posturite 16306DX Ambidextroas Vertical Mouse User Guide

: June 14, 2024
: POSTURITE

Table of Contents

PRODUCT OWERVEV
WIRED VERSION
BLUETOOTH® / WIRELESS VERSION
BOTH VERSIONS
TROUBLESHOOTING GUIDE
IMPORTANT INFORMATION
ANTIMICROBIAL PROTECTION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

posturite 16306DX Ambidextroas Vertical Mouse User Guide

PRODUCT OWERVEV

A. Left Click
B. Right Click
C. Scroll Wheel
D. Rocker Switch – ‘Bow Tie’ (L/R Hand Switch)
E. DPI and Bluetooth syncing button
F. Bluetooth/OFF/wireless switch
G. USB – USB-C Recharging Cable (Bluetooth/wireless only)
H. 1 x USB Micro Receiver (wireless only)
I. Recharging USB-C Port (Bluetooth/wireless only)
J. Micro Receiver Dongle Housing (Bluetooth/wireless only)

WIRED VERSION

Plug the USB cable into any spare USB port.

BLUETOOTH® / WIRELESS VERSION

For wireless operation
The 2.4 GHz USB micro receiver is located inside the housing on the underneath of the Penguin (J).

Remove the micro receiver and insert into a spare USB port of your computer or laptop. Wait for a short time for your PC to recognise the penguin mouse.
Move switch (F) on the base from ‘OFF’, downwards to the position. The ‘P’ logo will flash GREEN briefly

For Bluetooth® operation
Make sure that your PC is Bluetooth compatible.
To Choose Bluetooth operation.

Move switch (F) on the base from ‘OFF’, upwards to Bluetooth. The ‘P’ logo will flash BLUE briefly.
On your computer turn on ‘Search for Bluetooth’.
Press the DPI/ Bluetooth pair button for 5-10 seconds.
On your PC search for “Penguin 3.0 or 5.0 Mouse”.
Click on “Penguin 3.0 or 5.0 Mouse” and connect.
Your Penguin should now be connected via Bluetooth. If not, press ‘remove ‘Penguin BT 3.0 or 5.0 Mouse’ and repeat same procedure to sync to Bluetooth.

Auto power save
After approximately 20 seconds inactive – Penguin enters power save mode After approximately 30 minutes – Penguin enters deep sleep mode Inactive – click any button to reawaken

Note: It is advised to switch to the ‘OFF’ position if the Penguin is to be transported as this will conserve power.

Rechargeable battery
The Wireless Penguin has an internal rechargeable battery. There may be a certain amount of charge already in the battery.
To fully charge the battery, insert the USB end of the cable (G) into a spare USB port of your computer and the USB-C end of the cable into the front of your mouse (I) see diagram. Refer to the Charging Light Sequence section to indicate the battery level.

Rechargeable battery low power level indicator

Ice Blue light flashing: Low battery (approximately 20% charge remaining)

Charging light sequence

When the charging cable is connected, a series of cultured lights in the illuminated ‘P’ logo will indicate different battery levels.

Penguin in ACTIVE mode:

Orange light + flashing Ice Blue light : Battery charging (below 20% charge)
Orange light + constant Ice Blue light : Battery charging (above a 20% charge)
Ice Blue light only : Battery fully charged

Penguin in INACTIVE mode:

Orange ‘P’ light : Battery charging

Orange ‘P’ light turns off once fully charged.

BOTH VERSIONS

Plug & play
The Penguin Mouse uses Plug & Play technology. No additional software is required.

Right & left handed use
The Penguin is set as a Right Handed mouse by default. To use with your left hand, simply depress the raised section of the rocker switch – ‘Bow Tie’ (D) at the front of the Penguin. This will adjust the direction of the scroll wheel.

Variable DPI [800-1200-1600-2400] – Pointer Speed
The default setting is 800 DPI. To adjust, press and release the DPI button (E) on the base of the Penguin. The illuminated ‘P’ logo will flash to indicate the DPI has been changed.

