KEAIDE KA-600 DJ Laser Lights for Party 3D Animation User Manual

KEAIDE KA-600 DJ Laser Lights for Party 3D Animation

Questions or Concerns?

Our team will solve your any problems in 24 hours

This manual contains important laser. system safety and operation information. Read and understand all instructions prior to powering on laser unit the. first time, to avoid laser eye injury and to avoid breaking the law. Keep this manual in a safe place for future reference.

General Instructions

Unpacking:

Thank you for purchasing this product. Please read user guide for safety and operations information before using the product. Keep this manual for future reference. This product can create perfect light programs and effects since it has passed a series of strictly tests before delivery.
Please check the attachments listed on the page after opening the carton. Immediately upon receiving a fixture, carefully unpack the box. Check the box contents to ensure that all parts are present and that they are in good condition. If any part appears damaged from shipping, or if the box shows signs of mishandling, notify the shipper immediately. ln addition, retain the box and all the packing material for inspection. In any event, save the carton and all packing material because, in case that you have to return the fixture to the factory, you will have to do so in its original box, with its original packing.

What is included: 1 Light, 1 Power Cable, 1 *User Guide

Safety Notice: Please read the following notes carefully because they include important safety information about the installation, usage and maintenance of this product. lt is important to read all these notes before starting to work with this product.

Lasers can be hazardous and have unique safety considerations. Permanent eye injury and blindness is possible if lasers are used incorrectly. Pay close attention to each safety REMARK and WARNING statement in the user manual. Read all instructions careful.

Laser Safety Warnings

Potential laser injury hazard exists with this product! Read these Instructions carefully, which include important information about installation, safe use and service!

Caution:

• Avoid direct eye contact with laser light. Never intentionally expose your eyes or others to direct laser radiation.
• This laser product can potentially cause instant eye injury or blindness if laser light directly strikes the eyes.
• It is illegal and dangerous to shine this laser into audience areas, where the audience or other personnel could get direct laser beams or bright reflections into their eyes.
• It is a US Federal offense to shine any laser at aircraft.

NON-INTERLOCKED HOUSING WARNING

• This unit contains high power laser devices internally. Do not open the laser housing, due to potential exposure to unsafe levels of laser radiation. The laser power levels accessible if the unit is opened can cause instant blindness, skin burns and fires.

Installation

• Laser effects projected 3 meters (9.8 ft) above the audience are eye sate. A survey should be taken to assess the likelihood of any reflective surfaces (such as high windows, chrome bars etc) bouncing stray beams back down into the audience.
• Using a fastening clamps on the light and tight to the ceiling in a strong hook .
• Make sure its correct power output and plug the power cable to the wall socket.
• Power must be in earth’ Power on the light.
• Do not shoot the beams to the audience’
• Do not look direct into the laser aperture once the laser light is ON. Please pay attention to the Laser Danger Warning Label!

Cleaning

Fixture Cleaning: Due to fog residue, smoke, and dust cleaning the internal and external lenses should be carried out periodically to optimize light output.

1. Use normal glass cleaner and a soft cloth to wipe down the out- side casing.
2. Clean the external optics with glass cleaner and a soft cloth every 20 days.
3. Always be sure to dry all parts completely before plugging the unit back in. Cleaning frequency depends on the environment in which the fixture operates (I.e. smoke, fog residue, dust, dew). In heavy use we recommend cleaning on a monthly basis. Periodic cleaning will ensure longevity, and crisp beam output.

Caution

After setting up, and before public use, test laser to ensure proper function. Do not use if any defect is detected. Do not use if laser emits only one or two laser beams rather than dozens/ hundreds, as this could indicate damage to the diffraction grating optic, and could allow emission of higher laser levels above Class 3B.
Do not point lasers at people or animals. Never look into the laser aperture or laser beams.
Do not point lasers in areas in which people can potentially get exposed, such as uncontrolled balconies, etc.
Do not point lasers at highly reflective surfaces, such as windows, mirrors and shiny metal. Even laser reflections can be hazardous.
Never point a laser at aircraft, this is a federal offense.
Never point un-terminated laser beams into the sky.
Do not expose the output optic (aperture) to cleaning chemicals.
Do not use laser if the laser appears to be emitting only one or two beams.
Do not use the laser if the housing is damaged, the housing is open, or if the optics appear damaged in any way.
Never open the laser housing. The high laser power levels inside of the protective housing can start fires, bum skin and will cause instant eye injury.
Never leave this device running unattended.

