tp-link TL-SG105PP-M2 5-Port 2.5G Desktop Switch Installation Guide
- June 12, 2024
- tp-link
Table of Contents
Installation Guide
2.5G Multi-Gigabit Desktop PoE++ Switch
Panel Explanation
Power LED
On: Power on
Off: Power off
PoE Max LED
On: 116 W ≤ Total power supply < 123 W
Flashing: Total power supply ≥ 123 W
Off: Total power supply < 116 W
Recovery Switch
On: The switch will constantly detect the working status of a PoE powered
device (PD). When the switch finds that the PD works abnormally, the switch
will reboot it.
Off: The PoE Auto Recovery function is disabled.
Link/Act and PoE Status LEDs
Connection
Note:
- PoE ports can also connect to non-PoE devices, but only transmit data.
- TL-SG105PP-M2 can supply up to 60 W for each PoE port and 123 W for all PoE ports.
Specifications
General Specifications
Standard| IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3bz, IEEE802.3x,
IEEE802.1p, IEEE802.3af, IEEE802.3at, IEEE802.3bt
---|---
Network Media (Cable)| 100Base-TX: UTP category 5 cable or above (max. 100 m)
1000Base-T: UTP category 5e cable or above (max. 100 m)
2.5GBase-T: UTP category 5e cable or above (max. 100 m)
Interface| 5 100 Mbps/1 Gbps/2.5 Gbps Auto-Negotiation RJ45 Ports
PoE Ports: Port 1-Port 4
Total Power Supply: 123 W
Switching Capacity| 25 Gbps
Transfer Method| Store-and-Forward
MAC Address Learning| Automatically learning, automatically aging
Power Supply| External Power Adapter
Input: 100-240 VAC, 50/60 Hz
Output: 53.5 VDC /2.43 A
Wall mountable| Yes
Distance bewteen mounting holes| 150mm
Environmental and Physical Specifications
| Operating Temperature | 0˚C to 40˚C (32˚F to 104˚F) |
|---|---|
| Storage Temperature | -40˚C to 70˚C (-40˚F to 158˚F) |
| Operating Humidity | 10% to 90% RH non-condensing |
| Storage Humidity | 5% to 90% RH non-condensing |
Frequently Asked Questions (FAQ)
Why is the Power LED not lit?
The Power LED should be lit when the power system is working normally. If the Power LED is not lit, please try the following: A1: Make sure the AC power cord is connected to the switch with power source properly. A2: Make sure the voltage of the power supply meets the requirements of the input voltage of the switch. A3: Make sure the power source is on.
Why is the Link/Act LED not lit while a device is connected to the corresponding port?
It is recommended that you check the following items: A1: Make sure that the cable connectors are firmly plugged into the switch and the device. A2: Make sure the connected device is turned on and works normally. A3: The cable must be less than 100 meters long (328 feet).
Why are PoE ports not supplying power for PoE devices?
When the total power consumption of connected PoE devices exceeds the maximum, the PoE port with a smaller port number has higher priority. The system will cut off power to the ports with larger port numbers to ensure supplying to other ports. Take TL-SG105PP-M2 as an example. If port 1, 2 and 4 are consuming 35 W respectively, and an additional PoE device with 23 W is connected to port 3, the system will cut off the power of port 4 to compensate for the overload.
What should I notice before using the PoE Auto Recovery feature?
A1: Before upgrading a connected PoE powered device (PD), disable PoE Auto Recovery to avoid the PD’s damage. A2: When a PD does not send data packets to the switch for a long period in certain scenarios (e.g. an IPC in sleep mode), disable PoE Auto Recovery to avoid the PD repeatedly rebooting.
To ask questions, find answers, and communicate with TP-Link users or
engineers, please visit https://community.tp-link.com to join TP-Link
Community.
For technical support and other information, please visit https://www.tp-
link.com/support , or simply scan the QR code.
http://www.tp-
link.com/support
EU declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives (EU)2015/863,
2014/30/EU, 2014/35/EU, and 2011/65/EU.
The original EU declaration of conformity may be found at https://www.tp-
link.com/en/ce.
UK declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of the Electromagnetic
Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations
2016.
The original UK declaration of conformity may be found at https://www.tp-
link.com/support/ukca/
**Safety Information**
Keep the device away from water, fire, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need
service, please contact us.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Adapter shall be installed near the equipment and shall be easily accessible.
Please read and follow the above safety information when operating the device.
We cannot guarantee that no accidents or damage will occur due to improper use
of the device. Please use this product with care and operate at your own risk.
© 2023 TP-Link 7106510264 REV1.0.0
Documents / Resources
| tp-
link TL-SG105PP-M2 5-Port 2.5G Desktop
Switch
[pdf] Installation Guide
TL-SG105PP-M2, TL-SG105PP-M2 5-Port 2.5G Desktop Switch, 5-Port 2.5G Desktop
Switch, 2.5G Desktop Switch, Desktop Switch, Switch
---|---