TIDRADIO GMRS Two Way Radio User Manual

TIDRADIO GMRS Two Way Radio

PREFACE

Thank you for purchasing this product. It is a multitask GMRS transceiver. Combining the latest technology in radio communication along with a sturdy mechanical frame, This product is the ideal and effective solution for the professionals who need to stay in touch with the working team (in construction sites, buildings, shows, trade fairs or hotels) or for leisure users that just want to keep up with friends and family.

IMPORTANT NOTICE

To help you ward off bodily injury or property loss that may arise from improper operation, please read all the information carefully before using our products. This contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulation.

Safety Information for Radios

Your wireless handheld portable transceiver contains a low power transmitter. When the talk button is pushed, it sends out radio frequency (RF) signals. The device is authorized to operate at a duty factor not to exceed 50%. In August 1996, the Federal Communications Commissions (FCC) adopted RF exposure guidelines with safety levels for handheld wireless devices.

GETTING STARTED

Regulations and Safety Warnings

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Important: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device. Your radio is set up to transmit a regulated signal on an assigned frequency. It is against the law to alter or adjust the settings inside the radio to exceed those limitations. Any adjustments to your radio must be made by qualified technicians.

To be safe and sure:

• Never open your radio’s case.
• Never change or replace anything in your radio except the battery.

Your radio might cause TV or radio interference even when it is operating properly. To determine whether your radio is causing the interference, turn it off. If the interference goes away, your radio is causing it. Try to eliminate the interference by moving your radio away from the receiver. If you cannot eliminate the interference, the FCC requires that you stop using the radio.

Hazardous Environments: Do not operate the radio in hazardous environments. Explosion or fire may result. Do not operate the radio near unshielded electrical blasting caps. Under certain conditions, radios can interfere with blasting operations and may cause an explosion. Turn your radio OFF to prevent accidental transmission when in a blasting area or in areas posted: “Turn off two-way radio.” Construction crews often use remote control RF devices to set off explosives.

Care and Safety: To clean the radio, use a soft cloth dampened with water. Do not use cleaners or solvents because they can harm the body of the unit and leak inside, causing permanent damage. Use a dry, lint-free cloth to clean the battery contacts.

FCC STATEMENT

RF Exposure Information

WARNING:  Read this information before using the radio. In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC 96-326 adopted an updated safety standard for human exposure to radio frequency electromagnetic energy emitted by FCC regulated transmitters.

Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies. The design of the radio complies with the FCC guidelines and these international standards.
Never allow children to operate the radio without adult supervision and the knowledge of the following guidelines.

WARNING:  It is up to the user to properly operate this radio transmitter to insure safe operation. Please adhere to the following:

• Use only the supplied or an approved antenna. Unauthorized antennas, modifications, or attachments could impair call quality, damage the radio, or result in violation of FCC regulations.
• Do not use the radio with a damaged antenna.
• If a damaged antenna comes into contact with the skin, a minor burn may result. Please contact your local dealer for a replacement antenna.

Hand-held Operation (Held-to-Face)

• This device was evaluated for typical hand-held (held-to- face) operations with a 1 inch spacing from the front of the radio.
• For hand-held operation, the radio should be held 1 inch from the user’s face in order to comply with FCC RF exposure requirements.
• For more information about RF exposure, please visit the FCC web site at www.fcc.gov.

Body-worn Operation

This device was evaluated for body-worn operations with the supplied belt-clip accessory. (All necessary accessories are included in the package; any additional or optional accessories are not required for compliance with the guidelines.) Third party accessories (unless approved by the manufacturer) should be avoided as these might not comply with FCC RF exposure guidelines.

For more information about RF exposure, please visit the FCC web site at www.fcc.gov.

GMRS Communication

This GMRS (General Mobile Radio Service) feature is a land-mobile service available for short-distance, two-way communications in the USA. You must have a valid FCC license to communicate on these channels. The GMRS/FRS frequencies that radio this radio uses are set aside for communicating with others while hiking, biking, and working; keeping track of family and friends at a crowded public event; checking with travel companions in another car; talking with neighbors; arranging meeting spots with others while shopping at the mall. Licensed users will be issued a call sign by the FCC, which should be used for station identification when operating this radio. GMRS users should also cooperate by engaging in permissible transmissions only, avoiding channel interference with other GMRS users, and being prudent with the length of their transmission time.

FCC License Required

This two-way radio operates on GMRS (General Mobile Radio Service) frequencies which require an FCC (Federal Communications Commission) license. A user must be licensed prior to transmitting on the GMRS band with this radio. Serious penalties could result for unlicensed use of GMRS channels, in violation of FCC rules. Operation of this radio is subject to additional rules specified in 47 C.F.R. Part 95. For licensing information and application forms, please call the FCC Hotline at 800418-FORM. Request form #159 and form #605. Questions regarding the license application should be directed to the FCC at 888-CALL-FCC. Additional information is available on the FCC’s website at www.fcc.gov.

NOTE: Even if you operate this radio on FRS (Family Radio Service) channels at low power (0.5 watt), you are required to have an FCC license. Because this radio operates in the 0.5 to 5 watt GMRS power range all GMRS rules apply and will require you have a GMRS license even for FRS (Family Radio Service) communication. Normal FRS only radios operate at a maximum power of 0.5 watt (500 mill watt) power and have an integral (non-detachable) antenna.

Replacement or substitution of transistors, regular diodes or other parts of a unique nature, with parts other than those recommended by our company may cause a violation of the technical regulations of part 95 of the FCC rules, or violation of type acceptance requirements of part 2 of the rules.