• During Assembly, operation, maintenance, please pay special attention to avoid possible exposure to laser and collateral radiation in excess of the accessible emission limits.
• Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
• Protective eye wear is typically required where direct viewing of a Class 3B laser beam may occur.

The projector must be installed in a location with adequate distance

Laser Expected Lifespan

Laser gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration of this decline. Packaged in clusters, Laser exhibit higher operating temperatures than in ideal or singular optimum conditions. For this reason when all color Laser are used at their fullest intensity, life of the Laser is significantly reduced. It is estimated that a viable lifespan of 5,000 to 10,000 hours will be achieved under normal operational conditions. If improving on this lifespan expectancy is of a higher priority, place care in providing for lower operational temperatures. This may include climatic-environmental and the reduction of overall projection intensity.

Attention!
The scan speed of any laser software control must be less than the scanner speed of your laser light, otherwise, the patterns possible have distortion, or else the scanner will be damaged by overspeed running software!

Technical Specification

• Feature: Animation laser with high-speed optical scanner to create animated graphics. hundreds of beam show and graphics show patterns, and with the function of color change, AUTO, Sound activate, rotating, movement, rotation, zoom(+/-), drawing and speed etc.
• Scanner High-speed optical scanner, big angle scanning
• Play Mode Sound Active, AUTO-Beam, AUTO-Animation, DMX, Master/ Slave, PC Control
• DMX channel: 6CH/34CH
• Digital display function
• Sound-activated sensitivity regulation : Turn the knob clockwise to change the sensitivity from low to high
• Power Supply Bi-Voltage AC100V to 240V/2A, 50/60HZ
• Applicable place: logo projector, company advertising, superstar fashion show, DJs, Bands, Bars, Pubs, Clubs, Roller skating rinks, KTV, Family Party, etc.

Fixture Rear Plate

Digital display function

“Menu” is Menu, “Enter” is confirm, “Previous” is UP, “Next” is down.

1. Displaying mode setting: press MENU to switch the modes: press effects, professional DMX512, simple DMX512.
2. press effects: press ENTER to switch AUTO and Sound mode
3. Press AUTO mode: SE + digits, (the fourth Decimal point OFF, digit is the displaying serial number)
4. press Sound mode: SE + digits, (the fourth Decimal point ON, digit is the displaying serial number) press UP/DOWN to change the serial number.
5. Professional DMX512 mode: A + digit (digit means the DMX value)
6. Tethered is DMX signal, the fourth Decimal point ON; if there is no DMX signal, the fourth Decimal point OFF.
7. laser light setup mode: press MENU to enter the laser light setup mode.
8. Optional modes: X-invert, Y-invert, XY co-invert, X-invert position, Y-invert position, Remote control OFF.
9. X-Invert
10. X-invert display: x. INV
11. Under X-invert mode, press ENTER to change the direction.
12. Forward direction: the fourth Decimal point OFF; backward: the fourth Decimal point ON
13. Y-invert
14. Y-invert display: y. TNV
15. Under Y-invert mode, press ENTER to change the direction
16. Forward direction: the fourth Decimal point OFF; backward: the fourth Decimal point ON
17. XY co-invert
18. XY co-invert display: \.INV
19. Under this mode, press ENTER to change the direction
20. Forward direction: the fourth Decimal point OFF; backward: the fourth Decimal point ON
21. Remote control OFF
22. Remote control OFF display: OFF
23. Under this mode, press ENTER to ON/OFF the remote control function.
24. the fourth Decimal point OFF; OFF: the fourth Decimal point ON

Master/Slave mode:
In the digital display, set the “Slave” unit into “E.00 I”.

