IKEA SBE8596Z1I_9001781932 KALLBODA Integrated Dishwasher Instruction Manual
- June 13, 2024
- Ikea
Table of Contents
KALLBODA
SBE8596Z1I_9001781932
Integrated Dishwasher
Instruction Manual
SBE8596Z1I_9001781932 KALLBODA Integrated Dishwasher
www.ikea.com|
---|---
| 
| 
Product information
→ Fig. 1
Product description
Appliance
You can find an overview of the parts of your appliance here.
→ Fig. 2
1| Rating plate| Rating plate with E number and FD number. The data you need
for Customer Service.
---|---|---
2| Detergent dispenser| Add detergent to the detergent dispenser.
3| Bottom basket| Bottom basket
4| Dispenser for special salt| Add special salt to the dispenser for special
salt.
5| Lower spray arm| The lower spray arm washes the tableware in the bottom
basket. If the tableware has not been washed properly, clean the spray arms.
6| Tablet collecting tray| During the wash cycle tablets automatically fall
out of the deter- gent dispenser into the tablet collecting tray where they
can fully dissolve.
7| Top basket| Top basket
8| Cutlery drawer| Cutlery drawer
9| Emotion Light| Interior lighting of the appliance.
10| Cutlery shelf| Cutlery shelf
11| Upper spray arm| The upper spray arm washes the tableware in the top
basket. If the tableware has not been washed properly, clean the spray arms.
12| Intake opening| The intake opening is required for the Drying.
13| Blow opening| The blow opening is required for the Drying.
14| Filter system| Filter system
15| Dispenser for rinse aid| Add rinse aid to the dispenser for rinse aid.
Features
You can find an overview of the possible features of your appliance and how to
use them here.
These features depend on the model of your appliance.
Adjusting top basket with side levers
To wash large items of tableware in the baskets, adjust the shelf position of
the top basket.
→ Fig. 3 – 4
Reorganising cutlery drawer
You can fold down the side shelves and front prongs to make more space for
longer/wider items of cutlery.
→ Fig. 5 – 6
Folding down prongs
If you do not need the folding tines, fold them down.
→ Fig. 7
Before first use
Performing the initial configuration
On initial start-up or after a reset to the factory settings, you will need to
make settings.
Requirement: The appliance has been installed and connected.
- Add special salt.
- Add rinse aid.
- Switch on the appliance.
- Setting the water softening system.
- Set the amount of rinse aid to be dispensed.
- Add detergent.
- Start the Programme with the highest cleaning temperature without tableware.
We recommend you clean the appliance without tableware before using it for the first time to remove any marks from water or other residues.
Tip: You can change these settings and other Basic settings at any time.
Adding special salt
If the special salt refill indicator lights up, add special salt to the
dispenser for special salt just before the programme starts.
ATTENTION!
- Detergent may damage the water softening system.
- Only fill the dispenser of the water softening system with special dishwasher salt.
- Special salt can damage the tub due to corrosion.
- To make sure that any special salt that escapes is washed out of the tub, add the special salt to the dispenser for special salt immediately before the programme starts.
→ Fig. 8 – 13
Adding rinse aid
If the rinse aid refill indicator lights up, top up with rinse aid.
Only use rinse aid for domestic dishwashers.
→ Fig. 14 – 17
Setting water softening system
Set the water hardness on your appliance.
→ Fig. 18
Overview of water hardness settings
You can find an overview of the water hardness values that can be selected
here.
| WATER HARDNESS °E | HARDNESS RANGE | MMOL/L | SETTING VALUE |
|---|---|---|---|
| 0 – 8 | Soft | 0 – 1.1 | H00 |
| 9 – 10 | Soft | 1.2 – 1.4 | H01 |
| 11 – 12 | Medium | 1.5 – 1.8 | H02 |
| 13 – 15 | Medium | 1.9 – 2.1 | H03 |
| 16 – 20 | Medium | 2.2 – 2.9 | H04 |
| 21 – 26 | Hard | 3.0 – 3.7 | H05 |
| 27 – 38 | Hard | 3.8 – 5.4 | H06 |
| 39 – 62 | Hard | 5.5 – 8.9 | H07 |
Regeneration of the water softening system –overview
In order to ensure fault-free operation of the water softening system, the
water softening system is regenerated in all programmes before the end of the
main rinse cycle.
Here, you can find an overview of the maximum additional running time and
consumption values during regeneration of the water softening system. You can
find the column applicable to your product variant according to its water
consumption in the Eco 50° programme.
| Regeneration of the water softening system after x washing programmes | 6 |
|---|---|
| Additional running time in minutes | 7 |
| Additional water consumption in litres | 5 |
| Additional power consumption in kWh | 0.05 |
The consumption values specified are laboratory measurements determined in
accordance with the currently applicable standard using the Eco 50° programme
and with the factory value of the water hardness set to 16 – 20°E .
Setting the amount of rinse aid
If there are streaks or water marks on tableware, change the amount of rinse
aid.
Note: A low level adds less rinse aid during the wash cycle, a higher setting
adds more rinse aid during the wash cycle. → Fig. 19
Detergent
Only use detergents that are suitable for dishwashers. Both separate and
combined detergents are suitable.
For optimum washing and drying results, use separate detergent, adding special
salt and rinse aid separately.
Note: Follow the manufacturer’s instructions for each detergent.
If you are using tablets, one is enough. Insert the tablets in a horizontal
position.
If you are using powder or liquid detergent, follow the manufacturer’s
instructions and quantities for dosage in the detergent dispenser.
20 ml – 25 ml detergent is sufficient for normal soiling.
If tableware is only lightly soiled, slightly less than the amount of
detergent specified is usually sufficient.
Control panel
You can use the control panel to configure all functions of your appliance and
to obtain information about the operating status.
→ Fig. 20
1| ON/OFF button **** and reset button| Switching on the appliance Switching
off the appliance Terminating the programme
---|---|---
2| Programme buttons| Programmes
3| Display| The display shows information about the remaining running time or
the basic settings. You can change the basic settings via the display and the
setting buttons.
4| Timer programming and setting buttons| Setting timer programming Changing
basic settings
5| Programme buttons and additional functions| Programmes Additional functions
6| Start button| Starting the programme
7| Water supply display| Display for water supply
8| Door opener| Opening the appliance door
9| Special salt refill indicator| Water softening system
10| Rinse aid refill indicator| Rinse aid system
11| button| If you press Setup 3 sec. for approx. 3 seconds, you can open the
basic settings.
Overview of programmes
You can find an overview of the programmes that can be set here.
Start a programme:
→ Fig. 21
Set the start time for a programme:
→ Fig. 22
PROGRAMME| 1) PROGRAMME DURATION IN H:MIN
2) ENERGY CONSUMPTION IN KWH
3) WATER CONSUMPTION IN L| PROGRAMME SEQUENCE
---|---|---
Intensive 70°| ● 1) 2:25 – 2:30
● 2) 1.150 – 1.250
● 3) 10.5 – 13.5| Intensive:
● Pre-Rinse
● Cleaning 70 °C
● Intermediate rinse
● Final rinse 50 °C
● Dry
AUTO
Auto 45-65°| ● 1) 1:40 – 2:40
● 2) 0.680 – 1.300
● 3) 7.0 – 15.5| Sensor-controlled:
● Optimised by sensors depending on the soiling level of the washing water
ECO
Eco 50°| ● 1) 3:55
● 2) 0.747
● 3) 9.5| Most economical:
● Pre-rinse
● Clean 50 °C
● Intermediate rinse
● Final rinse 35 °C
● Drying
Quiet 50°| ● 1) 4:00
● 2) 0.800
● 3) 10.5| Reduced noise:
● Pre-Rinse
● Cleaning 50 °C
● Intermediate rinse
● Final rinse 35 °C
● Dry
Glass 40°| ● 1) 1:40 – 1:45
● 2) 0.750 – 0.800
● 3) 11.1 – 13.7| Particularly gentle:
● Pre-Rinse
● Cleaning 40 °C
● Intermediate rinse
● Final rinse 50 °C
● Dry
Quick 65°| ● 1) 1:00
● 2) 1.280
● 3) 10.2| Time-optimised:
● Cleaning 65 °C
● Intermediate rinse
● Final rinse 69 °C
● Dry
Quick 45°| ● 1) 0:35
● 2) 0.710
● 3) 10.5| Time-optimised:
● Cleaning 45 °C
● Intermediate rinse
● Final rinse 50 °C
Pre Rinse| ● 1) 0:15
● 2) 0.050
● 3) 4.0| Cold rinse:
● Pre-rinse
Machine Care| ● 1) 2:10
● 2) 1.350
● 3) 15.0| Use only if appliance is unloaded. Machine Care 70 °C
Information for test institutes
Test institutes are provided with information for comparability tests, e.g.
according to EN60436.
These are the conditions for conducting the tests, however they are not the
results or consumption values.
E-mail enquiries to: dishwasher@test-appliances.com The product number (E-Nr.) and the production number (FD) are
required here. They can be found on the rating plate on the appliance door.
Additional functions
You can find an overview of the additional functions that can be set here.
| ADDITIONAL FUNCTIONS | USE |
|---|---|
| Quick Plus | ● The run time is shortened by 15% to 75% depending on the rinse |
programme.
● Energy and water con- sumption are increased.
Half Load| ● Switch on with small loads.
● It is recommended adding less detergent to the detergent dispenser than for
a full machine load.
● The run time is shortened.
● Energy and water con- sumption are reduced.
ADDITIONAL FUNCTIONS| USE
---|---
Extra Dry| ● For a better drying result the final rinse temperature is
increased and the drying phase extended.
● Especially suitable for dry- ing plastic parts.
● There is a slight increase in energy consumption and the run time is
extended.
Intensive Zone| ● Switch on with mixed loads containing table- ware with
different soil- ing levels, e.g. place very soiled pots and pans in the bottom
basket and normally soiled tableware in the upper basket.
● The spray pressure in the bottom basket is in- creased and the max- imam
programme temperature held longer. This will increase the run time and energy
consumption.
Handling problems
If you have a problem with your appliance, refer to the “Troubleshooting” section in the full version of the user manual, which is available on the following pages: www.ikea.com.
Technical specifications
| Dimensions (HxWxD) | 865 x 598 x 550 mm |
|---|---|
| Weight | Max.: 60 kg |
| Voltage | 220 – 240 V, 50 Hz or 60 Hz |
| Power rating | 2000 – 2400 W |
| Fuse | 10 – 16 A |
| Water pressure | ● Min. 0.05 MPa (0.5 bar) |
● Max. 1 MPa (10 bar)
Inlet rate| Min. 10 l/min
Water temperature| Cold water.
Hot water max.: 60 °C
Capacity| 14 place settings
You can find more information about your model online at
https://eprel.ec.europa.eu/. This web address is linked to the official EU
EPREL product database. Please then follow the instructions on searching for
the models. The model identifier is made up of the model name and article
number without dots. This information can be found on the label on the right
side of the appliance door.
Note: To save energy and water, load the machine with the maximum number
of place settings specified.
Information regarding free and open source software
This product includes software components that are licensed by the copyright
holders as free or open source software. This licence information can be
downloaded via our home page www.ikea.com.
Alternatively, you can request relevant information from
se.hfb70.running.range@inter.ikea.com.
The source code will be made available to you on request. Please send your
request to the above address. Subject: “FOSS”
To download the full document, visit www.ikea.com
23320
© Inter IKEA Systems B.V. 2023
AA-2361282-1