MORE INFORMATION

Main features

• 22 Modifiable GMRS Channels (RX &TX)
• Channel and frequency mode (MR/VFO) are selectable
• Scanner function, precise setting of scanning frequency range, useful frequencies can be saved as channels
• 158 Programmable Scanner Channels (Receive Only)
• Output power: 5W/0.5W (GMRS)
• 155 Privacy Codes (50 CTCSS codes/ 105 DCS codes)
• SOS Emergency function
• Built-in FM Radio (76-108MHz)
• 2pin Kenwood accessory jack
• TOT (Time out timer)
• Setting and storing of channel names
• Busy Channel Lockout function (BCL)
• Repeater shift
• 8 Modifiable GMRS Repeater Channels (RX & TX)
• Dual band, dual display & dual band single display (SYNC)
• Large screen, full keyboard, open menu operation, get rid of the shackles of programming software
• 11 NoAA weather channels to receive and scan
• CTCSS and DCS codes Scan
• 1750Hz tone for repeaters
• Three scan recovery methods: carrier, search, time
• VOX, Channels Scan, Frequency Scan, Dual Watch functions
• Channel or frequency mode selection
• DTMF function
• Power Save
• Frequency step: 2.5/5/6.25/10/12.5/25KHz.
• Squelch adjustable in 9 levels

About Range

This product series radios are designed to give you maximum range under optimum conditions.

• Maximum Range: Little to No sight Obstruction.
• Medium Range: Partial Obstruction to line of sight.
• Short Range: Major Obstruction to Ling of Sight.

Optimum Conditions are:

• Over water
• Open rural areas without obstructions
• Flat areas where you can see the other person

To ensure you get maximum range:

• Be sure to use fresh or fully charged batteries – low batteries will cause low power conditions.
• Be sure you are on a GMRS channel – FRS channels are restricted by the FCC to low power.
• Be sure to set your radio to use Hi power.

Maintenance

Your Two Way Radio is an electronic product of exact design and should be treated with care. The suggestions below will help you to fulfil any warranty obligations and to enjoy this product for many years.

• Do not attempt to open the radio for any reason! The radio’s precision mechanics and electronics require experience and specialized equipment; for the same reason, the radio should under no circumstances be realigned as it has already been calibrated for maximum performance. Unauthorized opening of the transceiver will void the warranty.
• Do not store the Radio under the sunshine or in hot areas.
• High temperatures can shorten the life of electronic devices, and warp or melt certain plastics.
• Do not store the radio in dusty and dirty areas.
• Keep the Radio dry. Rainwater or damp will corrode electronic circuits.
• If it appears that the Radio diffuses peculiar smell or smoke, please shut off its power immediately and take off the charger or battery from the radio.
• Do not transmit without antenna.

BATTERY INFORMATION

Charging the Battery Pack

The Li-ion battery pack is not charged at the factory; please charge it before use. Charging the battery pack for the first time after purchase or extended storage (more than 2 months) may not bring the battery pack to its normal maximum operating capacity. Best operation will require fully charging/ discharging the battery two or three times before the operating capacity will reach its best performance. The battery pack life may be depleted when it’s operating time decreases even though it has been fully and correctly charged. If this is the case, replace the battery pack.

Charger Supplied

• Please use the specified charger provided by our company.
• Other models may cause explosion and personal injury. After installing the battery pack, and if the radio displays low battery with a voice prompt, please charge the battery.

Use Caution with the Li-ion Battery

• Do not short the battery terminals or throw the battery into a fire. Never attempt to remove the casing from the battery pack, as our company cannot be held responsible for any accident caused by modifying the battery.
• The ambient temperature should be between 5℃-40℃ (40˚F – 105˚F) while charging the battery. Charging outside this range may not fully charge the battery.
• Please turn off the radio before inserting it into the charger. It may otherwise interfere with correct charging.
• To avoid interfering with the charging cycle, please do not cut off the power or remove the battery during charging until the green light is on.
• Do not recharge the battery pack if it is fully charged. This may shorten the life of the battery pack or damage the battery pack.
• Do not charge the battery or the radio if it is damp. Dry it before charging to avoid damage.

WARNING

When keys, ornamental chain or other electric metals contact the battery terminal, the battery may become damage or injure a human. If the battery terminals are short circuited it will generate a lot of heat. Take care when carrying and using the battery. Remember to put the battery or radio into an insulated container. Do not put it into a metal container.

How to Charge

• Plug the AC adaptor into the AC outlet, and then plug the cable of the AC adaptor into the DC jack located on the back of the charger. The indicator light blinks orange and is then ready to charge a battery.
• Plug the battery or the radio into the charger. Make sure the battery terminals are good in contact with charging terminals. The indicator light turns to red— charging begins.
• It takes approximately 2-5 hours to fully charge the battery. When the lamp lights green, the charging is completed. Remove the battery or the radio unit with its battery from socket.

When charging a radio (with battery) the indicating lamp will not turn into green to show the fully charged status if the radio is powered on. Only when the radio is switched off will the lamp indicate normal operation. The radio consumes energy when it is power-on, and the charger cannot detect the correct battery voltage when the battery has been fully charged. So the charger will charge the battery in constant voltage mode and fail to indicate correctly when the battery has been fully charged.

LED Indicator

NOTE: Trouble means battery too warm, battery short-circuited or charger short-circuited.

How to Store the Battery

• If the battery needs to be stored, keep it in status of 80% discharged.
• It should be kept in low temperature and dry environment.
• Keep it away from hot places and direct sunlight.
  • Do not short circuit the battery terminals.
  • Never attempt to remove the casing from the battery pack.
  • Never store the battery in unsafe surroundings, as a short may cause an explosion.
  • Do not put the battery in a hot environment or throw it into a fire, as it may cause an explosion.

INSTALLATION OF ACCESSORIES

Before the radio is ready for use we need to attach the battery pack, as well as charge the battery.

Installing the belt clip

• At the back of the radio there are two parallel screws mounted above the battery, remove these and thread them through the holes on the belt clip as you screw them back into the radio body.
• Removing the Belt Clip: Unscrew counter-clockwise to remove the belt clip.

Installing the battery pack

Before attaching or removing the battery make sure your radio is turned off by turning the power/volume knob all the way counter-clockwise.

