SUTA STCB6 Smart Home User Manual
- June 13, 2024
- SUTA
Table of Contents
SUTA STCB6 Smart Home User Manual
System configuration
Control Box Interface Definition
STCB6-421H-31
Remote control Button
STRM6-2012-A1
| Button label | Function |
|---|---|
| 1 | The back motor extends |
| 2 | The back motor retracts. |
| 3 | The foot motor extends. |
| 4 | The foot motor retracts |
| 5 | The motors reach to ZG position (pre-set) Resetting way: Adjust the back |
and foot motor to the position, long press theZG button for about 10s, once
you hear bleeping sound fromthe buzzer on control box,and the backlight on
remoteflashes,the ZG position is reseted successfully. (Restore the factory
default settings if power off)
6| Press once, all motors retract to the minimumposition.(Will not retract if
power off and on again)
7| The head motor extends.
8| The head motor retracts.
9| The lumbar motor extends.
10| The lumbar motor retracts.
11| Back massage, there are 3 levels in total.
12| Foot massage, there are 3 levels in total.
Bluetooth function description
Step 1| APP
Search for “SUTA” in the APP store and install.
---|---
Step 2| Open APP when installation done, bluetooth and location should be both
on. Hold on the pairing button on the pairing cable for 3 seconds and release.
And pull down the APP to refresh at the same time, and click the model when it
shows “pairing”. It will go to the remote control page, pairing done.
Step 3| After going to the remote controlling page, you can control the device
by APP now.
Attention:
To protect the reliability and safety of the motor and control box, do not
switchthekeys frequently.
Other models:
Control box:
STCB6-221H-31 比 STCB6-421H-31.
STCB6-221H-31 is less ports than STCB6-421H-31，same way to use.
Remote:
STRM6-2008-A1，STRM6-2010-A1 比 STRM6-2012-A1.
STRM6-2010-A1 are less buttons than STRM6-2012-A1，samewayto use.
RF exposure statement
This equipment complies with the FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or noncooperation with any other antenna or transmitter.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to receivership is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>