Mitakis FT-03B Hearing Aids for Seniors User Manual

Mitakis FT-03B Hearing Aids for Seniors

Product Information

Product Introduction
The Mitakis FT-03B hearing aid is an in-ear device designed for experience distribution and compensatory hearing for patients with air-induced hearing loss. It consists of a microphone, signal processor amplifier circuit, receiver, battery, housing, and embedded software (version V 1.0). The hearing aid has the following performance parameters:

Model| Output sound maximum (dB) pressure value| High frequency mean (dB)| Maximum noise gain at full range (dB)| Full range sound gain (average high frequency) (dB)| Frequency response range
---|---|---|---|---|---
FT-03B| 113| 106| 50| 43| F1: 300Hz, F2: 4500Hz

The hearing aid also supports Bluetooth connectivity with version 5.2 and various protocols such as A2DP, AVRCP, HFP, HSP, and SPP. It has a working time of 8 hours when used as a hearing aid, 7 hours in call mode, and 6 hours in music mode. The charging time is approximately 1.5 hours. The battery capacity is 60mAh for the earphone and 400mAh for the charging case. The working distance is 10 meters and the input voltage/current is 5V/1A.

Product List

• Earphone x 2
• Charging case x 1
• Ear cap x 3 (S, M, L)
• Type-C cable x 1

Product Usage Instructions

Turn On / Off
The earbuds turn on automatically when taken out of the charging case and turn off automatically when put into the charging case. To turn on manually, long press the touch button of the earbuds for 2 seconds. To turn off manually, long press the button for 5 seconds.

Wearing

1. Choose an ear cap with a suitable size to fit over the sound mouth.
2. Hold the earphone with your index finger and thumb and push the head side of the eardrum into the ear canal.
3. Gently pull the earlobe down and push the earphone to the best position with your index finger.

Charging

To charge the hearing aid:

1. If the hearing aid indicator is steady blue, it is currently charging.
2. The hearing amplifiers have been fully charged if the indicator turns green.
3. It takes about 1.5 hours to fully charge the hearing amplifier.

Charging the Charging Case

1. Insert one end of the small head of the data cable into the charging interface on the charging case and the other end into the adapter.
2. Connect the adapter to the power supply. The green indicator light will turn on during charging, and the white indicator light will turn on when fully charged.
3. The fully charged case can charge the earbuds 3 times.

Thank you very much for choosing our Mitakis FT-03B hearing aid. To have a great experience, please read this manual carefully before use. If you have any problem during wearing, please contact us @ [email protected], we will help you asap.

Product Introduction

Product parameters

• Product name: In-ear hearing aid

• Model: FT-03B

• Scope of application: Experience distribution, compensatory hearing for patients with air-induced hearing loss
  Product Structure: The product consists of microphone, signal processor amplifier circuit, receiver, battery, housing and embedded software (version V1.0)

• Product performance parameters:

Specif ci ation data are based on laboratory test result.

Product Diagram

Remove the insulation sticker before use.

Product Iist

The specif ci product accessories shall be subject to the actual situation

Operation Guide

Turn on/off
The earbuds turn on automatically when it is taken out of the charging case and turn off automatically when they are put into the charging case. Long press the touch button of the earbuds for 2 s to turn on manually, and long press the button for 5 s to turn off manually.

Wearing

1. Choose a ear cap with suitable size to fit over the sound mouth;
2. Hold the earphone with your indexfing er and thumb and push the head side of the eardrum into the ear canal;
3. Gently pull the earlobe down and push the earphone to the best position with your index finger.

Charging

Charge the hearing aid

1. If the hearing aid indicator is steady blue, the hearing aid is charging.
2. The hearing amplifiers have been full-charged if the indicator is green.
3. It takes about 1.5 hours to charge the hearing amplifier fully.

Regularly clean and wipe the charging contacts of headphones and charging case; When the headset is low power, you will hear the “low power” prompt tone automatically when wearing it. It can be used for at least half an hour. A fter charging for 15 minutes, it can be used for another 2 hours.

