Aquasabi AQI Series Lamps Instructions
- June 13, 2024
- Aquasabi
Table of Contents
Aquasabi AQI Series Lamps
Product Information
- Model: AQI-40 INTENSE, AQI-60 INTENSE, AQI-80 INTENSE
- Dimensions: 36×10 cm, 57×12 cm, 78×15 cm
- Power Rating: 24 W, 48 W, 72 W
- Luminous Flux: 1800 lm, 3600 lm, 5400 lm
- Color Temperature: 5000-15000 K (adjustable)
- Voltage Rating: 12 V DC
- Current Rating: 2 A, 4 A, 6 A
- Cable Length: 1.5 m
- Holder Height: AQI-40 – 8 cm, AQI-60 – 12 cm, AQI-80 – 12 cm
- Holder Range: AQI-40 – 36-45 cm, AQI-60 – 60-70 cm, AQI-80 – 80-90 cm
Product Usage Instructions
- Clean the PMMA glass cover of the LED module using a soft cloth. Make sure the lamp is turned off before cleaning.
- Before connecting the power supply mains plug to the timer, ensure all cables are connected as shown in the figure.
- If you want to dim the lamp, connect the dimmer in position, and.
- Make sure to use compatible power adapters. For AQI-40, use ESPE-3612. For AQI-60, use ESPE-6012. For AQI-80, use ESPE-9012. Alternatively, you can use other power adapters with identical parameters.
- Compatible dimmers for the product are AQCT-1, AQCT-2, and AQCT-3.
- Caution: Using an inappropriate power supply can cause damage to the lamp or power supply itself.
- If the lamp is damaged, do not attempt to repair it. Contact your supplier for lamp service or replacement of LED modules.
- The LED module in this lamp should only be replaced by qualified personnel. Contact your supplier for details on purchasing LED modules.
- Dispose of the product at designated collection points and do not treat it as unsorted municipal waste.
Please refer to the product manual for more detailed information and instructions.
Installation and safety manual
The AQI series lamps are manufactured in different versions suited for different aquarium dimensions. They come either with a set of holders (H version) to be put on aquarium edges or with slings (S version) to be hanged over the aquarium. Electric ratings of different versions are presented in Table 1.
Model| AQI-40
INTENSE
| AQI-60
INTENSE
| AQI-80
INTENSE
---|---|---|---
Dimensions| 36×10 cm| 57×12 cm| 78×15 cm
Power rating| 24 W| 48 W| 72 W
Luminous flux| 1800 lm| 3600 lm| 5400 lm
Colour temperature| 5000-15000 K adjusted
Voltage rating| 12 V DC
Current rating| 2 A| 4 A| 6 A
Cable length| 1,5 m
Table 1. AQI INTENSE – specification.
SAFETY INSTRUCTIONS
- The product is only intended to be used for aquarium lighting, indoors and at room temperature.
- Follow the installation instructions.
- Keep children and pets other than your aquarium animals away from the lamp.
- Do not use a mechanically damaged device, do not modify the construction.
- Do not switch on the device if any cable(including the power supply)is damaged.
- Only intended to be used with one of the dedicated power supplies*).
- Do not exceed electrical ratings!
- Do not look directly into the light source.
- Turn the lamp on only after it is installed over the aquarium.
- Do not cover the lamp with rugs or blankets.
INSTALLATION INSTRUCTIONS
- H-VERSION The holders are installed with screws and an Allen key (Fig. ❶), which is included with the product delivered.
- The placement of the mounting holes with thread in the lamp housing is shown in Fig. ❷.
- The AQI lamp with holders installed should be on the edges of the aquarium are placed as shown in Fig. ❶.
- The range of holders can be adjusted – details in Table 2.
| AQI-40 | AQI-60 | AQI-80 | |
|---|---|---|---|
| Holder height | 8 cm | 12 cm | 12 cm |
| Holder range | 36-45 cm | 60-70 cm | 80-90 cm |
ASSEMBLY INSTRUCTIONS – S VERSION
- Ropes for hanging the lamp are supplied with the installation manual. follow the instructions in the manual for rope installation. The The lamp housing has 4 holes for the mounting kit are confirmed.
- It is recommended to use hoods when using the hanging version of the lamp used. Remove the protective film of the hoods. The hoods have 4 mounting holes, as shown in Fig ❸.
- To install the shades on the lamp you will need to remove the acrylic base and… install sliders in the position shown in figure ❹. Around the To install lampshades, loosen the screws in the lamp base (do not loosen) and slide the slide outward.
- Then place the lampshade between the LED housing and the slider and push this inward, so that the lampshade passes through the holes in the slider is blocked. Tighten the screws.
GENERAL INSTRUCTIONS AND HANDLING
- The PMMA glass cover of the LED module should be cleaned using a soft cloth. Do not clean the lamp when it is turned on.
- All cables should be connected as shown in Fig. ❺ before the power supply mains plug is connected to the timer. The dimmer should be connected in position ①, ②, and ③ if the lamps are to be dimmed down*).
- List of compatible power adapters:
| AQI-40 | ESPE-3612 |
|---|---|
| AQI-60 | ESPE-6012 |
| AQI-80 | ESPE-9012 |
or other with identical parameters. **) Compatible dimmer: AQCT-1, AQCT-2, AQCT-3
CAUTION
Using an inappropriate power supply will result in damage to the lamp or power
supply itself!
REPAIRS AND UTILIZATION Do not try to repair a damaged lamp. For information about lamp service contact your supplier. The LED module in this lamp is not intended to be replaced by unqualified personnel. LED modules are available from your supplier, contact them for details. The product cannot be disposed of as unsorted municipal waste. According to the directive 2012/19/UE, the device should be disposed of at designated collection points.
WARRANTY
SKYLIGHT warrants this product to be free of defects in material and
workmanship under normal use for 2 years from the date of purchase. The
obligation of this warranty is limited to the repair or replacement of
defective elements.
No claim shall be allowed under this warranty if, in the opinion of SKYLIGHT,
this product has been subject to accident or improper usage, including, but
not limited to: damage, improper storage, accidental dropping, etc.
Please send the damaged device to your supplier including the power supply and
cables, the completed warranty card, and the receipt. The serial number on the
device has to be the same as on the warranty card. The obligation of this
warranty is limited to the device bought, and no claim shall be allowed under
this warranty due to damage or loss of any other objects.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>