MSXTTLY U2C-AIR Wireless Carplay Adapter User Manual

MSXTTLY U2C-AIR Wireless Carplay Adapter User Manual

Precautions

Notice to all users: This wireless Carplay aviator is for converge wired Carplay to a wireless only, supping original car unit which equipped with OEM wired Carplay, and earmarked radios, such as for Sony, Boss, Alpine, Pioneer, JVC, Kenwood, etc.

Notice for Update: Please follow the Upgrade Instruction steps by steps, to avoid some trouble caused by the upgrade failure. It’s unnecessary to upgrade it in most cases, when the adapter works properly.

Connection Diagram

1. Connect to the USB Data Port

NOTE! The adapter should be plugged in a Apple Caplayenabled USB port, when there are multi-USB port in your car.

Connection Steps

2. Activate CarPlay with iPhone

Firmware Update

1. Connect to this ‘smart Box-XXXX’ Wi-Fi device
   *If you have connected to the wireless CarPlay, pls disable your iPhone’s Bluetooth, and join this ‘smartBox-XXXX’ Wi-Fi device at first; Join this [smartBox-xxxx] Wi-Fi device with password ‘88888888’ (Press ‘Connect’ when there is a notification about no internet

2. Press Update
   Enter IP address ‘192.168.1.101’ on Safari browser, slide down the IP setting page, and press ‘Update’ on the bottom of IP setting page.
   NOTE! Please don’t remove the acvatortiunl the light stop flashing. Otherwise, it will get damaged!

3. Forget this Wi-Fi device
   Forget this ‘smartBox-XXXX’ Network after the upgrade finished, and plug the activator back to your car.

Questions & Answers

Q1: There is no sound out while making a phone call.
A: For the Calling problem, it should due to the Bluetooth secondary connection.
You can check whether your iPhone has pressed twice the Bluetooth device ‘smartBox-XXXX’ in ‘Connected’ status in the sings. If yes, then you cannot hear any sound when making a call.
Aer CarPlay entering to the driving mode, all the Bluetooth devices(including smartBox-XXXX Bluetooth device) on the iPhone should show `not connected’, as image.
You can try to forget all the Bluetooth devices in your iPhone’s Bluetooth Seng, and pair the ‘smartBox-XXXX’ again.

Q2: Sometimes won’t connect, car screen freezes in Carplay interface.

• Regarding this connection frozen issue, you can try to optimize the connection by resetting both the iPhone and the car once:

1. Unplug the wireless carplay adapter from USB port first;
2. Reset your car unit audio system;
3. Select the Carplay mode as preference in the vehicle setting i your car has relevant settings;
4. Forget all the Bluetooth devices in your iPhone settings & car unit, (please also check forget the WiFi device ‘smartBox-XXXX’ );
5. Restart your car engine, plug the adapter and pair ‘smartBox-XXXX’ device again. Wireless carplay will resume normal connection. Sometime several times fail carplay connections will change car audio system & iPhone preference, causes data transmission errors. And each time restarting your iPhone & car unit can optimize the CarPlay connection.

If the problem persists, please do not hesitate to contact the `support@proaok.com‘ mail to our technical team. The technician will offer you a more professional solution.

Q3: The sound often cuts out/gets staticky.
A:
Please check whether all Bluetooth devices in iPhone settings (including `smartBox’ and car’s Bluetooth ) display ‘Not Connected’ after switching to CarPlay mode. If not, pls disconnect the connected BT device manually.
There is an Audio streaming mode settings on the IP setting page, you can try to switch to
other modes for your car.
Setting steps:

1. Please connect the iPhone to the box Wi-Fi `smartBox-XXXX’, password: 88888888, then enter the upgrade Safari browser, enter the IP address: 192.168.1.101, and enter the setting page.

2. Switching the Audio streaming mode to
   ‘Mode 1-3’ for your car and press ‘OK’.(As attached image)

3. • Please forget the ‘smartBox-XXXX’ network first after the settings, and relog the wireless activator for the Bluetooth pair.
     Bluetooth 8

Q4: How do I connect to wireless Carplay using another iPhone ?

A: For the multiple iPhones connection, the U2C-Air can remember multiple iPhones which have connected but only will connect the last mobile automatically for wireless Carplay.

When you need to use a 2nd iPhone for connection, it needs to turn off the last mobile’s Bluetooth & Wi-Fi function(or not in the car), and then press the ‘smartBox-XXXX’ Bluetooth device again in your 2nd iPhone Bluetooth setting.

It usually takes 5-15 seconds for the 2nd me connection entering to the wireless CarPlay interface.

Q5: Why Carplay stays connected after getting out of the car ?
A: For some models encountering this issue, it is due to when vehicle engine is turned off, the power supply will remain powered for a short me from the car’s USB data port, the adapter is not set to turn off atomically.

So warless Apple carplay will continue to run for a while then turn off. You can turn off Wi-Fi manually to disconnect wireless Carplay immediately.

Q6: How to get more help when I encounter other connection issues?
A: Please send an email to our official after-sales mail ‘support@proaok.com‘.
Subscripe the issue you have encountered. Further information & photos are helpful for our technicians to identify the cause of the problem:

• Screenshots of the iPhone’s Bluetooth & Wi-Fi Settings
• Photos of the interface displayed on the car screen
• Operating video if available
  If it confirmed by the technicians that the current firmware might doesn’t work well with your car, you can follow the technician’s instruction and fill in your car model & year in the IP(192.168.1.101) setting page.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>