Charging The Charging Case

1. Insert one end of the small head of the data cable into the charging interface on the charging box and the other end into the adapter.
2. Connect the adapter to the power supply:
3. Charging: green indicator light on,
4. Full-charged: white indicator light on
5. The fully charged case can charge the earbuds 3 times.

The specific product accessories are subject to the actual situation. If you have any questions, please contact the customer service in time.

Operation Guide

1. Bluetooth pairing

   • Take the earbud out of the charging case and wear them
   • Turn on your phone’s Bluetooth search device
   • Select“ Muama-BT ”for pairing
     When the earbud is paired with the mobile phone for the if rs t time, there is a prompt tone of “pair”. Bluetooth will automatically connect the next time you pair near the device.

2. Hearing Aid M ode
   It will automatically enter the Hearing Aid mode(when Bluetooth is not connected), click the button 3 times to switch to the next Hearing Aid program, The program selection is shown in the following table:Program mode| Applicable scenario| Prompt
   ---|---|---
   Program 1| indoor| indoor
   Program 2| outdoor| outdoor
   Program 3| Strong noise reduction| The noise reduction

3. Telephone mode (Bluetooth is paired )

4. When a call comes in, tap the touch button twice to answer the call, press and hold for 2 seconds to reject the call.

5. During a call, tap the touch button twice to hang up the call.

6. Music mode
   When Bluetooth is paired, please adjust the music volume through the mobile phone music APP.

7. Bluetooth mode
   The hearing aid function and the Bluetooth function can be used at the same time, the two programs are automatically switched, and there is no need to turn off the Bluetooth when using the hearing aid function.

8. Restore factory Settings
   Turn off and then long press the power button for 12 S , when hear “du” twice, and both the blue and green indicator light f iash 5 times ,it indicates that the earbuds is restored to factory Settings successfully.

General Fauit Seif-Reference Table

When problems occur in the use of your equipment, please refer to the following table for simple treatment:

scream

| 1. Excessive earwax in the ear canal 2 . The position of ear caps is incorrect

3. High volume

| 1. Clean the ear canal 2p.utTiatkoenthaegaeinarbuds out and

3 . Turn down the volume

noise

| 1. Low battery power

2. The sound hole is blocked

3. The touch switch is faulty

4.  Battery Fault

| 1. Charge the device

2. Clean the sound holes

3. send to repair 4.send to repair

nosound| 1. Low battery power

2. Battery Fault

| 1. Charge the device

2. send to repair

The Name And Content Of The Hazardous Substance In The Product

• The “hazardous substances” shown in this table will not cause any harm to human body and the environment under the normal use of the product.
• The “hazardous substances” and the components present in the form provide information to consumers and recycling practitioners about the presence of the relevant substances and facilitate the proper disposal of products when they are discarded.
• ” Waste Electrical appliances and electronic Recycling and Treatment Regulations” suggestive description
• The company advocates environmental protection and low carbon consumption experience, Suggestions have of the company products user when no longer need this product recycling and disposal of waste electric and electronic products shall keep countries related laws and regulations and hand it over to the local manufacturers with recycling qualification approved by the state for recycling, reduce resource waste, protect the earth’s natural environment.

Environmental Conditions

1. Normal working conditions

   • The environment temperature: 10℃ – 40℃
   • A tmospheric pressure: 86Kpa – 106Kpa
   • Relative humidity: ≤80%
   • Power supply: 1.2V – 3.7V

2. Transportation and storage conditions

   • Transport
     The packaged hearing aid can be transported by general cargo transportation, but should be protected from exposure, rain, snow, direct contact or mechanical collision. Transportation environment conditions should be: temperature 0 – 3 8 ℃ , relative humidity not more than 80%.

   • Storage
     If the hearing aid needs to be stored for a long time, it should be stored in the warehouse which with the ambient temperature between 0- 38 ℃ , relative humidity is not more than 8 0 %, has ventilation conditions and no corrosive odors that can affect the performance of hearing aids.

