GODEER WF286791 White Twin L-Shaped Bunk Bed Instruction Manual

GODEER WF286791 White Twin L-Shaped Bunk Bed

SAFETY WARNINGS

1. This bed is designed for use only mattress(es) meeting the following specifications on the upper bunk, and lower bunk:
   • Bed type
   • Twin Standard
   • Length
   • 74″ – 75″
   • Width
   • 38 1/2″
   • Thickness
   • 6″
2. Replacement parts, including additional guardrails, may be obtained from any of our ( GIGACLOUD TECHNOLOGY (USA) INC. 18961 ARENTH A VENUS CITY OF INDUSTRY, CA, 91748) dealers
3. Follow the information on the warnings appearing on the upper bunk bed end structure and on the carton. Do not remove the warning label from the bed.
4. Always use the recommended size mattresses or mattress supports, or both, to help prevent the likelihood o entrapment or falls.
5. The surface of the mattress must be at least 5 in. (127 mm) below the upper edge of the guardrails.
6. Do not allow children under 6 years of age to use the upper bunk.
7. Periodically check and ensure that the guardrail, ladder, and other components are in their proper position free from damage and that all connectors are tight.
8. Do not allow horseplay on or under the bed and prohibit jumping on the bed
9. Always use the ladder for entering and leaving the upper bunk.
10. Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
11. The use of a night light may provide added safety precautions for a child using the upper bunk.
12. Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next to the wall, the guardrail that runs the full length of the bed should be placed against the wall to prevent entrapment between the bed and the wall.
13. The use of water or sleep flotation mattresses is prohibited.
14. STRANGULATION HAZARD-Never attaches or hangs items to any part of the bunk bed that are not designed for use with the bed; for example, but not limited, to hooks, belts, and jump ropes.
15. Keep these instructions for future reference
16. Prohibit more than one person on the upper bunk.
17. We recommend assembling your bunk bed on the shipping carton to protect your floor or carpet.
18. Be certain all staples are out of the box before beginning assembly on the shipping carton.

Detail View

Part List

WF286791

WF286792

WF286793

Hardware List

ASSEMBLY TOOLS REQUIRED ( NOT INCLUDED)

PLEASE BE CAREFUL NOT TO DAMAGE THE HOLE POSITION WHEN YOU USE POWER TOOLS.

INSTALLATION SETUP

STEP 1:
Following the below illustration is Assembly FRAME #1 (x2). Using hardware #5 & #1 connect A and B 1 legs with D Frame to complete FRAME #1 (x2).

NOTE: In this step, DO NOT tighten any bolt until you connect all parts together

STEP 2:
Following the below illustration is Assembly FRAME #2. Using hardware #5 & #1 connect A and C legs with D Frame to complete FRAME #2

STEP 3:
Following the below illustration Assembly LEFT BUNKBED. Using hardware #3, #8 & #1 connect FRAME#1 and FRAME#3 with PART J (x2), Fx l(x2), E(x2).

STEP 4:
Below illustration of Assembly STAIRCASE. Using hardware #6 & #1 connect Part M and N with Part to complete STAIRCASE.

STEP 5:
Following the below illustration Assembly STAIRCASE with SIDERAIL G (x2). Using hardware #6 fix Siderail G(x2) to STAIRCASE (Completed on Step 4 ).

STEP 6:
Following the below illustration Assembly LEFT BUNK BED Completed on Step 3) with RIGHT BUNK BED).

• Using hardware #8, #1 & #3 to connect Guardrail L(x2) & K (x2) Side Rail H(x2), STAIRCASE GROUP (Completed on Step 5) with FRAME#1 (Completed on Step 1).
• Using hardware #8, #1, #3 & #4 to connect COMPLETED GROUP (on above step) with LEFT BUNK BED.

STEP 7:
Following the illustration below Assemble THE BED. Use hardware #7 to footer M to connect crossbar J. Use hardware #7 to connect Z bar to crossbar J and F. Use Hardware # 7 to be Z connection with Crossbar L and M.

STEP 8:
Following below illustration is Assembly DRAWER. Connect part R (x3) with part Q and part P by using hardware #2. Use hardware #10 to fix all parts together .

STEP 10:
Following below illustration is Assembly DRAWER. Lay down parts U & V on the Drawer Frame (Completed on Step 10) Then lay down part V (x2) following “Divider” on the Front and Back panels of the Drawer.

STEP 11:
Following below illustration is Assembly DRAWER. Use Screw #9 to screw Hardware #11 to the bottom of Panel S Then use Screw #10 to connect part S with Drawer Frame (completed on Step 9).

STEP 12:
Following the below illustration COMPLETED BED.

Use Screw #1 0(x80) to screw ALL Slat 15 on all the beds Then Push the DRAWER into the under of the RIGHT BUNK BED.

COMPLETED

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>