CHOICE SUPPLIES Yukon Toilet Suite Instruction Manual
- June 4, 2024
- CHOICE SUPPLIES
Table of Contents
CHOICE SUPPLIES Yukon Toilet Suite
Features
- Product Code – 131150313 Labour Warranty – 1 Year Ceramic Warranty – 5 Years S-Trap – 60 – 180mm
- P-Trap – 180mm
- Soft Close / Quick Release Seat
Dimension
Dimensions are approximate. The information provided in this brochure is representative of the actual products available at the time of printing. Due to our policy of continuous product development, the designs and specifications depicted are subject to change without notice. Please confirm all particulars with your consultant prior to purchase. Each product is covered by a limited warranty. Full terms and conditions are available from your sales consultant.
INSTALLATION
Note: All measurements for roughing-in should be taken from the finished wall/floor. Installation of this product is to be performed by a licensed plumber.
-
Rough in the position of water inlet, and waste outlet. Ensure the inlet connection extends 60mm from the finished wall. Pan fixing brackets are provided as an optional extra fixing (see step 7), drill holes into the floor now if required.
-
Lubricate the fins of the pan bend and position them into the waste pipe.
-
S-Trap: Lubricate rubber on the exposed connector end
-
Align and push the pan back onto the wall
-
P-Trap: Set up the waste pipe so that the end of the pan collar extends 260mm from the finished wall.
-
Align and push the pan back to the wall, connecting the pan spigot to the pan collar. Bucket flush and check for leaks.
-
Place rubber seal into pan recess. ( DO NOT USE SEALANT). Place cistern screws into holes on the inside of the cistern, making sure the washers are located correctly. Gently lower cistern onto pan locating fixing screws into matching pan screw holes. Secure cistern to pan. Before tightening fully, make sure the system sits square and straight to the pan. Connect pan fixing to brackets if installed at step 1. Due to the design, weight, and stability of the pan and cistern a silicone adhesive only is recommended and excepted by the manufacturer for floor-based fixing.
-
IF BACK INLET, SKIP THIS STEP: Remove the cap from system plug A or B at the base cistern. flexible hose to cistern plug A or B depending on the location of the stop tap. Complete stop tap connection to the underside of system plug C or D. Fill System and ensure correct water level. Connect
Note: Inlet valve can be adjusted if required. -
IF STEP8IS COMPLETED, SKIP THIS STEP. Fit off stop tap then connect the rear water inlet valve to stop tap. Fill system and ensure the correct water level
-
Make sure the inlet vale flow is free from the side of the cistern wall If the inlet vale is jammed on the system wall, it will cause the inlet valve to keep filling. Installation of the Toilet seat and Cleaning t is recommended that the toilet seat and cover be installed after all trades are finished
Cleaning Recommendations
The high-quality vitreous china finish on all sanitary ware can be maintained by simply using mild soapy water and wiping it over. Sanitary ware should not be cleaned with abrasive materials e.g. steel wool/scourers. Do not use any corrosive or abrasive cleaning agents containing acids or scouring agents as this may lead to surface damage. Bleaches can also discolor seats and hinges and therefore should not be used. If your toilet has metal hinges they should only be cleaned with a mild liquid domestic cleaner, with soft soapsuds, or Steel & Chrome cleaner. After cleaning, rinse with clean water and polish with a clean soft cloth.
Warranty Detail
Vitreous China: 15-Year Ceramic Warranty – 12 Months Labor.
Mechanism: 3-Year Replacement Warranty – 12 Months Labor
Seat: 1 Year Replacement Warranty
- 2/820 Princes Hwy, Springvale VIC 3171
- P: (03) 9548 1033
- info@choicesupplies.com.au
- www.choicesupplies.com.au
Dimensions are approximate. The information provided in this brochure is representative of the actual products available at the time of printing. Due to our policy of continuous product development, the designs and specifications depicted are subject to change without notice. Please confirm all particulars with your consultant prior to purchase. Each product is covered by a limited warranty. Full terms and conditions are available from your sales consultant.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>