ICON 54002 22 Up Tundra Billet Lower Link Kit Instruction Manual
- June 13, 2024
- Icon
Table of Contents
ICON 54002 22 Up Tundra Billet Lower Link Kit
COMPONENTS INCLUDED
- (2) 157552 22-UP TUNDRA REAR LOWER LINK
- (2) 157546 22-UP TUNDRA SERRATED SPACER .259
- (2) 157548 22-UP TUNDRA SERRATED SLEEVE .259
- (2) 157420 NUT PLATE 3/8-16 X 2
- (4) 157551 HEIM SPACER 1.00 X .559 X 2.834
- (2) 167014 L/R ADJUSTER SLEEVE 1.25-12L / 1.00-14
- (2) 127205 16.6” TRAILING ARM WEAR STRIP
- (2) 295510 JM16-1T 1-14 RH ROD END F2 FIT
- (2) 297102 GREASELESS PRESS IN BUSHING
- 2.135 X 14.3 X 58.85MM
HARDWARE INCLUDED
- (14) 605018 10-32 X .438 FLAT HEAD SCREW STAINLESS
- (4) 605146 3/8-16 X 1.5 12 PT FLANGED CAP SCREW
TOOLS REQUIRED
- JACK
- JACK STANDS
- TORQUE WRENCH
- 19MM SOCKET / WRENCH
- 3/8 12-PT SOCKET / WRENCH
TECH NOTES
- DO NOT EXCEED 3.375” ADJUSTMENT FROM THE CENTER OF THE ROD END TO THE EDGE OF THE
- BILLET LINK. FAILURE CAUSED BY EXCESSIVE ADJUSTMENT WILL NOT BE COVERED UNDER ICON’S WARRANTY POLICY.
- LINKS ARE PRESET TO 26.938” (FACTORY LENGTH).
- IF A CUSTOM PINION ANGLE IS DESIRED YOU CAN ADJUST THIS WITH THE VEHICLE ON THE GROUND.
WARNING!
- READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH
- BEFORE BEGINNING INSTALLATION! IF THESE INSTRUCTIONS ARE NOT PROPERLY FOLLOWED SEVERE FRAME, SUSPENSION AND TIRE DAMAGE MAY RESULT TO THE VEHICLE!
- ICON VEHICLE DYNAMICS RECOMMENDS THAT YOU EXERCISE
- EXTREME CAUTION WHEN WORKING UNDER A VEHICLE THAT IS SUPPORTED WITH JACK STANDS.
- ICON VEHICLE DYNAMICS RECOMMENDS ALL INSTALLATION TO
- BE PERFORMED BY A PROFESSIONAL SHOP/SERVICE TECHNICIAN.
- PRODUCT FAILURE CAUSED BY IMPROPER INSTALLATION WILL NOT BE COVERED UNDER ICON’S WARRANTY POLICY
INSTALLATION
- Lift vehicle and securely place heavy-duty jack stands under the manufacturer-recommended lifting locations for the back of the vehicle. NEVER WORK UNDER AN UNSUPPORTED VEHICLE.
- Remove the wheels.
- Remove the driver-side rear upper link using a 19mm. [FIGURE 1]
- Install the billet link with the heim joint toward the frame and the pinch bolts up. The pinch bolts should be on the outer side of the link. Tighten the factory hardware to factory spec using a 19mm. [FIGURE 2]
- Repeat the steps on the opposite side of the vehicle.
- To adjust, loosen the pinch bolt’s billet link using a 3/8” 12pt. Turn the L/R adjusting collar until the desired length is reached.
- Make sure that the slit in the collar is lined up with the slit in the pinch housing and tighten pinch bolts using an alternating pattern [Torque to 40 ft-lbs]. Go back and forth between bolts 3 times to torque equally.
- Never exceed the maximum length as listed in the tech notes
VERIFY ALL FASTENERS ARE PROPERLY TORQUED BEFORE DRIVING THE VEHICLE TORQUE ALL NUTS, BOLTS AND LUGS AFTER 100 MILES AND PERIODICALLY THEREAFTER
ICON VEHICLE DYNAMICS LIMITED LIFETIME WARRANTY
ICON Vehicle Dynamics warrants to the original retail purchaser who owns the vehicle on which the product was originally installed. ICON Vehicle Dynamics does not warrant the product for finish, alterations, modifications and/or installation contrary to ICON Vehicle Dynamics instructions. ICON Vehicle Dynamics products are not designed, nor are they intended to be installed on vehicles used in race applications, for racing purposes or for similar activities. (A “race” is defined as any contest between two or more vehicles, or a contest of one or more vehicles against the clock, whether or not such contest is for a prize). This warranty does not include coverage for police or taxi vehicles, race vehicles, or vehicles used for government or commercial purposes. Also excluded from this warranty are sales outside of the United States of America and Canada.
ICON Vehicle Dynamics’ obligation under this warranty is limited to the repair or replacement, at ICON Vehicle Dynamics’ discretion, of the defective product. Any and all costs of removal, installation or re-installation, freight charges and incidental or consequential damages are expressly excluded from this warranty. Items that are subject to wear are not considered defective when worn and are not covered. ICON Vehicle Dynamics components must be installed as a complete kit as shown in our current application guide. Any substitutions or exemptions of required components will immediately void the warranty. Some finish damage may happen to parts during shipping and is not covered under warranty. This warranty is expressly in lieu of all other warranties expressed or implied. This warranty shall not apply to any product that has been improperly installed, modified or customized subject to accident, negligence, abuse or misuse
7929 Lincoln Ave. Riverside, CA 92504 Phone: 951.689.ICON Fax: 951.689.1016 www.iconvehicledynamics.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>