• Make sure the battery is aligned in parallel with the radio body with the lower edge of the battery about 1-2cm below the edge of the radio.
• Once aligned with the guide-rails, slide the battery upward until you hear a click as the battery locks in place.

Remove the battery pack

• To remove the battery, press the battery release above the battery pack, as you slide the battery downward.

Installing the Additional Speaker/Microphone (Optional)

• Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack.

RADIO OVERVIEW

Buttons and controls of the radio

• 1. Antenna
• 2. Power Switch / Volume control: Rotate to switch on/off the radio and adjust the volume
• 3. LCD screen
• 4. VFO/MR: Channel Mode/Frequency Mode
• 5. BL Key: Bluetooth programming function
• 6. A/B key: press to switch A/B band
• 7. Speaker
• 8. Microphone
• 9. keypad: channel mode, enter the channel number; frequency mode, enter the working frequency; menu mode, directly enter the menu items
• 10. PTT key: Transmit key, hold the key to speak, release the key after speaking, and receive incoming calls.
• 11/12. Side UP/ DOWN keys: Short press and long press to use the function, the function can be customized by writing the frequency software flashlight, radio, TONE, alarm, weather function
• 13. MIC/SP: External speaker/mike jacks.
• 14. Flashlight
• 15. Top Key: Short press and long press to use the function, the function can be customized by writing the frequency software flashlight, radio, TONE, alarm, weather function
• 16. Indicator: Red when transmitting; Green when receiving.
• 17. Battery latch

Main controls and parts of the radio

Status Indications

The status LED has a very simple and traditional design.

Main keypad controls

(MENU)key: It is used for activating the MENU, choose each MENU selection and confirm the parameter. In standby mode, press and hold the key to switch between frequency (VFO) mode and channel (MR) mode. To save frequencies to channel memory you must be in Frequency (VFO) mode. Memory mode is sometimes also referred to as Channel mode.

• key: Press it for more than 2 seconds, the channel and frequency will move upwards rapidly; in SCAN mode, press this control to move the scanning upwards.
• key: Keep it pressed it for more than 2 seconds, the channel and frequency will move downwards rapidly; in SCAN mode, press this control to move the scanning downwards.

Numeric keypad

• With these keys you can input the information or your selections on the radio. In tx mode, push the number keys to send a corresponding DTMF code.

Key

• A short momentary press of the key enables the reverse function.
• If you press this button for more than 2 seconds you will lock/unlock the keypad.

BASIC OPERATIONS

Power on the radio

• Turning the unit on
  • To turn the unit on, simply rotate the volume/power knob clockwise until you hear a “click”. If your radio powers on correctly there should be an audible double beep after about one second and the display will show a message or flash the LCD depending on settings for about one second. Then it will display a frequency or channel. If the Voice prompt is enabled, the voice will announce “frequency mode” or “channel mode”.
• Turning the unit off
  • Turn the volume/power knob counter-clock wise all the way until you hear a “click”. The unit is now off.

Adjusting the volume

• To turn up the volume, turn the volume/power knob clock-wise.
• To turn the volume down, turn the volume/power knob counter-clock-wise. Be careful not to turn it too far, as you may inadvertently turn your radio off.

Channel selection

• There are two modes of operation: Frequency (VFO) mode, and Channel or Memory (MR) mode.
• For everyday use, Channel (MR) mode is going to be a whole lot more practical than Frequency (VFO) mode. However,
• Frequency (VFO) mode is very handy for experimentation out in the field. Frequency (VFO) mode is also used for programming channels into memory.
• In Channel (MR) mode you can navigate up and down the channel by using the / keys or the encoder.
• Ultimately which mode you end up using will depend entirely on your use case.

Making a call

• Channel mode call: After selecting a channel, hold down the [PTT] key to initiate a call to the current channel. Speak into the microphone with normal tone. Initiate a call, the red LED is on.
• Frequency mode call: The off state, hold press [MENU] key to open the radio, switching to the frequency mode, the frequency range allowed entering, press the [PTT] key, a call to the current channel. Speak into the microphone with normal tone. Initiate a call, the red LED is on.
• Receive a call: When you release the [PTT] key, you can answer it without any action.
  • When receiving a call, the green LED is on.

NOTE: To ensure the best reception volume, keep the distance between the microphone and the mouth at the time of transmission from 2.5 cm to 5 cm.

Frequency (VFO) mode

In Frequency (VFO) mode you can navigate up and down the band by using the / keys. Each press will increment or decrement your frequency according to the frequency step you’ve set your transceiver to. You can also input frequencies directly on your numeric keypad with kilohertz accuracy. The following example assumes the use of a 12.5 kHz frequency step.

Example:  Entering the frequency 432.56250 MHz on display A

• In standby mode, switch to the frequency (VFO) mode.
• Enter [4][3][2][5][6][2][5] [0] on the numeric keypad.

◎In VFO mode, VFO will be displayed on the right. Any transmission is prohibited, and reception and scanning are allowed.
Among them, the scanning frequency can be accurately set.

WARNING: Just because you can program in a channel does not mean you’re automatically authorized to use that frequency. Transmitting on frequencies you’re not authorized to operate on is illegal, and in most jurisdictions a serious offence. However, it is legal in most jurisdictions to listen. Contact your local regulatory body for further information on what laws, rules and regulations apply to your area.

Channel (MR) mode

• The use of Channel (MR) mode is dependent on actually having programmed in some channels to use.
• Once you have channels programmed and ready, you can use the / keys or the encoder to navigate between channels.

◎In MR mode, the channel number will be displayed on the right. Among them, GMRS communication (CH1-CH30) allows transmission and reception. Channels other than CH01-CH30 can only be scanned and received, and transmission is prohibited.

ADVANCED FEATURES

Frequency scanning

This function can scan the frequency.

• In frequency mode, press 【*SCAN】key for more than 2 seconds. The radio will start scanning the frequency according to the set frequency step.
• Press 【EXIT】key to stop the scanning.

Note: for Scan mode, see Menu No.17.

