMX signal runs separately over 5-pole XLR cables, make sure that XLR is selected as DMX INPUT in the menu. If a combined DMX and ARM signal runs over the ARM data (EtherCON) cables, make sure that ARM is selected as DMX INPUT in the menu.
CORRECT DISPOSAL
This symbol on the product and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery, and recycling, please take this product to designated collection points where it will be accepted free of charge. Alternatively, in some countries, you may be able to return your products to your local retailer upon purchase of an equivalent new product.
Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest designated collection point. Penalties may be applicable for incorrect disposal of this waste, per your national legislation.