RESPAWN 110 Ergonomic Gaming Chair Instruction Manual
- June 14, 2024
- RESPAWN
Table of Contents
RESPAWN 110 Ergonomic Gaming Chair
Product Information
The product is a chair from RESPAWN. It comes with various components and tools necessary for assembly. The chair features a 4-star base (D), casters (F), a gas cylinder (G), a chair back (A) with a headrest insert (C), armrest brackets (I) with arm pads (H), a seat bottom (B), a seat mechanism (J), bracket covers (L1, L2, K1, K2), screw cover caps (Q), and screws of various sizes (M, N, O, P).
Specifications
- Base Type: 4-star
- Casters: 5 in total
- Gas Cylinder: Included
- Chair Back: Adjustable with headrest
- Armrests: Adjustable
- Seat Bottom: Padded
- Seat Mechanism: Tilt tensioner
FAQs
Q: Are the bracket covers interchangeable?
A: No, the bracket covers are side-specific. Make sure to identify them
carefully before attaching them.
PACKAGE CONTENTS
Assembly Instruction
-
Lay out and identify components on a nearby table or flat surface.
-
Turn the 4-star base (D) upside down.
-
Install base arm (E) by angling the arm over the hooked edge and pushing down into 4-star base (D) until seated.
-
Install casters (F) by pushing casters into the 5-star base (D) until seated.
-
Turn the 5-star base over once all casters are installed.
-
Place gas cylinder (G) into the center of the 5-star base (D). Place 5-star base assembly on the floor.
-
Locate the chair back (A) and lay face down. Untuck and pull back the fabric at the headrest.
-
Place headrest insert (C) into the headrest area so the attachment bracket aligns with the screw holes. The headrest insert and chair back should be flush with each other.
-
Use Allen wrench (R) to attach 2 screws (M).
-
Zip the headrest fabric back up.
-
Locate the armrest bracket (I) and center it over the screw holes on the underside of the arm pad (H). Fits universally.
-
Use Allen wrench (R) to attach 2 screws (N).
-
REPEAT steps 11-12 for the remaining arm.
-
Place seat bottom (B), upside down, on a flat surface.
-
Attach the completed arm bracket to the seat bottom using 3 screws (O) with an Allen wrench (R). REPEAT the other side.
-
Locate the seat mechanism (J) and center it over the screw holes in the seat bottom. The tilt tensioner will be at the top toward the front of the seat.
-
Locate 4 screws (O) for each corner of the seat mechanism (J). Start at the top and work around, tightening the screws thoroughly in all 4 locations with the Allen wrench (R).
-
Take the completed seat assembly and place it atop the gas cylinder (G) unit from Step C.
-
Locate the chair back (A) and place it between the seat bottom brackets.
-
Align screw holes on the seat bracket with side holes on the chair back (A).
-
Use 2 screws (O) to securely attach the bracket to the chair back using an Allen wrench (R). REPEAT the other side.
PRO TIP: Bracket covers are side specific so identify carefully. -
Locate lower bracket covers (L1) & (L2) and place over bracket aligning to screw hole. Attach 1 screw (P) with an Allen wrench (R). REPEAT the other side.
-
Locate upper bracket covers (K1) & (K2) and place over bracket aligning to screw hole. Attach 1 screw (P) with an Allen wrench (R). REPEAT the other side.
-
Locate 4 screw cover caps (Q) and place them over screw holes on bracket covers located on each side of the chair.
-
The last step is to sit in your new chair to fully secure the gas cylinder to the seat assembly and make sure the chair is fully functional.
YOU’RE FINISHED, ENJOY!
Documents / Resources
|
RESPAWN 110 Ergonomic Gaming
Chair
[pdf] Instruction Manual
110, 110 Ergonomic Gaming Chair, Ergonomic Gaming Chair, Gaming Chair, Chair
---|---