Channel scanning

Use scan to search the channels for transmissions from unknown parties, to find someone in your group who has accidentally changed channels or to quickly find unused channels for your own use.

• In channels mode, press 【*SCAN】key for more than 2 seconds. The radio will start scanning according to the channel you set.
• You can change the scanning direction with the / keys.
• Press EXIT key to stop scanning.

CTCSS scanning

The function allows scanning the frequencies with CTCSS tone enabled.

• In standby mode, press [MENU] [2][8], “SEEK 67.0” will appear on the display.
• Press [MENU] and the scan of CTCSS tones will start.

NOTES: The function cannot be activated when the radio is set in Channel mode. The Scan will start only when the receiving band will detect a signal.

DCS scanning

This function allows scanning the frequencies with DCS code enabled.

• In standby mode, press [MENU][2][9]; the display will show “SEEK D023N”.
• Press [MENU] and the scan of DCS codes will start.

NOTES: The function cannot be activated when the radio is set in Channel mode. The Scan will start only when the receiving band will detect a signal.

Keypad lock

• This function locks the keypad to prevent accidental pressure of the controls.
• To unlock the keypad, press [* ] for more than 2 seconds.

FM Radio (FM)

The frequency range to listen to the radio is 76-108MHz.

• In frequency or channel mode, Press [FM/SOS] to turn on the radio.
• Select the desired radio frequency with the / keys or input the frequency.
  • Press [*SCAN] to automatically search a radio station.
• Press [FM/SOS] to exit FM radio.

Note: while you are listening to the radio, the frequency or channel of A / B receiving signal will automatically switch to the frequency or channel mode for normal transmitting and receiving. When the signal disappears the radio will automatically switch again to FM radio mode.

TX 1000Hz, 1450Hz, 1750Hz, 2100Hz repeaters tone

• Press [PTT] + [LAMP/Monitor] to send 1750Hz repeaters tone. This function is useful for communications through repeaters.
• If you have the keypad lock enabled on your radio, you can still send a 1750Hz tone the regular way without having to unlock your radio.

Manual Programming (Channels Memory)

Memory channels are an easy way to store commonly used frequencies so that they can easily be retrieved at a later date. The radio features 199 memory channels that each can hold: Receive frequencies, group signaling information, bandwidth, ANI/ PTT-ID settings and a six character alphanumeric identifier or channel name 1 .

Frequency Mode vs. Channel Mode

In standby mode, press and hold the [VFO/MR] key to switch between frequency (VFO) mode and channel (MR) mode.
These two modes have different functions and are often confused.

• Frequency Mode (VFO): Used for a temporary frequency assignment, such as a test frequency or quick field programming if permitted.
• Channel Mode (MR): Used for selecting preprogrammed channels.

Ex 1. Programming a Scan Channel with CTCSS Tone

1. EXAMPLE: New memory in Channel 31:
   • RX = 432.55000 MHz
   • TX: CTCSS tone 123.0

• Press the [EXIT] button to switch between menus.
• Press and hold the [VFO/MR] key to set the radio to VFO mode, and the VFO icon is displayed on the right.
• [MENU] [2][6]: Deletes Prior Data in channel (Ex. 31)
• [MENU] [1][1] [MENU]123.0 [MENU] [EXIT]: Selects desired RX encode tone
• Enter RX frequency (Ex. 43255000)
• [MENU] [2][7] [MENU] [3][1] [MENU]: Enter the desired channel (Ex 31)
  • – >>[EXIT]: RX has been added
• Press [VFO/MR] key to return to the MR mode and the channel number will reappear.

Ex 2:  Channel memory for scanning frequency

1. EXAMPLE: New memory in Channel 31:
   • Scans frequency ranger 430-435MHz
   • RX = 432.55000 MHz
   • RX: DCS D023N

• Press the [EXIT] button to switch between menus.
• Press and hold the [MENU] key to set the radio to VFO mode, and the VFO icon is displayed on the right.
• [MENU] [1][7] [MENU]: Enter the scan range menu
• Enter [4][3][0][4][3][5] [MENU] [EXIT]: Enter the scan frequency range
• *Press and hold the [ SCAN] key to start frequency:** Frequency required for scanning scan, 432.55000 frequency points start to scan.
  • There is activity, stay here temporarily, press [PTT] key to stop scanning, confirm the required frequency.
  • Stop scanning, the required storage frequency
• [MENU] [10] [MENU] [1] [MENU] [EXIT]: Select desired RX encode sub tone (Ex D023N DCS)
• [MENU] [2][8]: Deletes Prior Data in channel (Ex. 31)
• [MENU] [2][7] [MENU] [3][1] [MENU]: Enter the desired channel (Ex 31)
  • – >> [EXIT]: Channel has been added
• Press and hold the [MENU] key to return to the MR mode and the channel number will reappear.

Built-in LED Flashlight

• Press the flashlight button to turn and keep the light on. Press the flashlight button again, the light is off.

NOAA weather Receiver /Scan

• Your radio can tune in to broadcasts by the United States National Oceanic and Atmospheric Administration (NOAA) Weather Radio and Environment Canada Weather Radio.
• Your radio has a NOAA weather receiver function, to enable the user to receive weather reports from designated NOAA stations.

Note: NOAA weather radio stations are assigned to cover specific areas and service may be limited. Please check with your local weather office for frequency and details or visit www.weather.gov/nwr in the US to view the appropriate transmitter for your area. When you listen to a weather channel, you cannot use your radio in scan mode or for GMRS communications.

Bluetooth Programming

Step 1: Download Odmaster App

Step 2: Register an account and log in

Tips: It is recommended to register by email or log in directly by Facebook

Step 3: Connect bluetooth and radio in app

Tips

After the phone is turned on Bluetooth, do not paired the device with your phone in BT settings, just make sure that BT is enabled and then open the Odmaster App and pair with the programmer within the App.

