Alfred DB1S-BL Wifi Bluetooth Electronic Deadbolt Lighted Keypad

Touchscreen Smart Lock

Product Information

The DB1S-BL is a deadbolt lock designed for use on doors. It features a drive- in collar and a Phillips screwdriver for installation.

Specifications

• Backset: 2-3/8″ or 2-3/4″
• Latch Hole Depth : 1″ (25 mm)

Product Usage Instructions

1. Step 1: Insert Latch Bolt
   Temporarily insert the latch bolt into the door. If it cannot be inserted all the way to the end, you need to extend the latch hole. Proceed to Step 2. If the latch bolt sits properly, skip to Step 3.

2. Step 2 (Optional): Extend Latch Hole
   If you need to extend the latch hole, use a 1″ (25 mm) boring bit to extend it to the correct depth based on your backset. For a 2-3/8″ backset, extend the latch hole to 3-7/16″. For a 2-3/4″ backset, extend it to 3-13/16″. Insert the latch bolt again to verify the fit.

3. Step 3: Test Latch Bolt Operation
   Use a screwdriver to extend and retract the bolt to check its operation. If it doesn’t rotate smoothly due to a small face bore hole, proceed to Step 4 for chiseling. If the bolt operates smoothly, skip to Step 5.

4. Step 4 (Optional): Chisel Out a Channel
   If the latch bolt operation is not smooth, chisel out a small channel at the top of the hole to allow for smooth rotation. Test the latch bolt operation again after chiseling.

5. Step 5: Install Latch Bolt and Strike
   Install the latch bolt and strike on the door and door jamb respectively.

FAQ (Frequently Asked Questions)

• Q: What is the backset measurement for this deadbolt lock?
  • A: The backset options for this lock are 2-3/8″ or 2-3/4″.
• Q: How deep should the latch hole be?
  • A: The latch hole should be 1″ (25 mm) deep.
• Q: What should I do if the latch bolt doesn’t rotate smoothly?
  • A: If the latch bolt doesn’t rotate smoothly, you may need to chisel out a small channel at the top of the hole for smooth rotation. Refer to Step 4 for chiseling instructions.

Specifications

Outside escutcheon

Status Indicators

1. Unlocked, or setting succeed.
2. Locked, or setting failed.
3. Low battery Warning

Inside escutcheon

Components

Preparing for Installation

Tools Needed

Lock Installation

2 Phillips screwdriver

Door prep (Optional Tools, only required if installing lock on new door without existing Lock Prep)

1. 2-1/8″ (53mm) hole saw
2. 1″ (26mm) boring bit
3. 7/64″ (2.5mm) drill bit
4. 3/8″ (10mm) drill bit
5. Chisel & Hammer

IMPORTANT
The handing switch needs to be put in the direction the deadbolt is sliding when looking at the inside of your door.

PREPARE LOCK FOR INSTALLATION

Unpack the Lock

• Inside escutcheon Confirm door handing direction.
  • There is a switch on back side of the Inside escutcheon. Position of the switch should be towards the door frame (see picture at right) when installed.
• Deadbolt Bolt Confirm Backset measurement
  • Note : Bolt ships with backset in 2-3/8″ position. If required, turn the bolt case and pull to extend to 2-3/4″ backset position. (See picture below.) A The bolt must be in retracted (Unlocked) position when you are changing backset.
• Outside Escutcheon Remains assembled.

Installation

1. Temporarily insert latch bolt.
   If your latch bolt cannot be inserted all the way to the end, you need to extend the latch hole. Follow the instruction in Step 2. If the latch bolt sits properly, skip to Step 3. NOTE : The bolt must be in retracted (Unlocked) position when installing the lockset.

2. (OPTIONAL). If you do not need to extend the latch hole, go to Step 3.

   • Use a 1’’ (25 mm) boring bit to extend the latch hole to the correct depth based on your backset. For 2-3/8’’ backset: 3-7/16”
   • For 2-3/4’’ backset: 3-13/16”
   • Then insert the latch bolt again to verify the fit.

3. Test latch bolt operation.

   • Use a screwdriver to extend and retract bolt to check the operation. If it doesn’t rotate smoothly because the face bore hole is too small, you need to chisel out a small channel at the top of the hole for smooth rotation.
   • Follow the instruction in Step 4 for chiseling. If the bolt operates smoothly, skip to Step 5.

4. (OPTIONAL). If the latch bolt operation is smooth, skip to Step 5.

   • Chisel out a channel. Then test the latch bolt opera-tion again.

5. Install latch bolt and strike on the door.
   NOTE : Make sure to allow for the bolt to be centered in the strike .

6. Hold the outside escutcheon with Keypad, flush to your door and align tailpiece and cable with door hole prep. Pass Cable through door UNDER latch bolt.

   • The 3rd Top Post is OPTIONAL. The Top Post is used for additional security, or when a door is weak or warped. The Top Post can be easily removed by unscrewing with a pair of pliers and discarded. As you position the outside escutcheon, route the cable through 2-1/8″ diameter hole.
   • NOTE : Cable must go through door hole under the bolt.
   • NOTE : Bolt must be in retracted (unlocked) position.

7. Position the inside mounting plate by first routing the cable and connector through the mounting plate’s cable hole.

8. Secure both assemblies using 3 #8-32*30 screws, making sure that outside escutcheon is vertically aligned. Tighten securely with a #2 Phillips screwdriver.

9. Place the rotation shaft key tailpiece into the hole on the inside escutcheon plate. The tailpiece should be in the horizontal position. NOTE : Tail piece must be in the horizontal position when properly installed.

10. Attach cable assembly to the inside escutcheon PCB by lining up notches on top of cable connector to slots on PCB connector. Press connector in firmly using thumbs until completely seated.

11. Install inside escutcheon on inside mounting plate.

12. NOTE : The horizontal orientation of the tailpiece as you insert the inside escutcheon (thumb turn should be vertical)

13. Secure using screws through the inside escutcheon onto the mounting plate.

14. NOTE : Test operation using thumb turn before installing batteries to make sure latch bolt extends smoothly. If latch bolt does not extend, please check that the tail piece was inserted correctly

15. Insert four AA alkaline batteries. Front Keypad will light up to confirm proper installation. Then install battery cover plate.

Congratulations, you have installed the Alfred DB1S Touch Screen Smart Deadbolt! Please now download the Alfred Home App from either Apple APP store or Google Play Store to set up your Master PIN Code for the lock or refer to Programming Instructions booklet provided.

Download the Alfred Home App

For support, please reach out to: support@alfredinc.com You can also reach us at 1-833-4-ALFRED (253733) www.alfredlocks.com

References

• Alfred Smart Locks – Making your smart home smarter

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>