DMX Control
The system only accepts the DMX512 signal of international standard to control the system.

OMX Control Parameter Chart

Simple DMX mode:

1. Group number over the max, then the program is default with the max group.
2. When CH2 is under preset mixed mode, this Channel is invalid.)

| 0–15| Group 1 patterns
16–31| Group 2 patterns
……|
192–223| Group 15 patterns
224–255| Group O patterns
CH4| Theme selection| 0–255| Each value is for one pattern.

1. Group number over the max, then the program is default with the max group.
2. When CH2 is under preset mixed mode , this Channel is invalid.)

CHS| Color selection| 0–31| Full color
32–63| red
64–95| yellow
96–127| green
128–159| cyan
160–191| blue
192–223| pink
224–255| white
CH6| Speed adjustment| 0| No movement
1–255| Slow to fast
CH!| Laser ON/OFF| 0| Laser OFF
---|---|---|---
1-99| AUTO
100-199| Sound active
200-254| Saving
255| Pattern A, OFF
CH2| | 0-49| Out of bounds Crossing
50-99| Out of bounds Reentry
Out of bounds and| 100-149| Out of bounds Blanking
Pattern size| | 150-199| Pattern zoom out, Out of bounds Blanking
200-255| Saving

CH3

| Group selections| 0-223| Group 1
244-255| Group 0
CH4| Pattern selections| 0-255| Each value for one pattern; If over the pattern numbers, then grogram displaying the max number
CH5| Pattern Zoom IN/OUT| 0-127| Static pattern size
128-159| Dynamic Zoom OUT. the bigger value, the faster speed
160-191| Dynamic Zoom IN. the bigger value, the faster speed
192-223| Dynamic Zoom IN/OUT. the bigger value, the faster speed
224-255| Dynamic Zoom Rotation. the bigger value, the faster speed
CH6| Pattern rotation| 0-127| Static rotation

128-159

| Dynamic rotation 2 circles clockwise and counter clockwise. the bigger value, the faster speed