Step 4: Select model and read from radio

PC Programming

• Odmaster Web allows you to set parameters on the web page.
• After saving, it will be synchronized to the mobile phone and can be directly written to the radio.
• Compared with the mobile phone page, the web page is more comfortable, convenient and faster.

Sign in your account on Odmaster Web

• (https://web.odmaster.net)

WORKING THE MENU SYSTEM

For a complete reference on available menu items and parameters, see Appendix C, Shortcut Menu operations.

Note: in channel mode, the setting of these features is not possible: CTCSS/ DCS tones, wide/narrow bandwidth, PTT-ID, Busy channel lock out, channel name edit.

Basic use

Using the menu with arrow keys

• Press the [MENU] key to enter the menu.
• Use the / keys to navigate between menu items.
• Once you find the desired menu item, press [MENU] again to select that menu item.
• Use the / keys to select the desired parameter.
• When you’ve selected the parameter you want to set for a given menu item;
  • To confirm your selection, press [MENU] and it will save your setting and bring you back to the main menu.
  • To cancel your changes, press [EXIT] and it will reset that menu item and bring you out of the menu entirely.
• To exit out of the menu at any time, press the [EXIT] key.

Using short-cuts

As you may have noticed if you looked at Appendix C, Shortcut Menu operations, every menu item has a numerical value associated with it. These numbers can be used for direct access of any given menu item.
The parameters also have a number associated with them; see Appendix C, Shortcut Menu operations for details.

Using the menu with short-cuts

• Press the [MENU] key to enter the menu.
• Use the numerical keypad to enter the number of the menu item.
• To enter the menu item, press the [MENU] key.
• For entering the desired parameter you have two options:
  • Use the arrow keys as we did in the previous section; or
  • Use the numerical keypad to enter the numerical short-cut code.
• And just as in the previous section;
  • To confirm your selection, press [MENU] and it will save your setting and bring you back to the main menu.
  • To cancel your changes, press [EXIT] and it will reset that menu item and bring you out of the menu entirely.
• To exit out of the menu at any time, press the [EXIT] key.
• All further examples and procedures in this manual will use the numerical menu shortcuts.

Functions and operations

Squelch level (Squelch) – MENU No.0

Thanks to this function you can adjust the squelch in 10 different levels:

• Level 0: opened squelch. With this setting, radio will detect all signals, also the weakest ones, but will also receive the background noise or undesired signals.
• Levels 1- 9: level 1 (lowest squelch level), level 9 (highest squelch level).
  • If the squelch is set to the highest level, the radio will receive the strongest signals only.

Step frequency (Step) – MENU No.1

• This function lets you select the desired frequency step.
• The selectable steps are the following: 2.5/5.0/6.25/10.0/12.5/20.0/25.0/50.0 KHz

Note: in channel mode, this function cannot be modified.

TX Power – MENU No.2

• This function lets you select the three different power output according to using scenario.

Power save (Power Save) – MENU No.3

• The power save feature enables a reduction in the consumption of the battery when the radio is in standby.
• You have 5 selections available: Off/ Mode 1/ Mode 2/ Mode 3/ Mode 4. For example: Mode 1= 1s’ working and 1s’ battery saving. Mode 2= 1s’ working and 2s’ battery is saving.

NOTE: The higher the number the longer the battery lasts. The higher number increases the RX sleep cycle, but you may miss the first few syllables before the RX opens.

VOX Function (Vox Level ) – MENU No.4

This function allows hands-free conversations: just speak in the direction of the microphone and the communication will be automatically activated.
You can choose amongst 11 levels: Off, 1-9. 1 is the highest level, 9 is the lowest one. If this option is set to Off, the VOX function is turned off

Note: the higher is the level, the higher is the microphone sensitivity. The VOX function cannot be modified in SCAN and FM radio mode.

Wide/Narrow bandwidth (Bandwidth) – MENU No.5

This function is used to set the working bandwidth of the radio.
You can choose between wide or narrow bandwidth.

• Wide: 25KHz
• Narrow: 12.5KHz

Note: In channel mode, this function cannot be modified.

Backlight (Backlight) – MENU No.6

• With this function you can adjust the auto off time of the display backlight (Bright, 1-10Sec).
• When the option is Bright, the backlight is always on, which will affect the battery standby time.

Note: we suggest you setting 4-5s levels.

Dual Watch Operation (D.Wait) – MENU No.7

• When this function is activated, you can receive the frequency of channel A and channel B at the same time.
• If a signal is detected, the▼/▲ pointer will blink on the corresponding channel or frequency.

Note: In Dual Watch operation mode, you can change the parameter of AB channel or frequency freely.

Keypad beep (Beep) – MENU No.8

• When this function is enabled, every time a button is pressed, you will hear a beep tone.

Time-Out-Timer (TOT) – MENU No.9

• The TOT function is used to prevent a too long transmission and limits the tx time: TOT temporarily stops the transmission if the radio has been used beyond the max pre-set time (for example 15s, 30s, 45s, etc).

Note: If this option is set to OFF, press and hold the PTT key to keep transmission.

Receiving DCS (Rx DCS) – MENU No.10

DCS codes are similar to access codes and can be added to channels, so as to create a sort of personal channel. They enable the radio to communicate with the users that are tuned on the same channel and have set the same DCS code.

You can choose amongst:

• Off: Off
• D023N-D754N (Normal DCS), D023I-D754I (Inverse DCS)

Note: In radio there are 208 groups of normal and inverse DCS codes. This function cannot be amended in channel mode.

Receiving CTCSS (Rx CTCSS) – MENU No.11

• As DCS codes, the CTCSS codes can be added to the channels for creating new private channels.

Note: there are 50 groups of CTCSS tones. In channel mode the CTCSS tones cannot be changed.

Transmitting DCS (Tx DCS) – MENU No.12

• In this Menu you activate DCS codes in tx mode. You can choose between normal R-DCS (D023N-D754N) and inverted R-DCS (D023I-D754I)

Note: the groups of DCS codes are 208. DCS codes cannot be changed in channel mode.

