Overade 2AUZS-OXLM Oxi Turn Bike Lighting With Turn Signal Indicators Owner’s Manual

**Overade 2AUZS-OXLM Oxi Turn Bike Lighting With Turn Signal Indicators Owner’s Manual

**

INSTRUCTION

We invite you to register your product on our website. This will permit you to receive our latest deals and activate your product warranty more easily if needed.
How to register your product?

1. Go on www.overade.com/oxi-warranty
2. Fill in the online form
3. You’ll then receive a confirmation email including a welcome offer

HOW TO ATTACH THE DEVICE?

The OxiTurm light can be attached to the majority of urban helmets using the magnetic mount (supplied in the box), and to any other support (sports helmets, bicycles, scooters) using the kit of additional fasteners available on our website (not included).

Attaching the magnetic mount: before attaching the magnetic mount by removing the protective film from the adhesive, make sure to clean the helmet’s attachment surface with lukewarm water only. Do not use any solvents.

WARNING! Make sure that the magnetic mount is correctly positioned on the helmet as it cannot be removed, so that the lighting is in the right (see figure 1).

The OxiTurn light can then be attached to the mount (s ee figure 2 ) and removed at will.

FIRST USE.

Before first use, fully charge the battery using the cable provided and connected to a 5V USB charger (see figure 3)

A flashing red light indicates that the light is charging. The flashing light will turn orange, if the light is at more than 50% capacity. When the light turns off, the battery is fully charged. Elastic straps are provided for mounting the OxiMote remote control on a handlebar **(see figure 4).

**

Choose the most suitable length. You can use one or two elastic bands, depending on the shape of the handlebars. The remote control works with a CR2032 battery already in place. The battery can be changed by removing the 3 screws with a screwdriver **(see figure 5).

**

FUNCTIONNING.

To turn on the OxiTurn light, press the ON/OFF button located in the centre of the front panel. To turn it off, press the button for 2 seconds. To switch from one light mode to another, simply press the ON/OFF button. The power and operating times for each mode are shown figure 6.

In Day Mode 6, the lighting only comes on when it is activated by the Oximeter (turn signal) or by the Oxirane (brake warning).

After switching your light on or off, the charge indicator turns green for a few seconds or red when the battery level is low.

TURN SIGNALS.

The direction indicators are activated by the OxiMote remote control. When a turn signal is activated, an audible
reminder confirms that it is working, as well as an illuminated reminder on the OxiMote. To change the sound, press
the ON/OFF button for at least 6 seconds when the OxiTurn light is off. A sound signal indicates that the change has
been made. To deactivate the sound, repeat the operation a second time.
WARNING! The use of flashing lights may be regulated in some countries. Observe the applicable law.

PAIRING OXITURN LIGHT WITH OXIMOTE

WARNING! This product is a supplementary light, it cannot replace the vehicle lighting defined by the Highway Code. Do not immerse the product in water and do not dismantle the light, as this will invalidate the warranty. Do not dispose of the battery in fire (risk of explosion).

WARNING! This product and batteries it contains cannot be disposed of with household waste. They are subject to selective sorting and must be deposited in an authorized collection area for recycling.

CONNECTING OXI PRODUCTS TO EACH OTHER

The products of the Ox range can be connected together 2 by 2 using the pairing procedure [A] described below.

WARNING! The OxiTurn and Oximeter in the package are already connected to each other. It is therefore not necessary to use the pairing procedure. Use this procedure if you want to connect an additional Oxi product or if you have deleted the pairings of an Oxi product.

PAIRING OXITURN LIGHT WITH OXIMOTE

1. On OxiTurn light, switch on the light by pressing and releasing the button
2. Press and hold the button (at least 6s) until the button flashes **orange.

If the pairing is successful : – the light button lights up continuously in orange for a few seconds and then turns off

**

On OxiMote, press and hold the 2 buttons(at least 4s) until they flash orange

Oxi Mote buttons light up continuously in orange for a few seconds and then turns off => **Other cases***

Repeat the pairing process if not successful.

If the button on the OxiTurn lights up alternately in red and green, or if the Oximeter lights up in orange and red after pairing instead of continuously, this means that it cannot be paired with additional products. Delete all pairings to be able to pair a new one (see [C])

MULTI-PAIRING

To connect an additional Oxirane or Oximeter to your OxiTurn lighting, repeat the procedure [A].

To connect an additional OxiTurn light to your Oximeter, repeat the procedure [A].

DELETING ALL PAIRINGS ON OXITURN LIGHT

1. Switch on OxiTurn by pressing the button
2. Press and hold the button (at least 6s) until the button flashes orange (pairing mode)
3. Press the button 3 times quickly (within 4s)

If pairings are correctly deleted:  the button flashes rapidly in green

DELETING ALL PAIRINGS ON OXIMOT

1. Press and hold the 2 buttons(at least 4s) until they flash orange (pairing mode)
2. Quickly press the left button twice and the right button twice (within 4s)

If pairings are correctly deleted:  buttons are flashing in orange and red

WARRANTY.
We apply the legal warranty periods on all our products. For more information on terms and conditions, please contact your local dealer or visit our website at www.overade.com

INSTRUCTION

Oxi Compliant wireless connectivity

www.overade.com/oxi

**Discover our range

**

To switch your light to a Brake Light

Red and White Light

Additional fasteners

Sold separately – Check them out on our website

Model: OXLM

OVERADE S.A.S – 13 rue Georges Auric – 75019 PARIS – FRANCE
www.overade.com

FCC STATEMENT:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

References

• Casque pliable & Sacoche sécurisée
• Oxi fait communiquer simplement vos éclairages
• FRM-OXI-GARANTIE
• FRM-OXI-GARANTIE
• Casque pliable & Sacoche sécurisée

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>