160-191

| Dynamic rotation 1 circle clockwise and counter clockwise. the bigger value, the faster speed
192-223| Dynamic rotation clockwise. the bigger value, the faster speed
224-255| Dynamic rotation counter clockwise . the bigger value, the faster speed
CH7| X Moving| 0-127| Static X moving
128-159| Dynamic UP moving wave effect. the bigger value, the faster speed
160-191| Dynamic DOWN moving wave effect. the bigger value, the faster speed
192-223| Dynamic LEFT moving. the bigger value, the faster speed
224-255| Dynamic RIGHT moving. the bigger value, the faster speed
CHS| Y Moving| 0-127| Static Y moving
128-159| Dynamic RIGHT moving wave effect the bigger value, the faster speed
160-191| Dynamic LEFT moving wave effect. the bigger value, the faster speed
192-223| Dynamic DOWN moving. the bigger value, the faster speed
224-255| Dynamic UP moving. the bigger value, the faster speed
CH9| X Zoom lN/OUT| 0-127| Static size
128-159| Dynamic UP moving distortion. the bigger value, the faster speed
160-191| Dynamic DOWN moving distortion. the bigger value, the faster speed
192-223| Dynamic Zoom I N/OUT
224-255| Dynamic Rotation Zoom IN/OUT. the bigger value, the faster speed
CH 10| Y Zoom I N/OUT| 0-127| Static size
128-159| Dynamic RIGHT moving distortion. the bigger value, the faster speed
160-191| Dynamic L E FT moving distortion. the bigger value, the faster speed
192-223| Dynamic Zoom lN/OUT
224-255| Dynamic Rotation Zoom IN/OUT. the bigger value, the faster speed
CH 11| Fixed Color setting| 0| Original color
---|---|---|---
1-255| Color change with each n dot
CH12| Pattern color change| 0-7| Original color
8-15| red
16-23| yellow
24-31| green
32-39| cyan
40-47| blue
48-55| pink
65-63| white
64-95| Whole pattern RGB. the bigger value, the faster speed
96-127| Whole pattern YCP. the bigger value, the faster speed
128-159| Whole pattern RGBYCPW. the bigger value, the faster speed
160-191| 7 Color RGBYCPW. the bigger value, the faster speed
192-223| Sine Chasing color change
224-255| Cosine Chasing color change
CH13| Dots| 0-63| Original Dots
64-127| Pattern no Dots effect, sweep line blanking
128-159| Pattern no Dots effect, Sweep line no blanking
160-255| Saving
CH14| Drawing and other functions(working with Channel 15)| 0-255| On CH15 value 0-127, pattern moving drawing all ON to keep the time
0-255| On CH15 value 128-255, walking drawing line quantity
CH15| Drawing (CH15 and CH14 together)| 0-63| Sine manual drawing
64-127| Cosine manual drawing
128-159| Dynamic drawing A Effects. the bigger value, the faster speed
160-191| Dynamic drawing B Effects. the bigger value, the faster speed
192-223| Dynamic drawing C Effects. the bigger value, the faster speed
224-255| Dynamic drawing D Effects. the bigger value, the faster speed
CH16| Twist pattern change| 0-255| The more value, the less twisting (notes: when zoom in, rotation, moving, rolling twisting effects, CH16 can control the effect)
CH17| Grating selection (notes: in some  sections, more value then less gobo angle)| 0-19 20-39 40-59 3 ….. 240-255 13| Grating group 1. .1. The bigger digit, the smaller pattern.
CH18| ON/OFF Laser| 0| All OFF
1-99| AUTO
100-199| SOUND
200-254| Saving
255| Group A OFF , Group BON
CH19| Out of bounds and oat tern size| 0-49| Out of bounds Crossing. The bigger digit, the smaller pattern.
CH19| Out of bounds and pattern size| 50-99| Out of bounds Reentry
---|---|---|---
100-149| Out of bounds Blanking
150-255| Saving
0-49| Out of bounds Crossing
CH20| No function| blank|
CH21| Pattern selections| 0-255| Each value for one pattern; If over the pattern numbers, then lockram dissolving the max number
CH22| Pattern Zoom I N/OUT| 0-127| Static pattern size
128-159| Dynamic Zoom OUT. the bigger value, the faster speed
160-191| Dynamic Zoom IN. the bigger value, the faster speed
192-223| Dynamic Zoom IN/OUT. the bigger value, the faster speed
224-255| Dynamic Zoom Rotation. the bigger value, the faster speed
CH23| Pattern rotation| 0-127| Static rotation
128-159| Dynamic rotation 2 circles clockwise and counterclockwise. the bigger value, the faster speed
160-191| Dynamic rotation 1 circle clockwise and counterclockwise. the bigger value, the faster speed
192-223| Dynamic rotation clockwise. the bigger value, the faster speed
224-255| Dynamic rotation counter clockwise. the bigger value , the faster speed
CH24| X Moving| 0-127| Static X moving
128-159| Dynamic UP moving wave effect. the bigger value, the faster speed
160-191| Dynamic DOWN moving wave effect. the bigger value, the faster speed
192-223| Dynamic LEFT moving. the bigger value, the faster speed
224-255| Dynamic RIGHT moving. the bigger value, the faster speed
CH25| Y Moving| 0-127| Static Y moving
128-159| Dynamic RIGHT moving wave effect. the bigger value, the faster speed
160-191| Dynamic LEFT moving wave effect. the bigger value, the faster speed
192-223| Dynamic DOWN moving. the bigger value , the faster speed
224-255| Dynamic UP moving. the bigger value , the faster speed
CH26| X Zoom IN/OUT| 0-127| Static size
128-159| Dynamic UP moving distortion. the bigger value, the faster speed
160-191| Dynamic DOWN moving distortion. the bigger value, the faster speed
192-223| Dynamic Zoom IN /OUT
224-255| Dynamic Rotation Zoom I N/OUT. the bigger value, the faster speed
CH27| Y Zoom IN/OUT| 0-127| Static size
128-159| Dynamic IUGHT moving distortion. the bigger value, the faster speed
160-191| Dynamic LEFT moving distortion. the bigger value, the faster speed
192-223| Dynamic Zoom IN/OUT
224-255| Dynamic Rotation Zoom TN/OUT. the bigger value, the faster speed
CH28| Fixed Color setting| 0| Original color
1-255| Color change with each n dot
CH29| Pattern color change| 0-7| Original color
8-15| red
16-23| yellow
24-31| green
CH29| Pattern color change| 32-39| cyan
---|---|---|---
40-47| blue
48-55| pink
65-63| white
64-95| Whole pattern RGB. the bigger value, the faster speed
96-127| Whole pattern YCP. the bigger value, the faster speed
128-159| Whole pattern RGB CPW. the bigger value, the faster speed
160-191| 7 Color RGB CPW. the bigger value, the faster speed
192-223| Sine Chasing color change
224-255| Cosine Chasing color change
CH30| Dots| 0-63| Original Dots
64-127| Pattern no Dots effect, sweep line blanking
128-159| Pattern no Dots effect, Sweep line no blanking
160-255| Saving
CH31| Drawing and other functions(working with Channel 15)| 0-255| On CHIS value 0-127, pattern moving drawing all ON to keep the time
0-255| On CHIS value 128-255, walking drawing line quantity
CH32| Drawing (CH15 andCHl4 together)| 0-63| Sine manual drawing
64-127| Cosine manual drawing
128-159| Dynamic drawing A Effects. the bigger value, the faster speed
160-191| Dynamic drawing B Effects. the bigger value, the faster speed
192-223| Dynamic drawing C Effects. the bigger value, the faster speed
224-255| Dynamic drawing D Effects. the bigger value, the faster speed
CH33| Twist pattern change| 0-255| The more value, the less twisting (notes: when zoom in, rotation, moving, rolling twisting effects, CHl6 can control the effect)
CH34| Grating selection (notes: in some sections, more value then less gobo angle)| 0-1920-3940-593 …..240-25513| Grating group 1…1. The bigger digit, the smaller pattern.

