DVKNM IP69 LCD Monitor Back Camera Instruction Manual
- June 15, 2024
- DVKNM
Table of Contents
Backup Camera and 9-inch LCD Monitor
Kit-User Manual & Installation instructions
IP69 LCD Monitor Back Camera
The Protective Film
There is a protective film on the screen, which protects the screen during
shipping. If it is scratched, you can replace one before using.
Tear off The Film
The film can be teared it off by the small white tape on the corner.
If it is stuck, please use your nail to make a small gap between the frame and
the screen, then use another hand to tear the film off.
DURING THE WARRANTY PERIOD, SHOULD YOUR REAR VIEW SAFETY PRODUCT EXHIBIT A
DEFECT IN MATERIAL OR WORKMANSHIP, PLEASE CONTACT US FOR REPLACEMENT.
What you get
1 9 inch Monitor
4 Cameras
1 Power Cord
1 Mounting Bracket
2 10M Cable
2 20M Cable
1* Remote Control(Require a CR2025 button battery, not include)
Wiring
The package include 4 cameras and 4 extension cable (210m, 220m). The install is very easy, please reference the below wiring diagram.
Wiring Direction
The monitor has six color cables(Red/black/blue/white/green/brown ). The red
wire connected to positive 12V/24V, black wire to ground. If you use one
camera as a backup camera, Connect the corresponding color cable to 12V/24V
positive power accordingly [ Blue-CH1, WhiteCH2, Green- CH3, Brown -CH4 ].
eg: If the blue wire is connected to backup light positive, when you turn to
reverse gear, the monitor will automatically show the backup image( CH1). When
the reversing finished, the monitor will return to original video showing
mode.
Kindly note: The 4 colors cables ( blue/white/green/brown ) could not
connected meanwhile, you only need to connect one of them if you choose one
camera as a reversing camera.
Tips:
- The connector is pins type, please be careful connect it correct and tightly. Every connector has interface mark.
- If you have any confusion or problem after installation, please contact us first, we will try our best to serve you.
Remote Control
- Mode election
- Power button—–Power on/off
- Up selection
- Left selection
- Menu—–Set language/guide line/Contrast/Bright/Image flip etc.
- Right selection
- Down selection
- CH1—–Switch to camera 1
- CH2—–Switch to camera 2
- CH3—–Switch to camera 3
- CH4—–Switch to camera 4
Menu Settings—–Switch Cameras/language/Guide line/Contrast/Bright/Image
flip
4.1 Switch Cameras/Split Screen
Press CH1/CH2/CH3/CH4 to switch cameras, you also can press” MODE” button to
set to full/split/three/four screen.
4.2 Language
Press “menu” button⑤ on remote, then press “menu” two times, press button ⑥ to
set languages.
4.3 Guide line
Press “menu” button⑤ on remote, then press “menu” one more time and press
button ⑥ four times to turn on/off guide line.
4.4 Contrast/Bright
Press “menu” button⑤ on remote, then press button ⑥ to set brightness
Press “menu” button⑤ on remote, then press button ⑥ two times to set contrast
4.5 Image flip
Press “menu” button⑤ on remote, then press “menu” one more time and press
button ⑥ to turn on/off guide line.
Note: If you want to flip all 4 cameras together, you can switch to four split screen, then choose “ROTATE”.
Troubleshooting
5.1 One camera not work
Please check if the extension cable and connector is good or not, you can test
with other cameras’ cable.
If still not work, please contact us for free replacement.
5.2 Monitor not turn on
a. After connecting to power DC 12V-24V, is the screen black or blue?
– If the screen is black, the screen can’t get powered
Please check if the fuse or power connection is good, and if the power voltage
is constant DC 12V-24V.
– You can also do a test, remove the screen from the car, connect the screen
directly to a battery, red positive and black negative. See if it can turn on.
– If the screen is blue, showing character ”CH1-CH4”, the screen is good.
Please check the camera connection, also you can test if the extension cable
is good by removing it and connecting the camera and monitor together.
b. You can test cameras with another monitor.
5.3 Can’t switch channels when reversing, need to use remote control
If you want to view single camera image when reversing (reverse propriority
function), only want to switch channel sometimes, you can switch it by the
remote, instead on the monitor button.
5.4 Not connect the reversing trigger line
If you want to view all channels all the time, please don’t connect the
trigger cables (blue, brown, white and green cables on screen harness).
Then when you are reversing, it will not show single image automatically.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>