Transmitting CTCSS (Tx CTCSS) – MENU No.13

• In this Menu you can set a CTCSS tone in tx mode.
• You can choose: Off or CTCSS (67.0 to 254.1 Hz)

Note: there are 50 groups of CTCSS tones. In channel mode the CTCSS tones cannot be changed.

Voice prompts function (Voice) – MENU No. 14

• With this function, you activate a voice that informs you about any operation/ selection you are doing.

TX-SEL – MENU No. 15

• Transmit on MAIN Channel
• Transmit on MOST RESENT receive channel

Scan Add (Scan Add) – MENU No.16

In channel mode, to scan the current channel, the channel must be added to the scan group.

• On: Turn on the scan function of the current channel.
• Off: Do not scan the current channel.

SCAN Resume Mode (Scan Mode) – MENU No.17

Thanks to this function, radio can SCAN in frequency or channel mode. You can choose amongst three options:

• Time-operated SCAN
  • Whenever a signal is detected, the radio will suspend the SCAN for 5 seconds, and then will continue to SCAN even if the signal is still present.
• Carrier-operated SCAN
  • Whenever a signal is detected, the radio will stop scanning. It will resume to SCAN once the signal will disappear.
• Search -Search SCAN
  • The radio will stop scanning once a signal is detected.

FM Dual Watch (FM-DW) – MENU No.18

Channel A Display Mode (MDF-A) – MENU No.19

This function is used to set the display mode of channel A.
Display modes:

• Frequency: Frequency + channel No.
• NAME: Channel name

Note: Channel name mode must be set by the programming software. Up to three numbers or characters can be edited.

Channel B Display Mode (MDF-B) – MENU No.20

This function is used to set the display mode of channel B.
Display modes:

• Frequency: Frequency + channel No.
• NAME: Channel name
  

Note: Channel name mode must be set by the programming software. Up to three numbers or characters can be edited.

Busy Channel Lock (Busy Lockout) – MENU No. 21

• When this function is on, it may prevent other radios’ interference. If the selected channel is being used by other radios,when you press key PTT, your radio cannot transmit.
• Release the PTT and transmit as soon as the frequency is no longer busy

Auto Keypad Lock (AUTO LK) – MENU No.22

• When this feature is activated, the keypad will be automatically locked after 15s; this prevents accidental pressure of any keys.
• The keypad lock can be manually activated/deactivated through the keypad: keep pressed [* ] .

Frequency offset direction (Direction) – MENU No.23

Using this function, you can set the direction of the frequency offset in rx and tx.
You have the following options:

• Plus: Positive offset;
• Minus: Negative offset;
• None: None offset.

Note: you should set different frequency deviation according to the repeaters selected. This function is not enabled in channel mode.

Frequency offset (Offset) – MENU No. 24

• In this MENU you can set the deviation between tx and rx. The frequency offset of this radio is 00.000-99.998MHz.

Channel store – (Memory) – MENU No. 25

• When the radio is in frequency working mode or standby mode, input the desired frequency or parameters directly.

NOTES: If you want to set CTCSS tones, DCS codes or the frequency offset, you have to do it before storing the channel. The channels already stored are displayed as CH-XXX (“CH” and -channel number), and other channels only display channel numbers.

Channel Delete (Delete) – MENU No.26

• In this menu you can delete a channel of the radio.

Alarm Mode (Alarm Mode) – MENU No.27

This function can set the tone alarm/code alarm/site alarm of the radio.
Keep pressed the [FM/SOS] key for 3 seconds to start the alarm tone.
The following three options can be selected:

• Site: the speaker emits an alarm tone but the radio doesn’t transmit;
• Tone: the speaker emits an alarm tone and the radio transmits it;
• Code: the speaker emits an alarm tone and the radio transmits it followed by ANI-ID code.

Scan of frequencies with CTCSS (SEEK CTC) – Menu No. 28

• The function allows scanning the frequencies with CTCSS tone enabled.

NOTES: The function cannot be activated when the radio is set in Channel mode. The Scan will start only when the receiving band will detect a signal.

Scan of frequencies with DCS (SEEK DCS) – Menu No. 29

• This function allows scanning the frequencies with DCS code enabled.

NOTES: The function cannot be activated when the radio is set in Channel mode. The Scan will start only when the receiving band will detect a signal.

Squelch tail elimination (TAIL) – Menu No. 30

• This function is used eliminate squelch tail noise between handhelds that are communicating directly (no repeater). Reception of a 55 Hz or 134.4 Hz tone burst mutes the audio long enough to prevent hearing any squelch tail noise.

Roger beep (ROGER) – Menu No. 31

• When the PTT is released, the radio will beep to confirm to other users that you have finished your transmission and that they can start talking.

1750Hz Repeater Tone (R-TONE) – Menu No.32

• With this function you can select 1000Hz, 1450Hz, 1750Hz, 2100Hz repeater tone. To send out a repeater tone; You hold down the [PTT] + [SK2] key.
• If you have the keypad lock enabled on your radio, you can still send a 1750Hz tone the regular way without having to unlock your radio.

Language selection (Language) – Menu No. 33

• With this function, you can select the language of the LCD display and operation prompt.

Frequency hopping system (Hopping RX) – MENU No. 34

• With this function, you can activate the frequency hopping system, improve the anti-interference ability of the radio, and

Reset (Reset) – Menu No.40

With this function you can reset the transceiver to the factory-programmed settings and parameters. After that, you can set the desired functions.

There are two types of reset:

• VFO: Menu Reset
• ALL: Menu and channel Reset reduce the risk of being monitored.

Dual Band single display (SYNC) – Menu No.36

The radio is dual-band, dual-display, and the screen can display A/B frequency band at the same time. It can also be set to dual-band single-screen display. When single frequency point is displayed, the channel nickname, frequency and channel number will be displayed at the same time.

