evolur C147zwOJZIL Cruise Rider Stroller Owner’s Manual

evolur C147zwOJZIL Cruise Rider Stroller

Product Information

• Product Name: Cruise Rider
• Product Model: 0922R2-365EV
• Manufacturer: Evolur
• Product Registration: Scan the QR code or visit https://www.evolurbaby.com/customer-care/product-registration/
• Manufacturer’s Website: https://www.evolurbaby.com

Product Usage Instructions

Warnings

IMPORTANT! Failure to follow these warnings and the assembly instructions could result in improper usage and potential hazards. Please read all instructions carefully.

WARNINGS

IMPORTANT! FAILURE TO FOLLOW THESE WARNINGS AND THE ASSEMBLY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

• ADULT ASSEMBLY REQUIRED.
• NEVER LEAVE CHILD UNATTENDED. ALWAYS KEEP CHILD IN VIEW WHILE IN STROLLER.
• AVOID SERIOUS INJURY FROM FALLING OR SLIDING OUT. ALWAYS USE SEAT BELT. AFTER
• FASTENING BUCKLES, ADJUST BELTS TO GET A SNUG T AROUND YOUR CHILD.
• AVOID FINGER ENTRAPMENT: USE CARE WHEN FOLDING AND UNFOLDING THE STROLLER.
• BE CERTAIN THE STROLLER IS FULLY ERECTED AND LATCHED BEFORE ALLOWING YOUR CHILD NEAR THE STROLLER.
• NEVER USE STROLLER ON STAIRS OR ESCALATORS. YOU MAY SUDDENLY LOSE CONTROL OF THE STROLLER OR YOUR CHILD MAY FALL OUT. ALSO, USE EXTRA CARE WHEN GOING UP OR DOWN A STEP OR CURB.
• AVOID STRANGULATION.
• DO NOT PLACE ITEMS WITH A STRING AROUND YOUR CHILD’S NECK, SUSPEND STRINGS
• FROM THIS PRODUCT, OR ATTACH STRINGS TO TOYS.
• USE OF THE STROLLER WITH A CHILD WEIGHING MORE THAN 45 LB (20.5 KG) OR TALLER
• THAN 37.8 IN (96CM) WILL CAUSE A HAZARDOUS UNSTABLE CONDITION TO EXIST. USE THE STROLLER WITH ONLY ONE CHILD AT A TIME.
• TO PREVENT A HAZARDOUS, UNSTABLE CONDITION, NEVER PLACE PURSES, SHOPPING BAGS, PARCELS OR ACCESSORY ITEMS ON THE HANDLE (OTHER THAN APPROVED STROLLER BAGS). NEVER PLACE ANYTHING ON THE CANOPY.
• TO PREVENT A HAZARDOUS, UNSTABLE CONDITION, DO NOT PLACE MORE THAN 10 LB (4.5 KG) TOTAL IN THE STORAGE BASKET INCLUDING THE 2 LB (1 KG) IN THE BASKET POCKET.(IF SUPPLIED)
• TO AVOID BURNS, NEVER PUT HOT LIQUIDS IN THE CUP HOLDERS.(IF SUPPLIED)
• TO PREVENT TIPPING, DO NOT PLACE MORE THAN 3 LB (1.36 KG) TOTAL IN THE CUPHOLDERS/SNACK TRAY.
• DO NOT USE STORAGE BASKET AS A CHILD CARRIER.
• DO NOT ALLOW YOUR CHILD TO STAND ON THE BASKET. IT MAY COLLAPSE AND CAUSE INJURY.
• NEVER PLACE CHILD IN THE STROLLER WITH HEAD TOWARD FOOTREST.
• NEVER ALLOW YOUR STROLLER TO BE USED AS A TOY.
• DISCONTINUE USING YOUR STROLLER SHOULD IT BECOME DAMAGED OR BROKEN.
• STROLLER TO BE USED ONLY AT WALKING SPEED PRODUCT NOT INTENDED FOR USE WHILE JOGGING, SKATING, ETC.
• CAREGIVER MUST ALWAYS HELP CHILD GET INTO AND OUT OF THE STROLLER.
• NEVER LEAVE YOUR CHILD UNATTENDED IN THE STROLLER/RIDER. FIVE POINT SAFETY HARNESS SHOULD BE KEPT ON AT ALL TIMES WHEN A BABY/CHILD IS IN THE STROLLER/RIDER. NEVER HANG A SHOPPING BAG, PURSE, DIAPER BAG OR ANY OTHER
• BAG TO THE HANDLE OF THE STROLLER/RIDER. ADDITIONAL WEIGHT ON THE HANDLE COULD TIP THE STROLLER OR A BABY/CHILD COULD GET ENTANGLED BY A STRAPCAUSING SUFFOCATION OR INJURY. PLEASE FOLLOW ALL SAFETY PROTOCOLS WHILE USING THIS PRODUCT.
• THE STROLLER IS DESIGNED FOR USE ON FLAT OR GENTLY SLOPING SURFACES, AND MAY BE UNSTABLE ON HIGHER SLOPING AND UNEVEN SURFACES AND USERS SHOULD BE AWARE OF THE POSSIBILITY OF THE STROLLER ROLLING AWAY OR TIPPING OVER.
• WITH YOUR HAND THROUGH THE WRIST TETHER STRAP LOOP, PUSH THE STROLLER HOLDING BOTH HANDLES.
• THE FRONT WHEELS MAY WOBBLE OR OSCILLATE WHEN WALKING FAST.
• THE STROLLER CAN BE TAKEN UP CURB BY EITHER PRESSING DOWN ON THE HANDLES
• AND RAISING THE FRONT WHEELS AND MOUNTING THE CURB OR TURNING THE STROLLER AROUND AND PULLING THE STROLLER UP THE CURB.
• CAUTION IS REQUIRED WHEN PUSHING THE STROLLER ACROSS STEEP SLOPES OR UNEVEN SURFACES THIS MAY CAUSE STROLLER TO BECOME UNSTABLE AND FALL OVER.
• ALWAYS HOLD THE HANDLES FIRMLY.
• DO NOT RUN WITH THE STROLLER.
• WHENEVER YOU STOP, ALWAYS APPLY THE BRAKES BEFORE YOU LEAVE THE STROLLER.
• DO NOT HANG BAGS OR GOODS FROM THE HANDLE AS THIS COULD CAUSE THE STROLLER
• TO TIP OVER. THE UPRIGHT POSITIONS ARE NOT SUITABLE FOR A CHILD UNDER 6 MONTHS OLD.

