EASESUPER T601P-W-Y Rv Tire Pressure Monitoring System User Manual

EASESUPER T601P-W-Y Rv Tire Pressure Monitoring System

Quick explanation

Caution : Turn on the power of the display and then install the sensor. Follow this step, and the data can be displayed at real time.

Product features

• The monitor keeps sleeping mode after parking for three minutes and receive the data in real time until shocked again
• Large display
• High efficiency solar charging
• Monitor: Automatically wake-up
• Two grades backlight brightness
• 7 kinds of alarming modes :high / low pressure /high temperature/Sensor failure/Monitor low power/Sensor low power /Rapid air leak alarm
• Pressure units (PSI, BAR) and temperature units (* F/° C)
• Long receiving distance
• Monitor up to 6 types
• Two alxes high and low pressure values setting

Package contents

• Monitor (1)
• Mat(1)
• Anti theft ring (7)
• Signal booster(optional) Sensors (6)
• Instructions (1)
• USB charging cable (1)
• Battery wrench(1)

Functional description of the display

After the display alarms, press anywhere on the display to remove the prompt sound, and the flickering prompt will continue till the fault is removed

• Factory default settings
• High pressure alarm value :116PS
• Low pressure alarm value :58PS
• High temperature alarm value :149°F

How to restore the factory defult?
Turn the monitor off, then turn it on and holding press the SET button until hearing the sound of “D…”. The standby interface will be displayed, indicating that the factory reset successfully.

High-pressure alarm

Tire pressure is over 116PSI

Low-pressure alarm

Tire pressure is lower than 58PSI

1. The symbol means flickering and will not appear on display actually.
2. It’s common with + / – 2psi deviation, which will not affect your judgment whether tires are in good condition or not

Tire-temperature alarm ire temperature is over 149 °F

Air-leaking alarm

Functional description of the display

Sensor Low-power alarm Low-power prompt of sensor

Note: when the sensor gives a low-power alarm, the low-power icon and the pressure value are displayed alternately, Lo is displayed for 10 seconds, and the pressure value is displayed for 30 seconds. Cycle alternately until the exception is removed.

Sensor failure

• Sensor failure prompt, for example: No.1 Sensor failure, alarming as below

Monitor low battery alarm Low-power prompt of Monitor

Please use USB cable to charge for the monitor by vehicle power supply. Avoid charring at a long time parking.

Parameter setting

Detail of display

• The tires in monitor interface are divided into two axles as follows
• The tire numbers(01.02,03,04,05,06) represent the tire position where the sensor is located.

NO.5,6 Sensors can be used on tires of your trailer

(The parameters have been set before delivery, and the operations below are not needed)

Setting of unit of pressure

Caution

• Maximum pressure can be set to 199PSI (13.7 BAR)
• Maximum alarm value can be set to 199 PSI (13.7 BAR)

Setting of unit of temperature

Setting of upper alarm value of First axle tire pressure

• Caution: Maximum alarm value can be set to 199 PSI (13.7 BAR)

Setting of upper alarm value of Second axle tire pressure

Caution : Maximum pressure can be set to 199PSI (13.7 BAR)

Setting of lower alarm value of First axle tire pressure

Parameter setting

Setting of lower alarm value of Second axle tire pressure

Setting of upper alarm value of tire temperature

Interchange tire setting

4 or 6 tires option

Repeater installation

Repeater: Optional, strengthen the signal (We suggest to install the repeater to near by the head of vehicle.)

Repeater can make sure to strengthen the signal within 30m.Red cable connects with the anode of the battery, and the black cable connects with the cathode. The button on repeater flash with red light means it is working normally. Otherwise, you need to confirm whether the repeater is properly connected. Or it may be broken if still not flash.

Matching operations

Note : The operations have been matched before delivery, and they are only needed when the data is missing, or when the sensor or the display needs to be replaced.

Matching of outer sensor

Matching of outer sensor

Note : Don’t need matching until it lose the link due to interference or replacement

Installation of sensor

Installation of outer sensor

1. First tighten the anti-burglary gasket and the tighten the sensor
2. Hold the anti-burglary gasket with a spanner and tighten it counter-clockwise

1. First tighten the anti-burglary gasket and then tighten the sensor
2. Hold the anti-burglary gasket with a spanner and tighten it counter-clockwise

Replace sensor battery

1. Remove the tamper ring.
2. Open the housing with a spanner and remove it Replace the battery.

1. Remove the tamper ring.
2. Open the case and remove and replace the battery.

Trouble-shooting

1. The display cannot be displayed normally

   • Confirm if the display is short of power or not (charge directly if so)
   • Confirm if the display cannot display tire pressure value

2. The sensor is short of power, 2. The signal is interfered, then match again)

   • Confirm if the display is short of codes (low-temperature cooling)
   • If the display is halted and displays in full screen (contact and return to the manufacturer or stay for 24 hours till it is recovered automatically)
   • If the above methods cannot solve this problem yet, contact the local distributor.
   • The sensor cannot work normally
   • Confirm if the sensor is short of power (replace the battery in time)
   • In case of an outer sensor, replace with a CR1225 button cell in time
   • In case of a common outer sensor, replace with a CR1632 button cell in time
   • In case of an inner sensor, contact the distributor and return it to the manufacturer.
   • Confirm if the sensor is damaged due to external force (purchase another one and replace ii)
   • Confirm that the normal work of the sensor and the vehicle is not affected in driving after the sensor is installed (potential risk! Too close distance between the air nozzle and the clip may result in the damage)
   • The sensor cannot be installed normally in case of a special vehicle during installation (contact the technical personnel of the manufacturer and seek for the solution).
   • If the problem cannot be solved with the above methods, contact the local distributor.

3. When the icon of “short of power” appears on the display screen, and it continues being used, the display may be malfunctioned. At this time, charge the display to return it to normal.

4. The colors of the display screen are changed Confirm if the temperature inside the vehicle is too high (over 65°C).
   When the temperature returns to normal, ii will be recovered to nonnal display.

5. Update speed of the display screen becomes slower
   Confirm if the temperature inside the vehicle is too low (below -20°C).
   When the temperature retums to normal, it will be recovered to nonnal display.

6. After the display is started again, there’s no data display of tires

7. Only when the sensor detects that the tire has a pressure change of over 1 PSI, it will send new pressure and temperature value to the display, so there’s no data display of the tire. The data will be displayed only after the vehicle is started.

Two years warranty

matters needing attention

• Please use the product in accordance with the operating instructions.

• The factory will not bear any responsibility for the consequences caused by misuse beyond the operating instructions.

• Please install the product in accordance with the operating instructions. The factory is not responsible for any consequences caused by incorrect installation in accordance with the

• operating instructions.

• Please set the alarm threshold according to the specifications and parameters provided by the tire manufacturer and its dealers.

• TPMS factory is not responsible for the consequences caused by
  any error in setting the alarm threshold.

  • TPMS installation must be handled by technicians. During use, care should be taken to maintain the sensors in the tires and remove / load the tires.
  • This instruction manual is subject to change without notice if necessary.

Parameters of sensor

Notes for attention and statement

• This product applies only to the models of cars with air pressure of lire within 199PSI.
• The safety of Car tires cannot be wholly dependent on this product. The tires shall be checked on a regular basis, and the tiresshall be ensured to be free from damages such as pricked hole.cutting and swelling.
• When the product gives out an alarm, the driver shall stop the car for checking and handling.
• The product cannot forecast any sudden damage of the tires as a result of external force.
• Do not operate the product in driving.
• The shelf life of the battery of the sensor is related to the driving mileage of the Car.
• Do not charge the monitor for a long time (to avoid shortening the battery life of the monitor).
• Please don’t use the liquid tire repair agent.or it may block the sensor detection hole.

Notes for use
Please read the following carefully before installing the product:

1. The display shall be installed at the place where driving view is not blocked.

2. The display shall be ensured to be reinforced so that it will not fall off in the course of driving.

3. After the sensor is installed, confirm if the air nozzle is air leaking, and apply some soap water at the air nozzle when necessary and check if any air
   leaking exists.

4. When the air pressure is too high, take care and prevent the lire from bursting in driving, and when the air pressure is too low, take care of oil consumption and balance.

5. The product can monitor the tires at real time effectively, but it cannot guarantee any sudden occurrence of safety accident of tires. Therefore, choosing tires of good quality is of equal importance with ensuring normal air pressure of tires.

6. When the vehicle is in driving, if the signal is interfered, the signal of the display may be missing, and the use of the product may be affected. In this case, it shall be matched again.

7. lf the display is not touched or vibrated within 3-5 minutes, ii will hibernate automatically, and a slight vibration may trigger automatic power-on test of the data transmitted by the sensor.

8. The connection between the display and the sensor is wireless. Several
   anti-interference functions have been designed and the possibility of its being interfered is extremely low.

9. ln the course of driving, due to thermal expansion and contraction, air pre ssure of tires may be changed towards slightly low or slightly high, and it’s normal.

10. .Generally, natural air leaking of the tires may occur due to natural ageing of rubber product, and it’s normal and has not direct relationship with installation of the product.

11. prohibited to dismantle, modify or change the product by yourself, and it’s the responsibility of your own in case of your doing so which results in failure of normal work of the product.

12. The original air nozzle of the vehicle being rubber one, it’s recommended be changed into an aluminum alloy one (for when the sensor is mounted onto the rubber air nozzle, the air nozzle may fly out due to the impact of centrifugal force at high-speed rotation).

13. The specification and technical parameters may be inconsistent with those in the user manual, for they may be changed from time to time due to upgrade or update. They are subject to the actual product without prior notice, and the manufacturer reserves the right to interpret them.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>