SuperE Q2 PRO Hybrid Active Noise Cancelling Earbuds User Guide
- June 4, 2024
- SuperE
Table of Contents
SuperE Q2 PRO Hybrid Active Noise Cancelling Earbuds
PRODUCT PARAMETERS
| Model name | SuperEQ Q2 Pro |
|---|---|
| Bluetooth version | 5.2 |
| Bluetooth range | 10m/33ft |
| Input | 5V |
| Over-voltage protection | YES |
| Speaker | 12mm Dynamic |
| Noise reduction | (FF+FB) x 2 |
| Acoustic code | SBC, AAC |
| Power display | IOS |
| Battery capacity | 55mAh x 2 (earbuds), 370mAh (charging case) |
Playtime
(varies by volume level and content)
| 70% volume, ANC OFF: Up to 11 hours
(Total 40 hours with the charging case)
70% volume, ANC ON: Up to 8 hours (Total 30 hours with the charging case)
PRODUCT DESCRIPTION
- Indicator light
- Type-C charging port
- Microphone
- Microphone
CHARGING
Fully charge both the earbuds and the charging case before the first use. The
3 LED indicators are lit when fully charged.
Note: Please remove the insulating film on the earbuds when using it for
the first time, otherwise it will not be able to
charge.
WEARING[
](https://manuals.plus
/wp-content/uploads/2022/09/SuperE-Q2-PRO-Hybrid-Active-Noise-Cancelling-
Earbuds-fig-3.png)
- Choose the ear tips that fit your ears best
- Install the ear tips on the earbuds
- Install the ear tips
- Insert the earbuds into the inner canal of your ears and turn gently until you find the most comfortable and secure position
LED DISPLAY[](https://manuals.plus/wp-content/uploads/2022/09/SuperE-Q2
-PRO-Hybrid-Active-Noise-Cancelling-Earbuds-fig-5.png)
- The two earbuds have been paired with each other (normal): the main earbud flashes alternately blue and white and the second earbud flashes white every 5 seconds.
- The two earbuds lose their pairing: The two earbuds flash alternately blue and white.
POWERING ON/OFF
- Open the charging case, the earbuds will automatically power on.
- To power off, place the earbuds in the charging case and close it.
BLUETOOTH PAIRING
First pairing
Open the charging case Turn on the Bluetooth of device 1 Select “SuperEQ Q2 Pro” on your device’s Bluetooth list to connect
Select “SuperEQ Q2 Pro” on your device’s Bluetooth list to connect Turn on the Bluetooth of device 2 Disconnect the Bluetooth connection with the previous device.
CONTROLS[
](https://manuals.plus
/wp-content/uploads/2022/09/SuperE-Q2-PRO-Hybrid-Active-Noise-Cancelling-
Earbuds-fig-11.png)
- Normal/Transparency/ANC ON Long Press(L/R)
- Voice assistant Press 3 times(L/R)
- Play / Pause Press once (L/R)
- Previous track Press twice (L)
- Next track Press twice (R)
- Answer a call Press once (L/R)
- End a call Press once (L/R)
- Reject a call Long Press(L/R)
Normal Mode
It’s the normal mode when you turn on the earbuds at the first time, and it
will turn off if you do not connect it to any Bluetooth device in 3 minutes.
ANC Mode
Reduce the low-frequency ambient noises, press and hold(L/R) to start the ANC
mode.
Transparency Mode
Chat with people without taking off your earbuds, and press and hold (L/R) to
start the Transparency mode.
Voice Assistant
Press 3 times(L/R)to Activate Siri or other voice assistant software.
IMPORTANT[
](https://manuals.plus
/wp-content/uploads/2022/09/SuperE-Q2-PRO-Hybrid-Active-Noise-Cancelling-
Earbuds-fig-14.png)
- Please try to reset the SuperEQ Q2 Pro and restore the factory default if you face any difficulties:
- Place both the 2 earbuds into the charging case. Quickly tap 5 times in both ears at the same frequency. The blue LED flashes and resets successfully.
- If the right and left earbuds disconnect from each other： Please click the left earbud three times to send the pairing instruction to the right earbud, and the pairing will be successful again.