ATrack AW500 Smart Al Camera Installation Guide

ATrack AW500 Smart Al Camera

Product Information

Specifications

• Product Name: ATrack AW50
• Compatibility: iPhone (Android version coming soon)

Product Usage Instructions

Viidure App Installation and Preparation

1. Download and install the Viidure App from the App Store on your iPhone.
2. Please note that the Android version does not currently support the ATrack AW50. We are working on releasing a new Android version with support as soon as possible.

Quick Installation Guide

Please follow the steps below to install the ATrack AW50:

1. Step 1: [Insert step 1 instructions]
2. Step 2: [Insert step 2 instructions]
3. Step 3: [Insert step 3 instructions]

ATrack Technology

The ATrack AW50 utilizes innovative ATrack technology to provide advanced tracking capabilities. With this technology, you can accurately monitor and track various aspects of your device.

Frequently Asked Questions (FAQ)

Q: Can I use the ATrack AW50 with an Android device?

• A : Currently, the ATrack AW50 is only compatible with iPhones.
• We are actively working on releasing a new Android version with support.

Mounting Position-Related Regulations

• Note: The following recommendations do not constitute legal advice and should not be relied upon in lieu of consultation with your own advisors.

For Dash Cams in the US

• Federal Motor Carrier Safety Administration (FMCS) regulations permit dash cams to be installed in either of the following positions:
• From the top of the windshield to 8.5 inches below the upper edge of the area swept by the windshield wipers.

For Dash Cams in UK

• To determine camera placement options, the windscreen is divided into zones:
• Zone A: This is a vertical area 29cm wide (for vehicles over 3.5 tons is 35cm), centered on the steering wheel and contained within the swept area of the windscreen.
• Zone B is the remainder of the swept area of the windscreen.
• No part of the dash cam (including the mount and wire) can intrude more than 10mm (1cm) into Zone A and more than 40mm (4cm) into Zone B.

Mounting Position Recommendations

• The AW500 is recommended to be mounted on the upper edge of the windshield directly above the steering wheel, as shown in the red circle inside the picture.
• In order to drive safely and maximize the Al function, the selection of the camera mounting position needs to be based on the following principles:
• Do not block the driver’s line of sight.
• Do not interfere with the driver’s driving.
• The camera should be kept horizontal, not tilted.
• The driver’s face should preferably be in the center of the inside camera preview (available in “Viidure” APP).
• The center point of the camera preview (available in the “Viidure” APP) of the front camera should coincide with the end of the road.

Installation instruction

Memory card installation

4G Card installation

Line connection diagram

LED Indication

Viidure App installation and preparation

• Please download and install the Viidure App from the App Store of your iPhone (The Android version does not currently support this device and we will be releasing a new Android version with support as soon as possible).

Connect to AW500 via App

• Follow the app’s instructions to connect to the Wi-Fi of AW500.
• Note: One AW500 can only be connected to one phone at a time otherwise an error may occur

Camera Settings – Al Settings

• After connecting AW500, press Camera Settings – Al Settings to make sure the ADAS/DMS Renders are turned on.
• Note: If you want the calibration to be more accurate, you can fill in the parameters for the device position in the advanced settings,

ADAS & DMS Calibration

• After the AW500 is connected, the real-time shot will be sent back.
• Note: Both ADAS and DMS calibration will continue only when the movement speed >20km/h, otherwise the calibration progress (0-100%) will pause.

Firmware Upgrade

Method 1: Use the APP to upgrade

1. Prepare a memory card of 16G or more.
2. Insert it into the machine and format it.
3. Put the firmware installation package “SigmastarUpgradeSD.bin” in the root directory of the memory card.
4. Insert the card with the upgrade file into the device.
5. Power the device and turn it on.
6. Connect the device to the app and tap “Camera Settings – Firmware Version”
7. Wait 1-3 minutes, the device will reboot and beep.

The following table shows the LED states when upgrading by APP. Steps 2-5 are the upgrade process, please do not power off or operate the device.

sound
5. Upgrade configuration finished and start recording| Red-(yellow/off)-(green/off)

Method 2: Forced brushing, used in the case of corrupted device firmware

1. Prepare a memory card of 16GB – 128 GB.
2. Insert it into the machine and format it.
3. Put the upgrade file in the root directory of the memory card, including “PL, IPL_CUST, UBOOT, SigmastarUpgradeSD.bin”.
4. Insert the card with the upgrade file into the device.
5. Power up the device and there is no response from the device at this point.
6. Wait 1-3 minutes for the device to power on and beep.

The following table shows the LED states when upgrading by SD card. Steps 2-4 are the upgrade process, please do not power off or operate the device.

2. Poweronthedevice.

Start upgrade/ Upgrade in progress

|

Purple – yellow- green

3. Device Startup and Configuration| Blue – (yellow/off) – (green/off) Power on sound
4. Upgrade configuration finished and start recording| Red-(yellow/off)-(green/off)

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• . Reorient or relocate the receiving antenna.
• • Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void our authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

ISED Statement

This device contains licence-exempt transmitter(s)/receivers) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s).
Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

The digital apparatus complies with Canadian CAN ICES – 3 (B)/NMB – 3(B).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>