PARTS

If there are any missing parts, please contact Evolur before using the product .

RIDER ASSEMBLY

1. Open the storage latch (figure A) and lift up the handle of the rider until it stands erect, clicking into place (figure B). Next, pull up on the handle to extend it (figures C and D). Note: each time you open the rider, ensure that it is completely latched.
2. Front Wheels: Slide each Front Wheel  onto the mounting post at the front ofthe rider until they click into place (figure E). To remove the Front Wheel, push the release button as shown in (figure F).
3. Rear Wheels: Put the Brake Rail into the left Rear Wheel until it clicks into place (figure G). Next, slide the left Rear Wheel into the wheel mount until it  clicks into place (figure H). Next, mountthe right Rear Wheel and slide the Brake Rail into the right Rear Wheel at the same time (figure I).
   • Note: Tug on the front and rear wheels to ensure that they are secure. To remove the Rear Wheels, release the pin lock as shown in (figure J).
4. To open up the seat, release the rotary button and simultaneously adjust the button to pull up the seat back (Figure A).
5. Support into the top of the seat back until it clicks into place (Figure B). To remove the Head Support, press the release button and release it (Figure C).
6. Guard Rail:
   • Put the Guard Rail Housing into the Seat until it clicks into place ( Figure D). Attach the Guard Rail to the Seat Back (Figure E).
   • To detach the Guard Rail, push the release button under Guard Rail Housing and pull out Guard Rail from Seat (Figure G).
   • Pull the release buttons on the side of the Seat Back to remove the Guard Rail (Figure H).

