Soundsphere SS-Q-8 Surround Sound, Woofer Owner’s Manual

June 13, 2024
SOUNDSPHERE

Soundsphere SS-Q-8 Surround Sound Woofer

Soundsphere-SS-Q-8-Surround-Sound-Woofer-product

Please read the following instructions carefully before installing your Soundsphere® speaker. If you have any questions regarding installation that are not answered in the following directions, please contact your local sound contractor or the Soundsphere®/MSE Audio® technical support team.

General Information

  • Maximum Amplifier Power: 100 Watts RMS
  • Nominal Impendance: 8 ohms

Wiring

Amplifier connection is via flying leads. Connect the positive (+) amplifier lead to the RED input wire. Connect the negative (-) amplifier lead to the BLACK wire. Secure connections us-ing wire nuts, etc. For wiring optional 100W transformer, see section “TX-100 Transformer Installation Instructions” on page 2 of this manual.

Mounting

Hanging Kit

Mount using one of the following methods:

  • Properly secured wire rope with a minimum breaking strength of 225 lbs. (for a 10:1 safety factor).
  • Beam clamp with proper load rating.

It is recommended to use a secondary wire rope support around one of the Q-8 legs. Do not use rope for mounting. The use of chain is not recommended unless rated for suspension of loads greater than or equal to 225 lbs (for a 10:1 safety factor).

Surface Mount Bracket

Secure the bracket to the hard surface using proper hardware. Secure the Q-8 to the bracket using the washers and nylon locknuts provided. It is recommended to use a secondary wire rope support around one of the Q-8 legs and through an unused bracket hole.

Warranty

Soundsphere loudspeakers carry a 5 year limited warranty and a 3 year limited warranty on all electrical components. See war-ranty sheet for details and limitations.

Replacement Parts

  • 8” 100 Watt coaxial loudspeaker driver with crossover.
    • Order Model Number CX-8

Always check local requirements for overhead suspension of loudspeakers.

Replacing the Coax Driver and Crossover in the Q-8

  1. Remove the reflector from the Q-8 by removing the 3 bolts, washers, and tabs.
  2. Remove the 4 screws securing the driver. Remove the driver by gently lifting the tweeter with one hand and removing it with the other hand. Pull the wire out through the hole in the bolt.
  3. Feed the wire from the replacement driver through the drilled bolt inside the sphere. Install the new driver and secure with screws.

Other Information

Wire runs between the amplifier(s) and loudspeaker(s) must be of the appropriate gauge to insure the full audio performance capabilities of the Soundsphere loudspeakers. This applies to all loudspeaker impedances (4 or 8 Ohms) or audio line voltages (50, 70.7 or 100 Volts). For more information, please see the ‘Downloads” section at www.soundsphere.com, or call our Customer Service at 913.663.5600.

TX-100 Transformer Installation Instructions

The TX-100 is designed for use with the Model Q-8 loudspeaker. Power taps are provided for 25V, 70V, and 100V systems:

| 25V| 70V| 100V
---|---|---|---
Green| Common| Common| Common
Brown| 25W| –| –
Purple| 12.5W| 100W| –
Orange| –| 50W| 100W
Yellow| –| 25W| 50W
White| –| 12.5W| 25W
Blue| –| –| 12.5W

Soundsphere-SS-Q-8-Surround-Sound-Woofer \(2\)

Remember to clip and insulate unused input wires; shorting any input wire to another will reduce the volume level and place an unexpected load on the power amplifier.

  • Notes:
    • Red or Red with a White stripe is an 8-ohm tap.
    • The total tap wattages should not exceed the amplifier’s capability.
  • WARNING
    • Be sure to securely tighten all hardware before hanging the loudspeaker. Wire rope (steel cable), cable clamps with saddles, and thimbles of suitable size and strength are the recommended materials for overhead suspensions. All loudspeakers should be redundantly safety-wired to structural members of the building with an approved safety wire system or other agency-certified materials.
  • IMPORTANT
    • Always check local safety codes before installing any overhead loudspeaker system and for periodic inspection and maintenance of the installation.

Contact Information:

Copyright Notice:

  • © 2021 MSE Audio
  • Revision Date: 02.25.2021

Slogan:

  • 360º of the Best Sound Around™

FAQs

How much power can the Soundsphere SS-Q-8 handle?

The Soundsphere SS-Q-8 can handle a maximum amplifier power of 100 Watts RMS.

What is the nominal impedance of the SS-Q-8?

The nominal impedance of the SS-Q-8 is 8 ohms.

How should I wire the SS-Q-8 to my amplifier?

The amplifier connection is made via flying leads. Connect the positive (+) amplifier lead to the RED input wire and the negative (-) amplifier lead to the BLACK wire. Ensure secure connections using wire nuts or equivalent. For wiring an optional 100W transformer, refer to the TX-100 Transformer Installation Instructions on page 2 of the manual.

What is the warranty coverage for Soundsphere loudspeakers?

Soundsphere loudspeakers come with a 5-year limited warranty and a 3-year limited warranty on all electrical components. Please refer to the warranty sheet for detailed terms and limitations.

How should I install the TX-100 Transformer for use with the SS-Q-8?

The TX-100 Transformer is designed for use with the Model Q-8 loudspeaker and provides power taps for 25V, 70V, and 100V systems. Refer to the provided color coding for connections and be sure to clip and insulate unused input wires. Make sure not to exceed the amplifier's capability when selecting tap wattages.

What safety precautions should I take when installing overhead loudspeakers?

Before hanging the loudspeaker, ensure that all hardware is securely tightened. Use recommended materials like wire rope (steel cable), cable clamps with saddles, and thimbles for overhead suspensions. All loudspeakers should be redundantly safety-wired to structural members of the building using approved safety wire systems or agency-certified materials. Always check local safety codes before installation.

Can the SS-Q-8 be used outdoors or in marine environments?

No, the SS-Q-8 is not designed for outdoor or marine use. It is recommended for indoor installations. Exposing it to moisture or extreme outdoor conditions can damage the speaker.

How can I obtain replacement parts for the SS-Q-8?

Replacement parts, such as the 8 inches 100 Watt coaxial loudspeaker driver with crossover, can be ordered using Model Number CX-8. Contact your authorized dealer or Soundsphere for ordering details.

Can I paint or customize the appearance of the SS-Q-8?

It is recommended not to paint or customize the appearance of the SS-Q-8 unless you consult Soundsphere/MSE Audio for guidance. Altering the speaker's exterior may affect its performance and warranty.

Does the SS-Q-8 require periodic maintenance?

The SS-Q-8 does not require regular maintenance. However, it's essential to perform occasional visual inspections to ensure no physical damage has occurred during use.

Are there any specific installation guidelines for suspended mounting of the SS-Q-8?

When suspending the SS-Q-8, always adhere to local safety codes and guidelines for overhead loudspeaker installations. Ensure that wire rope and hardware are rated for the speaker's weight and securely fastened to structural members.

Can I connect the SS-Q-8 to a 70.7V audio line voltage system?

Yes, you can connect the SS-Q-8 to a 70.7V audio line voltage system. Ensure that you follow the recommended color-coded connections and tap wattages as described in the TX-100 Transformer Installation Instructions.

How do I properly insulate unused input wires on the TX-100 Transformer?

To prevent shorting of input wires, make sure to clip and insulate any unused input wires on the TX-100 Transformer. Proper insulation helps maintain audio performance and protects the power amplifier.

Download This PDF Link: Soundsphere SS-Q-8 Surround Sound, Woofer Owner’s Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals