Gprinter CATPR Wireless Thermal Printer User Manual
- June 4, 2024
- Gprinter
Table of Contents
Gprinter CATPR Wireless Thermal Printer User Manual
Fast Installation Guide
Portable Mobile Printer This product is only suitable for safe use in non- tropical climate conditions.
Product View:
The equipment contains model approval codes (respectively):
CMIIT ID 2021DP10891
CMIIT ID 2021DP11268
CMIIT ID 2019DP4046
CMIIT ID 2018DP1893 Different modules are subject to the actual products.
Printer description:
- LED display
- MENU
- Power/Save
- Feed / Set
- Strap hole
- USB port
- Top Cover Open button
Note:
The transmission interface, appearance of the printer in the picture will
vary according to the type of model you purchased. For the actual
transmission interface and appearance please refer to the material object.
Basic Button Function
- Press top cover button to open the media cover.
- Insert the media roll spindle into a media roll and fix it in the center of the paper cavity
- Place the media roll spindle on the media roll mount.
- Pull out 1cm media out of printer and close the cover correctly.
- When printing is complete, tear the label paper from forward.
- Model specifications, accessories, parts and program content are subject to the actual machine, subject to change without notice.
Button Function
Menu Options Description
Users can learn more products and technical information from www.gainscha.net.
⚠ Disclaimer: This product is a Class A product. This product can only be used safely in non-tropical areas. In a living environment, this product may cause radio interference. In this case, the user may be required to take practical measures against interference.
Technical Parameters
Troubleshooting
The following guide lists the most common problems that may be encountered when operating this printer. If the printer still does not function after all suggested solutions have been invoked, please contact the Customer Service Department of your purchased dealer or distributor for assistance.
Warranty clause
Non-warranty clause
Description of the restricted use of hazardous substances in electrical and electronic products
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
ISED Statement
‐ English: This device complies with Industry Canada license‐exempt RSS
standard(s). Operation is subject to the following two conditions: (1) This
device may not cause interference, a
nd (2) This device must accept any interference, including interference that
may cause undesired operation of the device.
The digital apparatus complies with Canadian CAN ICES‐3 (B)/NMB‐3(B).
This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.
RF Exposure Statement
The device has been evaluated to meet general RF exposure requirement. This
equipment should be installed and operated with minimum distance 0mm between
the radiator & your body.