FOLDING THE RIDER

1. Press the Handle Adjust Button and push the handle downward (figures A & B).
2. Press the rotary button and the adjust button behind the seat back and proceed to fold the Seat Back down (figure C & D).
3. Press and hold the Folding Lock and pull the 2nd Lock upward to fold the rider (figures E and F). Next, allow the rider to drop and fold automatically (figures G & H).

USING THE HARNESS

WARNING:
USE THE HARNESS AT ALL TIMES. When not in use, disconnect shoulder straps fromthe waist strap and buckle to prevent trangulation.A five point harness is provided to restrain your child. Buckletongues separate for added safety. To econnect buckletongues and to secure the child in the harness, please followthe steps below carefully.

1. Slide the shoulder strap tongue (1) into the top of the waist buckle tongue (2) on both sides.
2. Push both buckle tongues (1+2) into the buckle housing (3) until the buckle tongues click into place.
3. You can tighten or loosen the crotch straps by sliding the bar sliders. The waist strap and harness needs to fit firmly around the child.
4. To tighten or loosen the shoulder strap, hold and lift the slider and then pull the harness strap, to adjust to the desired fit. The waist strap and harness needs to fit firmly around child.
5. To release the buckle from the buckle housing, squeeze the button on the buckle housing (figure A and B).

SECURING YOUR CHILD TO HARNESS

1. To tighten or loosen the shoulder strap, hold and lift the slider and then pull the harness strap, to adjust to the desired fit. The waist strap and harness needs to fit firmly around child.
2. To release the buckle from the buckle housing, squeeze the button on the buckle housing (figure A and B).

USING THE BRAKES

1. Push the brake rail down to park the stroller. Lift the brakes rail up to release the brakes as shown in figure A.

WARNING:

• ALWAYS APPLY THE BRAKES WHEN THE TROLLER IS STATIONARY.

ADJUST THE BACKREST

1. Adjustment of the reclined/upright position: Press the adjust button and the rotary button to adjust the backrest in reclined or upright position (figure A).

WARNING:

• ALWAYS APPLY THE BRAKES WHEN THE TROLLER IS STATIONARY.

USING THE T-BAR

1. To use the T-bar, remove the Guard Rail from the Guard Rail Housing and install the T-bar in its place (figure A).
2. When folding the rider, press the spring button  on Tbar and pull it out from the seat (figure B).

LIFTING AND CARRYING THE RIDER

1. To lift or carry the Stroller, ensure that the storage latch is engaged. rider so the rider is balanced.
2. Using the Shoulder Strap: Press the spring hook to attach the shoulder strap onto the the D-Ring onto the rear oint on the rider. Apply for both ends of the strap.
   • ATTENTION : Shoulder strap is not a toy. do not give to children to play with. Do not leave children unattended near the shoulder strap. This may pose a strangulation hazard.

PARTS LIST

USING THE CANOPY (SOLD SEPARATELY) PARTS LIST

ASSEMBLY

1. Insert the support bar into the fabric cover.
2. Hold the support bar from the back of the connector (Fig 3), then put the end of the support bar into the connector with another hand (Fig 4 & 5).
3. For the other side, pull out the center of the support bar slightly and insert the support bar into the connector (Fig 6).
4. Adjust the support bar into place Fig. 7.
5. Attach the holder to the handle bar connector. The cylinder on the handle bar should be aligned with the hole in the bracket (Fig 8).
6. Firmly fasten the xing buckle to the left until completely ejected (Fig 9). Try to shake and do not fall o to indicate that it is in place.
7. When disassembling the canopy, press the button and lift the xing buckle toward the side to open (Fig 10).
8. Press the metal pin inward to adjust the height (Fig11 & 12).

USING THE STROLLER CONNECTOR (SOLD SEPARATELY)

The connector can be used for most compact baby strollers.

1. Press the quick release button on the connector to connect it to the rider as shown in figure A/B/C. To detach the connector, press the quick release button to remove it.
2. To attach the connector to rear leg of your baby stroller, use the strap located on the other end of the connector. Make sure that the strap is tight enough to velcro it as shown in figures D/E/F.

ATTENTION:

• When using the connector on the left rear leg of your baby stroller, connect it to the right front leg of your Coast Rider, and vice versa. Refer to Figures G/H.