• On: Turn on the SYNC function and display the alias, frequency and channel number of the current channel.
• Off: Turn off the SYNC function, which is a dual-segment dual display mode. The main frequency and sub frequency will be displayed.

PTT-ID (PTT-ID) – MENU No.37

With this function you can decide when sending the ANI-ID code in tx mode.
You can choose amongst 4 possibilities.

• Off: press PTT to turn it off
• BOT: the code is sent when you press the PTT
• EOT: the code is sent when the PTT is released
• BOTH: the code is sent when you press and release the PTT

Note: select ‘OFF’ when using in case of affecting the radio.

DTMFST (DTMFST) – MENU No.38

Determines when DTMF Side Tones can be heard from the transceiver speaker. You can choose amongst four options:

• Off: No DTMF Side Tones are heard
• DT-ST: Side Tones are heard only from manually keyed DTMF codes
• ANI-ST: Side Tones are heard only from automatically keyed DTMF codes
• DT+ANI: All DTMF Side Tones are heard

ANI-ID (ANI-ID) – MENU No.39

• With this function you can set your ID-code. It can be programmed by the proper programming software. You can edit up to 5 digits.

Squelch tail elimination of repeater (RP-STE) – Menu No. 40

This function is used when the radio operates through a repeater; when the PTT is released, the repeater will emit the end transmission tone to confirm it is working.

• Available settings:
  • Off, 1,2,3,4,5,….10 to set the delay time.

_ Note: _Please disable this function in normal using, lest affect your normal conversation.

Delay the squelch tail of repeater (RPT-RL) – Menu No.41

• With this function you have the confirmation that the repeater has transferred the signal. You can choose amongst: Off 1,2,3,4,5,….10 to set the delay time.

Appendix A

Appendix A. – Trouble shooting guide

You cannot turn on the radio.

| The battery may be installed improperly.| Remove and reattach the battery.
The battery power may run out.| Recharge or replace the battery.
The battery may suffer from poor contact caused by dirty or damaged battery contacts.| Clean the battery contacts or replace the battery.

During receiving, the voice is weak or intermittent.

| The battery voltage maybe low.| Recharge or replace the battery.
The volume level may be low.| Increase the volume.
The antenna maybe loose or maybe installed incorrectly.| Turnoff the radio, and then remove and reattach the antenna.
The speaker maybe blocked.| Clean the surface of the speaker.
You cannot communicate with other group members.| The frequency or signaling type maybe inconsistent with that of other members.| Verify that your TX/RX frequency and signaling type are correct.
You may be too far away from other members.| Move towards other members.

You hear unknown voices or noise.

| You may be interrupted by radios using the same frequency.| Change the frequency, or adjust the squelch level.
The radio in analog mode maybe set with no signaling.| Request your dealer to set signaling for the current channel to avoid interference

You are unable to hear anyone because of too much noise and hiss.

| You may be too far away from other members.| Move towards other members.
You may be in an unfavorable position. For example, your communication may be blocked by high buildings or blocked in an underground area.| Move to an open and flat area, restart the radio, and try again.
It may be the result of external disturbance (such as electromagnetic interference).| Stay away from equipment that may cause interference.
The radio keeps transmitting.| VOX may be turned on or the headset is not installed in place| Turn off the VOX function. Check that the headphones are in place.

NOTE: If the above solutions cannot fix your problems, or you may have some other queries, please contact your dealer for more technical support.

Appendix B

Appendix B. – Technical Specifications

General

• Frequency Range: GRSM(RX & TX)
  • 136-174 & 400-512MHz(RX)
• Memory Channel: 30 GMRS+11 NoAA weather Channels+158 Scanner
• Operation Voltage: DC 7.4 V ±10%
• Battery Capacity: 1500mAh (Li-Ion)
• Frequency Stability: ±2.5ppm
• Operating Temperature: -20℃ to +50℃
• Mode of Operation: Simplex
• Antenna Impedance: 50ohm

Transmitter Part

• RF Output Power: ≤5W(GMRS)
• FM Modulation: 11K0F3E@12.5KHz
• Adjacent Channel Power: 60dB @ 12.5KHz
• Transmission current: ≤1500mA

Receiver Part

• Receive Sensitivity: 0.25μV (12dB SINAD)
• Adjacent Channel Selectivity: ≥55dB@12.5KHz
• Inter Modulation and Rejection: ≥55dB@12.5KHz
• Conducted Spurious Emission: ≤-57dB@12.5KHz
• Rated Audio Power Output: 1W @16 ohms
• Receive current: ≤380mA
• Rated Audio Distortion: ≤5%

NOTE: All specifications may be modified without prior notice or liability. Thank you.

Appendix C

Appendix C. – Shortcut Menu operations

Appendix D. – GMRS Frequency Chart (MHz)

CH.No| CH.Freq.| Type of Radio| Power Output| CH.No| CH.Freq.| Type of Radio| Power Output
---|---|---|---|---|---|---|---
1| 462.5625| GMRS| High| 16| 462.5750| GMRS| High
2| 462.5875| GMRS| High| 17| 462.6000| GMRS| High
3| 462.6125| GMRS| High| 18| 462.6250| GMRS| High
4| 462.6375| GMRS| High| 19| 462.6500| GMRS| High
5| 462.6625| GMRS| High| 20| 462.6750| GMRS| High
6| 462.6875| GMRS| High| 21| 462.7000| GMRS| High
7| 462.7125| GMRS| High| 22| 462.7250| GMRS| High
8| 467.5625| FRS| Low| 23| 467.5500/462.5500| RPT| High
9| 467.5875| FRS| Low| 24| 467.5750/462.5750| RPT| High
10| 467.6125| FRS| Low| 25| 467.6000/462.6000| RPT| High
11| 467.6375| FRS| Low| 26| 467.6250/462.6250| RPT| High
12| 467.6625| FRS| Low| 27| 467.6500/462.6500| RPT| High
13| 467.6875| FRS| Low| 28| 467.6750/462.6750| RPT| High
14| 467.7125| FRS| Low| 29| 467.7000/462.7000| RPT| High
15| 462.5500| GMRS| High| 30| 467.7250/462.7250| RPT| High

