EATPOW HT-WR818 150Mbps Wireless USB Dongle Installation Guide
- June 13, 2024
- EATPOW
Table of Contents
EATPOW HT-WR818 150Mbps Wireless USB Dongle
Product Information
The 150Mbps Wireless dongle is a device that allows you to connect your computer to a wireless network. It provides a convenient and reliable way to access the internet wirelessly.
System Requirements:
- One available USB 1.1/2.0 port
- Operating System: Windows ME/2000/XP/win7/win8/win10/win11
Product Usage Instructions
- Power on your computer and allow the Windows operating system to load fully.
- Insert the 150Mbps Wireless dongle into an available USB port on your PC.
- Put the CD driver that came with the product into the CD Rom of your PC. You will see the CD driver installation disk appear on the bottom right corner of your PC.
- Click on “My computer” and find the G disk. Double-click on it for automatic driver installation.
- Once the driver installation is complete, you can connect the wireless router to the internet.
Note:
- The screen-shots provided in the manual are based on Windows Vista, but the procedures are the same for other operating systems.
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
System Requirements
- One available USB 1.1/2.0 port
- Operating System: Windows ME/2000/XP /win7/win8/win10/win11
Software Installation
You must have the following information available before installing your product
- Wireless Network Name (SSID) and,
- Encryption/Network Key (if applicable)
Note: Screen-shot images provided below is based on Windows Vista. You may see different screen on other operating systems but procedures are the same.
- Power on your computer and allow Windows 2000/ME/XP/Vista/Win7/win8/win10/win11 to load fully.
- Insert the product on your PC, and put CD driver in the CD Rom of PC , you will see the CD driver installation disk appearance on the bottom right corner of PC
- Click ’’My computer’’—Find the G disk and double-click for driver installation Automatic
- Driver Installation Automatic
- , You Can Connect The Wireless Router For Internet When Finish The Installation ,
FCC
Warning:
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>