Eiectrical Safety Instructions

1. Hearing aid class
   • Device class: Internal power supply
   • Type of the device: Type B
   • The device is not an AP or APG
   • Equipment operation mode: continuous operation
2. Hearing aid electromagnetic compatibility
   • High-power devices can have electromagnetic interference with hearing AIDS, such as pacemakers. When using similar equipment, please
   • Consult a doctor. The electromagnetic compatibility of hearing AIDS complies with GB/T25102.13-2010 Electroacoustic hearing AIDS No

   • Part 13: Electromagnetic Compatibility (EMC) and has passed the EMC test
     When the hearing aid complies with the hearing aid immunity specified in GB/T25102.13, the field strength of the RF test signal

      | Bystander compatibility
     When in the following field intensity, IRL < 55 dB field intensity is expressed as V/ m
     Frequency range| 0.0 8~ 0.8| 0 .8~ 0.9 6| 0 .96~ 1 .4| 1.4~ 2 .0| 2 .0~ 3.0
     Microphone mode| /| 3| /| 2| /
     Pick up coil mode| /| /| /| /| /
     Point to microphone mode| /               /| /               /| /|

3. This section describes key components
   The manufacturer undertakes to provide technical data, such as circuit diagram and component list, to the manufacturer if the relevant conditions are met.Testing technicians. Hearing aid key components include: microphone, receiver, movement.

Contraindications And Precautions

Theoretically, any person with hearing loss may become a hearing aid user. Currently, there is no comprehensive quantitative indicator to measure whether the hearing loss person needs a hearing aid. However, medical attention should be considered first in the following cases, and then the doctor or the fitter should decide whether the hearing aid can be matched according to the needs:

1. Congenital atresia of the external ear or deformity of the external auditory canal, a large number of foreign bodies in the external auditory canal.
2. Sudden deafness, especially within 3 months.
3. Rapid progressive hearing loss.
4. Hearing loss is accompanied by vertigo, headache or earache.
5. Conductive deafness of any cause (external ear, middle ear infiammation, discharge, cerumen or foreign body embolism, etc.) .
6. Patients with acute external otitis, tympanitis, chronic suppurative otitis media ( in the purulent infection stage), acute purulent otitis media should not wear this hearing aid

A small number of users wearing hearing A IDS for the first time may have ear blocked、their voice is too loud and other feelings, generally，this situation will be gradually adapted within three months.

Safety And Precautions

1. The hearing aid should be placed in the charging base when not in use to avoid being lost or damaged
2. Do not place the hearing aid in an environment with high temperature (such as heat source, exposed fire source) and high humidity. Otherwise, the device may fail, catch fire, or explode.
3. Do not immerse the hearing aid in any liquid, the hearing aid should be removed before swimming or washing hair, bath; A fter swimming or bathing , hearing A IDS should not be worn until the ear canal is dry.
4. The surface of the hearing aid should be kept clean, and earwax should be cleaned regularly from the sound mouth of the hearing aid. If there is redness or swelling in the area where the skin is in contact with the headset, stop using it immediately and consult a doctor.
5. Do not disassemble the hearing aid by yourself.
6. hearing aid is not resistant to seawater, acid and alkaline solvents, chemical reagents and other corrosive liquids.
7. The equipment and accessories may contain some small parts. Please keep the equipment and accessories out of reach of children.
8. If the product is not used for a long time, please turn it off after fully charging, and put it in a cool and dry place.
9. please charge the device with the attached charging cable, when charging the device with a power adapter, the adapter should meets the corresponding safety standard or certified by CCC
10. Please do not discard the discarded hearing aids at will. If you need to discard them, please dispose of them in accordance with the relevant national regulations.

Thank you very much for choosing our Mitakis FT-03B hearing aid. To have a great experience, please read this manual carefully before use. If you have any problem during wearing, please contact us @ [email protected], we will help you asap.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>