Blue Marine Chiller 100 Aquarium Cold Unit User Manual

Blue Marine Chiller 100 Aquarium Cold Unit

Dimensions

Specifications

• Product Name: Chiller 100
• Model: Blue Marine Chiller 100
• Dimensions (Fig. A): 140 mm x 242 mm x 330 mm
• Suitable for (seawater) aquariums: 30 to 100 liters
• Principle: Works on the Peltier principle
• Noise Level: Very quiet and vibration-free
• Maintenance: Low-maintenance

General instructions

Read the safety instructions and manual carefully before using this device. Keep the safety instructions and manual for future reference.

Meaning of symbols
The following warning symbols and/or signal words are used in this manual:

• DANGER!
  This means an imminent danger due to electric current. Failure to follow the safety instructions can result in serious or fatal injury and/or serious damage to the product or environment.

• WARNING!
  This means a dangerous situation. Failure to follow the safety instructions can result in moderate or minor personal injury and/or damage to the product or environment.

• NOTICE!

Meaning of the symbols on the device itself

• This device complies with all applicable EU standards.
• This device may not be disposed of with normal household waste but must be collected separately for recycling.

Use
Only suitable for indoor use for aquarium purposes.

• Never let the device run dry. There should always be water in the device when it is operating.
• Only suitable for cooling aquarium water. Do not use it to cool other liquids. Maximum water temperature is 40°C.
• Always feed the water cooler with clean (filtered) water.
• Connect a suitable aquarium pump with a maximum pump capacity of 600 L/h.

Safety
Always follow the safety instructions below for safe use of the device. Failure to follow these instructions may endanger persons or the environment.

• This device must be supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30 mA.
• Ensure the voltage shown on the label matches the main supply voltage.
• Protect the socket and plug against moisture. Use a drip loop to ensure that water cannot reach the wall socket via the power cord.
• Don’t use the device if the device or the cord is damaged. Return the device to your dealer for repair or recycling. If the power cord is damaged, replace it immediately.
• A new cord is available from your dealer.
• Be careful with the combination of water and electricity. Do not operate with wet hands. Dry your hands before operating the device.
• Always switch off all devices in the aquarium before maintenance. Disconnect the plug(s) from the socket.
• Place the device in a dry, well-ventilated place. Make sure the device is not near heat sources and not in direct sunlight.
• This device can be used by children aged 8 years and above, persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge, if they have been given supervision or instructions concerning the use of the device in a safe way and understand the hazards involved. Children shall not play with the device. Cleaning and maintenance of the device shall not be done by children without supervision.
• Modifications to the device may affect safety and are always at your own responsibility. This will void the warranty.

Function

The Blue Marine Chiller 100 is an advanced water cooler for (seawater) aquariums from 30 to 100 litres. You connect the chiller to a circulation pump, the water is cooled as it flows through. The cooler works on the Peltier principle which makes it very quiet, vibration-free and low-maintenance. The water flowing through the cooler should always be clean (filtered). Dirty water can adversely affect the cooling efficiency and cause blockages.

Installation (Fig. A)

• For installation, you need a circulation pump (Blue Marine Reef Power 600, art. N7035375), aquarium hose (ø 9/12 mm or ø 12/16 mm) and hose clamps. These are not included.
• Connect the circulation pump (c) with the aquarium hose and hose clamps to one of the connections on the chiller(a). Place the circulation pump in the sump (b).
• Connect the other aquarium hose to the other connection using a hose clamp and hang the hose end in the sump at some distance from the pump.
• Place the sensor (d) in the sump, near the circulation pump so that it can measure the average water temperature.
• Turn on the circulation pump so that water starts flowing through the chiller.
• Connect the power cable to the chiller and plug it in. Flip switch at the back of the chiller so that it lights up red.

Use (Fig. B)

• Turn on the chiller by pressing the RST key. The display will turn on. To turn the chiller off, press and hold the RST key for three seconds.
• Press the Set button, the digits start flashing and LED (f) lights up.
• Press to set the desired temperature. If you want to go up or down faster, press and hold the button.
• Press Set to confirm the setting or wait 5 seconds (the digits stop flashing).
• Should you accidentally press the Set button too long, you will enter the factory settings menu. Press Set or wait 5 seconds to exit this menu. Do NOT modify the factory settings.
• The chiller starts cooling when the water temperature is 1°C above the set value and stops once the set temperature is reached (example: at a set value of 26°C, the chiller keeps the water temperature between 26-27°C). LED (e) lights up during cooling.

Maintenance

• Turn off the chiller with the switch and unplug it.
• Clean the outside of the chiller regularly with a dry or slightly damp cloth.
• Disconnect the hoses if they are dirty on the inside and rinse them under running water or use a special brush to clean the inside.
• Reconnect the hoses and secure them with the hose clamps.
• Put the plug into the socket and flip the switch again.
• After a brief power interruption, the chiller will continue cooling with the set temperature.

Allgemeine Anweisung

Lesen Sie die Sicherheitshinweise und das Handbuch sorgfältig durch, bevor Sie das Gerät verwenden. Bewahren Sie die Sicherheitshinweise und das Handbuch für den späteren Gebrauch auf.

Bedeutung der Symbole
Die folgenden Warnsymbole und/oder Signalwörter werden in diesem Handbuch verwendet:

Warranty

2-year manufacturer’s warranty on materials and construction defects. Devices must be returned complete with all components, accompanied with an official proof of purchase confirming a purchase date for any warranty claims. Incomplete devices of which parts are missing, and devices without proof of purchase are not eligible for warranty. After receiving and checking, we will determine whether the device will be repaired or replaced. For a device repaired or replaced under warranty, the remaining time of the original warranty period applies. Carefully read the instructions on installation, use and maintenance. Damage due to incorrect use, damage due to contamination or not cleaning the device and damage to the cord are not covered by the warranty. Always keep the proof of purchase, without proof of purchase the warranty will be void!

Vlietweg 8, NL-4791 EZ Klundert, The Netherlands www.aquadistri.com

References

• Aquadistri | For A Successful Aquarium, Pond & Terrarium

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>