Warranty Warnings

1. Damages caused by the disregard of this user manual are not subject to Warranty.
   The dealer will not accept liability for any resulting defects or problems.

2. Please consider that unauthorized modifications on the device are forbidden due to safety reasons.
   Please note that damages caused by manual modifications on the device or unauthorized operation by unqualified persons are not subject to warranty.

3. Tf this device will be operated in any way different to the one described in this manual, it may suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-circuit, burns electric shock, etc.

For any questions about this light, please contact your dealer or our company for service.

Product Description

| Turn on the light| | White laser color is always working
---|---|---|---
| Automatic line rotation| | Red laser color is always working
| Turn off lights| | Green laser color is always working
DMX34 channel| | Blue laser color is always working
| The sound active sensor works in high level of sensitivity, light works immediately with some SOUNDS, and turn off immediately without SOUNDS.| | Red and green laser color is always working
| DMX 6 channel| | Green and blue laser color is always working
| Beam pattern effect| | Red and blue laser color is always working
| pattern effects| | Adjust X axis
| Line and 3D pattern effects| | Adjust Y axis
| Red and green and blue laser color is always working| | Exchange XY axis

TIPS:

1. Please note that all these perfect effects are created “In Smoke Environment”. Without smoke, just can see some pattern effects and the dynamic beams and scanning effects will not see.
2. For the best user experience, the sound-activated mode should be used together with a loud volume speaker. Do not use the phone speaker to test the sound-activated mode since the phone speaker is not powerful enough to trigger sound-activated mode.
3. Built-in motor spins quickly and may make a sound during working, this is a normal phenomenon.
4. Please do not keep your eyes on the light for a long time, so as not to damage your eyes. Keep away from children.
5. Please use a professional glass cleaner regularly and clean the lens with a flannel to ensure the maximum brightness output of the light and extend the life of the light.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>