Appendix E. – DCS Table

DCS CODE LIST

Number| Code| Number| Code| Number| Code| Number| Code| Number| Code
---|---|---|---|---|---|---|---|---|---
1| D023N| 2| D025N| 3| D026N| 4| D031N| 5| D032N
6| D036N| 7| D043N| 8| D047N| 9| D051N| 10| D053N
11| D054N| 12| D065N| 13| D071N| 14| D072N| 15| D073N
16| D074N| 17| D114N| 18| D115N| 19| D116N| 20| D122N
21| D125N| 22| D131N| 23| D132N| 24| D134N| 25| D143N
26| D145N| 27| D152N| 28| D155N| 29| D156N| 30| D162N
31| D165N| 32| D172N| 33| D174N| 34| D205N| 35| D212N
36| D223N| 37| D225N| 38| D226N| 39| D243N| 40| D244N
41| D245N| 42| D246N| 43| D251N| 44| D252N| 45| D255N
46| D261N| 47| D263N| 48| D265N| 49| D266N| 50| D271N
51| D274N| 52| D306N| 53| D311N| 54| D315N| 55| D325N
56| D331N| 57| D332N| 58| D343N| 59| D346N| 60| D351N
61| D356N| 62| D364N| 63| D365N| 64| D371N| 65| D411N
66| D412N| 67| D413N| 68| D423N| 69| D431N| 70| D432N
71| D445N| 72| D446N| 73| D452N| 74| D454N| 75| D455N
76| D462N| 77| D464N| 78| D465N| 79| D466N| 80| D503N
81| D506N| 82| D516N| 83| D523N| 84| D526N| 85| D532N
86| D546N| 87| D565N| 88| D606N| 89| D612N| 90| D624N
91| D627N| 92| D631N| 93| D632N| 94| D645N| 95| D654N
96| D662N| 97| D664N| 98| D703N| 99| D712N| 100| D723N
101| D731N| 102| D732N| 103| D734N| 104| D743N| 105| D754N
---|---|---|---|---|---|---|---|---|---
106| D023I| 107| D025I| 108| D026I| 109| D031I| 110| D032I
111| D036I| 112| D043I| 113| D047I| 114| D051I| 115| D053I
116| D054I| 117| D065I| 118| D071I| 119| D072I| 120| D073I
121| D074I| 122| D114I| 123| D115I| 124| D116I| 125| D122I
126| D125I| 127| D131I| 128| D132I| 129| D134I| 130| D143I
131| D145I| 132| D152I| 133| D155I| 134| D156I| 135| D162I
136| D165I| 137| D172I| 138| D174I| 139| D205I| 140| D212I
141| D223I| 142| D225I| 143| D226I| 144| D243I| 145| D244I
146| D245I| 147| D246I| 148| D251I| 149| D252I| 150| D255I
151| D261I| 152| D263I| 153| D265I| 154| D266I| 155| D271I
156| D274I| 157| D306I| 158| D311I| 159| D315I| 160| D325I
161| D331I| 162| D332I| 163| D343I| 164| D346I| 165| D351I
166| D356I| 167| D364I| 168| D365I| 169| D371I| 170| D411I
171| D412I| 172| D413I| 173| D423I| 174| D431I| 175| D432I
176| D445I| 177| D446I| 178| D452I| 179| D454I| 180| D455I
181| D462I| 182| D464I| 183| D465I| 184| D466I| 185| D503I
186| D506I| 187| D516I| 188| D523I| 189| D526I| 190| D532I
191| D546I| 192| D565I| 193| D606I| 194| D612I| 195| D624I
196| D627I| 197| D631I| 198| D632I| 199| D645I| 200| D654I
201| D662I| 202| D664I| 203| D703I| 204| D712I| 205| D723I
206| D731I| 207| D732I| 208| D734I| 209| D743I| 210| D754I

Appendix F:  – CTCSS Table

CTCSS CHART (Hz)

Number| Frequency| Number| Frequency| Number| Frequency| Number| Frequency| Number| Frequency
---|---|---|---|---|---|---|---|---|---
r| y| r| y| r| y| r| y| r| y
1| 67.0| 2| 69.3| 3| 71.9| 4| 74.4| 5| 77.0
6| 79.7| 7| 82.5| 8| 85.4| 9| 88.5| 10| 91.5
11| 94.8| 12| 97.4| 13| 100| 14| 103.5| 15| 107.2
16| 110.9| 17| 114.8| 18| 118.8| 19| 123.0| 20| 127.3
21| 131.8| 22| 136.5| 23| 141.3| 24| 146.2| 25| 151.4
26| 156.7| 27| 159.8| 28| 162.2| 29| 165.5| 30| 167.9
31| 171.3| 32| 173.8| 33| 177.3| 34| 179.9| 35| 183.5
36| 186.2| 37| 189.9| 38| 192.8| 39| 196.6| 40| 199.5
41| 203.5| 42| 206.5| 43| 210.7| 44| 218.1| 45| 225.7
46| 229.1| 47| 233.6| 48| 241.8| 49| 250.3| 50| 254.1

Appendix G:  NOAA Weather Radio Frequency List (US, CAN)

• Channel 8, 9 are designated Canadian Marine Frequencies

Disclaimer

The Company endeavors to achieve the accuracy and completeness of this manual, but no warranty of accuracy or reliability is given. All the specifications and designs are subject to change without notice due to continuous technological development.
No part of this manual may be copied, modified, translated, or distributed in any manner without the prior written consent of the Company.
We do not guarantee, for any particular purpose, the accuracy, validity, timeliness, legitimacy or completeness of the third-party products and contents involved in this manual.

E-mail: amz@tidradio.com
http://www.amazon.com/tidradio
Visit www.amazon.com/tidradio for more products

References

• TIDRADIO

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>