DPI (pointer speed): Number of Flashes: Speed
800 DPI: 1 ‘P’ Flash: Slow
1200 DPI: 2 ‘PP’ Flash: Medium
1600 DPI : 3 ‘PPP’ Flash: Fast
2400 DPI: 4 ‘PPPP’ Flash: Fastest

Precision scroll wheel with auto scroll
As well as a soft touch and feel Precision Scroll Wheel (C), the Penguin Mouse has an Auto Scroll feature. To activate this, click the Scroll Wheel inwards or downwards and the auto scroll is activated. Move the Penguin forwards or backwards to start auto scrolling at the desired speed. Click the scroll wheel again and the Auto Scroll is stopped

TROUBLESHOOTING GUIDE

Penguin (wired version)

Make sure your Penguin is firmly plugged into your computer’s USB port
Try using a different USB port. If possible plug it directly into the computer i.e. not through any monitors/keyboards/hubs etc.
Although your Penguin is plug & play, make sure your computer is up to date with the latest drivers/operating software for pointing devices
Check that the sensor on the underside of the Penguin isn’t covered and has a clear line of sight to the surface below. Also check that your Penguin has not been dropped which could dislodge the laser.
Try using the Penguin on a mouse mat / non-reflective surface
Close your computer down and reboot

Penguin (Bluetooth/wireless version)
Note: USB is found inside compartment on Penguin base.

Make sure that the Penguin is charged via the USB-C charging cable.
Make sure the switch on the underside of the base is in ‘ON’ position (rechargeable models only) – either ‘UP’ (BLUE) for Bluetooth or ‘DOWN’ (GREEN) for wireless operation.
If using wireless, make sure your Penguin’s dongle (micro receiver) is firmly plugged in to your computer’s USB port.
If using wireless, try unplugging the Penguin dongle (micro receiver), then plugging it back in again.
If using Bluetooth, on your PC, remove Bluetooth item (Penguin Mouse) and readd Bluetooth device again.
If using wireless, try holding the Penguin close to the sensor for 30 seconds whilst intermittently clicking the top button – it sometimes takes this to get the dongle to recognise the hardware.
If using wireless, try using a different USB port to connect your Penguin. If possible plug it directly into the computer, i.e. not through any monitors/ keyboards/hubs etc.
If using wireless, remove the USB Dongle and turn ‘OFF’ the Penguin switch. Reboot your computer. Now re-insert USB dongle, wait 10/15 seconds and turn Penguin switch back ‘ON’ – in ‘DOWN’ (GREEN) position.
Although your Penguin is plug & play, make sure your computer is up to date with the latest drivers / operating software for pointing devices.
Check that the sensor on the underside of the Penguin isn’t covered and has a clear line of sight to the surface below. Also check that your Penguin has not been dropped which could dislodge the laser.
Try using the Penguin on a mouse mat / unreflective surface.
Make sure the charging cable is firmly attached into the USB port of your computer and the USB-C end is firmly pushed into the front of the Penguin. The ‘P’ Logo should light an orange colour. Recharge directly via a USB port on your computer NOT via a multi-USB hub.
Try your Penguin mouse on a different PC/laptop to check if the issue is still present.

If you attempt all of the above suggestions and still there appears to be a problem, please contact your supplier.

IMPORTANT INFORMATION

Health
Long periods of time at your workstation without regular breaks may cause discomfort. Should discomfort persist, see a qualified health professional.

User advice/Maintenance
Try to avoid contact with strong medicated hand creams/sanitizers whilst using the Penguin mouse. Regularly remove dust and dirt build-up from the underneath of your Penguin mouse to ensure a smooth glide movement.

Disclaimer
We make every effort to ensure that the information and procedure in this guide is accurate and complete, no liability can be accepted for any errors or omissions and we reserve the right to make any changes without further notice herein.

Guarantee
The Penguin mouse is guaranteed for a period of 24 months from the date of the purchase. This guarantee does not apply to misuse or normal wear and tear.

ANTIMICROBIAL PROTECTION

BioCote® – the antimicrobial brand you can trust.
Based on silver ions BioCote® is proven to offer antimicrobial protection for the expected lifetime of the product.
BioCote® keeps your Penguin Ambidextrous Vertical Mouse fresher and cleaner for longer, protecting against odour causing and staining microbes, such as bacteria and mould.
BioCote® has been proven to reduce bacteria/microbes on products by up to 99.5% in two hours OR 99.99% in 24hrs.
BioCote® tested in a laboratory, proven in real life, antimicrobial quality guaranteed.
BioCote® protected products are quality control checked to the appropriate test standard.

Please Note
BioCote® technology does not protect users or others against disease causing bacteria, germs, viruses or other harmful organisms. This technology is not a substitute for good hygiene and/or cleaning practises.