CARE AND MAINTENANCE

ROOM CLIMATE CONTROL:

• TO PROLONG THE LIFE OF YOUR STROLLER KEEP IT CLEAN AND DO NOT LEAVE IT IN THE DIRECT SUNLIGHT OR IN THE CAR BOOT FOR EXTENDED PERIODS OF TIME.
• REMOVABLE FABRIC COVERS AND TRIMS MAY BE CLEANED USING WARM WATER WITH A HOUSEHOLD SOAP OR MILD DETERGENT. ALLOW IT TO DRY FULLY, PREFERABLY AWAY FROM THE DIRECT SUNLIGHT.
• NON REMOVABLE FABRIC COVERS AND TRIMS MAY BE SPOT CLEANED USING A DAMP SPONGE WITH SOAP OR A MILD DETERGENT. ALLOW IT TO DRY COMPLETELY BEFORE FOLDING OR STORING IT AWAY.
• IN SOME CLIMATES THE COVERS AND TRIMS MAY BE AFFECTED BY MOLD AND MILDEW. TO HELP PREVENT THIS OCCURRING, DO NOT FOLD OR STORE THE PRODUCT IF IT IS DAMP OR WET. ALWAYS STORE THE PRODUCT IN A WELL VENTILATED AREA.
• WHEN USING YOUR STROLLER AT THE BEACH – COMPLETELY CLEAN YOUR STROLLER AFTERWARDS TO REMOVE THE SAND AND SALT FROM THE MECHANISMS AND WHEEL ASSEMBLY. SAND AND SALT WILL CAUSE PREMATURE WEAR AND CORROSION.
• IF THERE ARE COMPRESSION MARKS ON THE WHEELS – USE A DOMESTIC HAIR DRYER TO GENTLY WARM (DO NOT OVERHEAT) THE WHEELS AND THE COMPRESSION MARKS SHOULD SLOWLY DISAPPEAR.
• ALWAYS CHECK PARTS REGULARLY FOR TIGHTNESS OF SCREWS, NUTS, AND OTHER FASTENERS. TIGHTEN IF REQUIRED. TO MAINTAIN THE SAFETY OF YOUR NURSERY PRODUCT, SEEK PROMPT REPAIRS FOR BENT, TORN, WORN OR BROKEN PARTS.

LIMITED WARRANTY

• Evolur warrants its product to be free from defects in material and workmanship and agrees to remedy any such defect.
• This warranty covers 1 year from the date of original purchase.
• This warranty is valid only upon presentation of proof of purchase.
• This is solely limited to the repair or replacement of defective furniture components and no assembly labor is included.
• This warranty does not apply to any product which has been improperly assembled, subjected to misuse or abuse or which has been altered or repaired in any way.
• This warranty gives you specific legal rights and you may also have other rights which vary from State to State.

CONTACT

• 1532 S. WASHINGTON AVE STE1
• PISCATAWAY, NJ 08854-9908
• www.evolurbaby.com.
• Follow Us On
• @Evolurbaby
• @evolurbaby
• to get your nursery featured on our social media.
• E-mail: info@evolurbaby.com.
• Enter our monthly giveaway! Scan the QR code to register.
• Chat with us! Scan the QR code to Live Chat.
• www.evolurbaby.com/help.

Read all instructions before assembling and using product.
IMPORTANT – Keep instructions for future use.
Scan the QR code to register your product
https://www.evolurbaby.com/customer-care/product-registration/.

THANK YOU
For choosing Evolur and congratulations on joining our family; a family that has been transforming lives for over 30+ years!  We appreciate your feedback and wish you the very best in the coming years with your new addition. If you have any questionsor concerns please don’t hesitate to reach out to us. One of our trusted Customer Care representatives will be happy to assist you. Thank you again for entrusting us to provide you with safe and affordable baby products and accessories.

References

• Evolur Baby Furniture - Convertible Crib, Double Dresser, High Chair, Bassinet, Stroller & More
• Customer Care | évolur contacts and help - Evolur
• Product Recall Registration | Evolur

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>